Canon imageRUNNER ADVANCE C5255 Series Service Manual page 1015

COPIER > OPTION > USER
PCL-COPY Set of PCL COPIES command control method
Lv.2 Details To set the binder control method of COPIES command with PCL.
Select whether to use the control method of Canon-made PCL or use
the same control method of non-Canon-made PCL.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 65535
0: Control method of Canon-made PCL (following the value of COPIES
command that is specified for each page to control on a page basis)
1: Control method of non-Canon-made PCL (handling the value of
COPIES command, which is specified for page 1 when collating, as bind
figure while the value of COPIES command for the next page or later is
invalid. Same control applies as Canon-made PCL when not collating)
2 to 65535: For future use
Default value 0
CNT-SW Set default dspl items on charge counter
Lv.1 Details To set default display items of the charge counter on the Counter Check
screen.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0:
Counter 1 - Total 1: 101
Counter 2 - Total (Black 1): 108
Counter 3 - Copy (Full Color + Single Color/1): 232
Counter 4 - Total A (Full Color + Single Color/1): 149
1:
Counter 1 - Total 2: 102
Counter 2 - Copy (Full Color + Single Color/2): 231
Counter 3 - Total A (Full Color + Single Color/2): 148
Counter 4 - Copy (Black 2): 222
Counter 5 - Total A (Black 2): 133
Default value 0
TAB-ACC ON/OFF of auto cst change for tab ppr
Lv.1 Details To set to enable/disable auto cassette change when tab paper runs out.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Be sure to instruct the user to thoroughly comply the following:
- Use tab paper with the same number of tabs.
- Set tab paper.
Be sure to comply the above; otherwise, proper print is not available and
it can cause soiling inside the machine because of toner.
Display/adj/set range 0 to 1
0: Auto cassette change disabled, 1: Auto cassette change enabled
Default value 0
8
Service Mode > COPIER > OPTION > USER
8 Service Mode > COPIER > OPTION > USER
COPIER > OPTION > USER
BCNT-AST Set of inbox print charge target job
Lv.1 Details To set the job type that advances the count in inbox print with NE
Controller (ASSIST).
Use case When switching the job type that is subject to counting of the inbox print
with NE Controller
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: PDL job, 1: Copy job
Default value 0
PRJOB-CP Set count TX at RX/report print
Lv.2 Details To set to enable/disable a page-basis count pulse transmission to the
charge management device at the time of reception print or report print.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: No transmission, 1: Transmission
Default value 0
DFLT-CPY Setting of color mode for copy
Lv.1 Details To set the default color mode for copy operation.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 2
0: Based on Auto/ACS/Printer Driver settings, 1: Color mode, 2: Black
mode
Default value EUR: 2, Other: 0
DFLT-BOX Set of color mode for inbox print
Lv.1 Details To set the default color mode for inbox print operation.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 2
0: Based on Auto/ACS/Printer Driver settings, 1: Color mode, 2: Black
mode
Default value EUR: 2, Other: 0
DOC-REM Display/hide of original removal message
Lv.1 Details To set whether to display or hide the message to remove original when
scanning with DADF without opening/closing DADF after scanning with
the Copyboard.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Hide, 1: Display
Default value 0
8-195
8-195