Lighting System - Isuzu 1999 RODEO Workshop Manual

RODEO
BODY AND ACCESSORIES
Service Precaution . . . . . . . . . . . . . . . . . . . . . .
Headlight Bulb . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlight Assembly . . . . . . . . . . . . . . . . . . . . .
Headlight Adjustment . . . . . . . . . . . . . . . . . .
Fog Light Bulb . . . . . . . . . . . . . . . . . . . . . . . . . .
Fog Light Assembly . . . . . . . . . . . . . . . . . . . . .
Fog Light Adjustment . . . . . . . . . . . . . . . . . .
Side Marker Light Bulb . . . . . . . . . . . . . . . . . . .
Front Combination Light Assembly
Taillight Bulb . . . . . . . . . . . . . . . . . . . . . . . . . . . .
License Plate Light Bulb (Bumper Type)
License Plate Light Bulb (Tailgate Type)
Stoplight Bulb . . . . . . . . . . . . . . . . . . . . . . . . . . .
High Mounted Stoplight Assembly
High Mounted Stoplight Bulb
Backup Light Bulb . . . . . . . . . . . . . . . . . . . . . . .
Front Turn Signal Light Bulb
Rear Turn Signal Light Bulb
Dome Light Bulb . . . . . . . . . . . . . . . . . . . . . . . .
Courtesy Light Bulb . . . . . . . . . . . . . . . . . . . . . .
Service Precaution
WARNING: THIS VEHICLE HAS A SUPPLEMENTAL
RESTRAINT SYSTEM (SRS). REFER TO THE SRS
COMPONENT AND WIRING LOCATION VIEW IN
ORDER TO DETERMINE WHETHER YOU ARE
PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING. WHEN YOU
ARE PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING, REFER TO
THE SRS SERVICE INFORMATION. FAILURE TO
FOLLOW WARNINGS COULD RESULT IN POSSIBLE
AIR BAG DEPLOYMENT, PERSONAL INJURY, OR
OTHERWISE UNNEEDED SRS SYSTEM REPAIRS.

LIGHTING SYSTEM

CONTENTS
8A–1
8A–2
8A–2
8A–3
8A–3
8A–4
8A–4
8A–4
. . . . . . . . 8A–5
8A–5
. . . . 8A–6
. . . . 8A–6
8A–7
. . . . . . . . . 8A–7
. . . . . . . . . . . . . . 8A–8
8A–8
. . . . . . . . . . . . . . 8A–9
. . . . . . . . . . . . . . 8A–9
8A–10
8A–10
LIGHTING SYSTEM
Spotlight Bulb . . . . . . . . . . . . . . . . . . . . . . . . . . .
Luggage Room Light Bulb
HVAC Bezel Illumination Light Bulb
Shift Lever Illumination Light Bulb (A/T)
Vanity Mirror Illumination Light Bulb
Starter Switch . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lighting Switch (Combination Switch)
Dimmer·Passing Switch
(Combination Switch) . . . . . . . . . . . . . . . . . . .
Door Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Defogger Switch . . . . . . . . . . . . . . . . . . .
Key Remind Switch (Starter Switch)
Hazard Warning Light Switch
Stoplight Switch . . . . . . . . . . . . . . . . . . . . . . . . .
Backup Light Switch (M/T)
Turn Signal Light Switch
(Combination Switch) . . . . . . . . . . . . . . . . . . .
Illumination Controller . . . . . . . . . . . . . . . . . . . .
Light and Bulb Specifications
CAUTION: Always use the correct fastener in the
proper location. When you replace a fastener, use
ONLY the exact part number for that application.
ISUZU will call out those fasteners that require a
replacement after removal. ISUZU will also call out
the fasteners that require thread lockers or thread
sealant. UNLESS OTHERWISE SPECIFIED, do not
use supplemental coatings (Paints, greases, or other
corrosion inhibitors) on threaded fasteners or
fasteners joint interfaces. Generally, such coatings
adversely affect the fastener torque and the joint
clamping force, and may damage the fasteners.
When you install fasteners, use the correct
tightening sequence and specifications. Following
these instructions can help you avoid damage to
parts and systems.
SECTION
8A–1
8A–11
. . . . . . . . . . . . . . . . 8A–11
. . . . . . . . 8A–12
. . . . 8A–12
. . . . . . . . 8A–13
8A–13
. . . . . . 8A–14
8A–14
8A–15
8A–15
. . . . . . . 8A–16
. . . . . . . . . . . . . 8A–16
8A–16
. . . . . . . . . . . . . . . . 8A–17
8A–17
8A–17
. . . . . . . . . . . . . 8A–18