Sorter; Adjust - Canon imageRUNNER ADVANCE C5255 Series Service Manual

SORTER

ADJUST

SORTER > ADJUST
PNCH-HLE Adj of punch hole pstn from paper edge
Lv.1 Details To adjust the length from the paper edge to the punch hole.
As the value is incremented by 1, the punch hole moves by 1 mm.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -4 to 2
Unit mm
Default value 0
STP-F1 Adj A4 front stpl pstn (45 deg): Fin-C1
Lv.1 Details To adjust the one front staple position on the A4 size paper.
As the value is incremented by 1, the staple position moves to the
rear side by 0.49mm.
Use case When the A4 paper front staple position is displaced
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range -6 to 6
Unit mm
Default value 0
STP-F2 Adj LTR front stpl pstn (45 deg): Fin-C1
Lv.1 Details To adjust the one front staple position on the LTR size paper.
As the value is incremented by 1, the staple position moves to the
rear side by 0.49mm.
Use case When the LTR paper front staple position is displaced
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range -6 to 6
Unit mm
Default value 0
STP-R1 Adj A4 rear staple pstn (45 deg): Fin-C1
Lv.1 Details To adjust the one rear staple position on the A4 size paper.
As the value is incremented by 1, the staple position moves to the
rear side by 0.49mm.
Use case When the A4 paper rear staple position is displaced
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range -6 to 6
Unit mm
Default value 0
8
Service Mode > SORTER > ADJUST
8 Service Mode > SORTER > ADJUST
SORTER > ADJUST
STP-R2 Adj LTR rear stpl pstn (45 deg): Fin-C1
Lv.1 Details To adjust the one rear staple position on the LTR size paper.
As the value is incremented by 1, the staple position moves to the
rear side by 0.49mm.
Use case When the LTR paper rear staple position is displaced
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range -6 to 6
Unit mm
Default value 0
STP-2P Adj front/rear 2-staple position: Fin-A1
Lv.1 Details To adjust the front/rear 2-staple position on Finisher.
As the value is incremented by 1, the staple position moves by
0.1mm.
+: Toward front
-: Toward rear
Use case When the front/rear 2-staple position is displaced
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -25 to 25
Unit mm
SDL-STP Adj Saddle staple position: Fin-C1
Lv.1 Details To adjust the staple position at the time of saddle stitching.
As the value is incremented by 1, the staple position moves
downward by 0.5 mm.
Use case When the fold position and the staple position are misaligned at the
time of saddle stitching
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range -3 to 3
Unit mm
Default value 0
SDL-ALG Adj Saddle alignment position: Fin-C1
Lv.1 Details To adjust the shift position of the Alignment Plate at the time of
saddle stitching.
As the value is incremented by 1, the alignment position moves
toward the center of the paper by 0.1mm.
Use case When an alignment failure occurs at the time of saddle stitching
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
Unit mm
Default value 0
8-243
8-243