Table of Contents
Advertisement
2. Product Overview
2. Product Overview
2.4. Electrical Connections
The following sections describe all possible electrical connections of
the UBEX endpoint and MMU devices.
2.4.1. SFP / SFP+ Slots
DEFINITION:
The
small
form-factor
compact, hot-pluggable optical module transceiver used for both
telecommunication and data communication applications. It is a
popular industry format jointly developed and supported by many
network component vendors. The SFP interface supports data
rates up to 1 Gbit/s. *
DEFINITION:
The enhanced small form-factor pluggable (SFP+)
is an enhanced version of the SFP that supports data rates up to
10 Gbit/s. *
UBEX F-series endpoint devices and the Matrix
Management Unit contain standard 1x SFP
(in the case of the MMU) and 2x SFP+ (in the case of the endpoint
devices) slots for the fiber optical connections via SFP / SFP+ modules
or DAC cables. The installed SFP / SFP+ modules can be singlemode
or multimode as well.
Endpoint devices
Number of slots
2
Type of the slot
SFP+
Maximum bandwidth
10 Gbps
per slot
Audio, video,
Transmitted signal
Ethernet, RS-232
For the details about the DAC cable / SFP+ module installation see the
SFP / SFP+ Slot Connection
section.
Maximum Allowed Optical Cable Length
The maximum allowed optical cable
length depends of the installed SFP / SFP+
modules. Always check the specification
of the optical modules before the fiber
optical cabling.
* Source:
https://en.wikipedia.org/wiki/Small_form-factor_pluggable_
transceiver
Applied F-series endpoint firmware package: v1.4.1 | Applied R-series endpoint firmware package: v1.4.1 | Applied MMU firmware package: v1.2.1 | LDC software: v1.34.0b2
2.4.2. AC Power Connection
Standard IEC Connector
UBEX F-series endpoint devices and the Matrix
Management Unit contain standard IEC power connector
and works with 100 to 240 Volts AC, 50 Hz or 60 Hz
pluggable
(SFP)
is
a
power sources.
Connect the power cord to the AC input connector; the
extender is immediately powered on.
Neutrik powerCON TRUE1 Connector
UBEX R-series endpoint devices contains Neutrik
powerCON TRUE1 NAC3MPX-WOT power connector
and works with 100 to 240 Volts AC, 50 Hz or 60 Hz
power sources.
Connect the Neutrik powerCON to the AC input
connector; the extender is immediately powered on.
See the details about the assembly instructions for the Neutrik
powerCON TRUE1 cables on the website of the vendor:
https://www.neutrik.com/en/product/nac3mx-w-top
MMU
2.4.3. Symmetrical Analog Stereo Audio Connector
1
5-pole Phoenix connector is used for balanced analog audio (line
SFP
in/out). Unbalanced audio signals can be connected as well. For
asymmetrical output, connect only + and ground. For asymmetrical
1 Gbps
input connect + and ground to the source and connect – to the ground.
Compatible Plug Type
Ethernet only
Phoenix
®
See more information about the most common audio cable wiring
modes in
You can find more information about audio embedding and de-
embedding functions in the
UBEX series – Matrix Application Mode – User's Manual
UBEX series – Matrix Application Mode – User's Manual
Combicon series (3.5mm pitch), type: MC 1.5/5-ST-3.5.
Pin nr.
Signal
1
Left +
2
Left -
3
Ground
4
Right -
5
Right +
5-pole Phoenix connector pin assignments
Audio Cable Wiring Guide
section.
Audio Interface
section.
2.4.4. RS-232 Connector
UBEX-PRO20-HDMI-F110 model and the Matrix Management Unit
contains a 3-pole Phoenix connector which is used for RS-232 serial
connection.
Pin nr.
Signal
1
Ground
2
TX data
3
RX data
RS-232 connector pin assignments
Compatible Plug Type
Phoenix
Combicon series (3.5mm pitch, 3-pole), type: MC 1.5/3-ST-3.5.
®
You can find help for the correct wiring in the
Serial Data Transmission
section.
You can find more information about serial interface in the
Interface
section.
2.4.5. USB Mini-B Connector
UBEX series devices provide standard USB 2.0 mini B-type
connector for software control and firmware upgrade purpose.
INFO:
The USB control function of the MMU will be added by future
firmware update.
2.4.6. IR Connector
IR detector and IR emitter can be connected to the enpoint device with
TRS (Tip, Ring, and Sleeve) connectors. They are also known
as (3,5 mm or approx. 1/8") audio jack, phone jack, phone plug,
and mini-jack plug. The pin assignments are the following for
the detector and the emitter:
Detector – 3-pole TRS
1 Tip
Signal (active low)
1 Tip
2 Ring
GND
2 Ring
3 Sleeve
+5V
3 Sleeve
INFO:
Ring pole of the emitter is optional. If your IR emitter has
three-pole TRS plug, then the Ring and the Sleeve are the same
signal (Output - ).
22
22
Cable Wiring Guide for
Serial
Emitter – 2-pole TS
+5V
Signal (active low)
Advertisement
Table of Contents
Troubleshooting
