Canon imageRUNNER ADVANCE C5255 Series Service Manual page 972

COPIER > OPTION > FNC-SW
CARD-RNG Card number setting (department number)
Lv.2 Details To set the number of cards (departments) that can be used with the
Card Reader.
Use case When setting the number of cards (departments)
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 1 to 1000
Default value 1000
COMP-PRT Img proc memory allocate at job conflict
Lv.2 Details When making 2 or more composition prints (page number, number
of copies, stamp, date, booklet, watermark), memory for image
processing is allotted preferentially to print jobs.
Meanwhile, memory for image processing of scan/send and PDL input
becomes insufficient depending on the options and document size,
and these jobs might be unprocessed until composition prints are
finished.
If these jobs are interfered each other, image processing can be put
forward little by little by allotting memory equally to each job.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Print priority, 1: Equal allocation
Default value 0
ARCDT-SW ON/OFF of ARCDAT control
Lv.1 Details To set ON/OFF of ARCDAT control.
When "1: OFF" is set, the result of ARCDAT control is not reflected to
LUT.
When the hue variation occurs in the case of failure value displayed in
COPIER> DISPLAY> HT-C, turn OFF the ARCDAT control once and
check the hue.
If hue variation is alleviated, analyze the cause of ARCDAT control
error (developer, Patch Sensor, etc.).
Use case When hue variation occurs
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Be sure to set "0: ON" again when ARCDAT control recovers.
Display/adj/set range 0 to 1
0: ON, 1: OFF
Default value 0
Related service mode COPIER> DISPLAY> HT-C
8
Service Mode > COPIER > OPTION > FNC-SW
8 Service Mode > COPIER > OPTION > FNC-SW
COPIER > OPTION > FNC-SW
SJOB-CL Set of scan job canceling by logout
Lv.1 Details To set whether to cancel the scan job in operation by logout of the
user.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution The job with scanning completed cannot be canceled.
Display/adj/set range 0 to1
0: Disabled, 1: Enabled
Default value 0
PT-W-SET [Not used]
DELV-FN2 ON/OFF of Delivery Fan
Lv.2 Details To set ON/OFF of the Delivery Fan 2 (FM9) at a 1-sided job.
Use case When the stackability at 1-sided setting is low
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution When ON is set, be sure to receive approval from the user in advance
by explaining the following.
- Fan noise occurs.
- Curl may get worse to a certain extent (especially with moist paper).
Display/adj/set range 0 to 2
0: OFF, 1: Half speed, 2: Full speed
Default value 0
USB-RCNT Auto connect set at USB device disconnct
Lv.2 Details To set to enable/disable automatic connection when the USB device is
disconnected.
With the setting to disable automatic connection, USB device cannot
be used if disconnecting and then connecting the USB device. To
enable connection again, the power needs to be turned OFF/ON.
With the setting to enable automatic connection, reconnection is made
after disconnecting, and then connecting the USB device.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution With the setting to enable automatic connection, disconnecting of 1
area makes automatic connection of all USB devices if there is USB
hub.
Display/adj/set range 0 to 1
0: No automatic connection, 1: Automatic connection
Default value 0
8-152
8-152