Electrical Connections; Sfp / Sfp+ Slots; Ac Power Connection; Hdmi Connector - Lightware UBEX-PRO20-HDMI-F100 User Manual

 
     
4. Installation 4. Installation
4.3. Electrical Connections
The following sections describe all possible electrical connections of the UBEX endpoint devices.
4.3.1. SFP / SFP+ Slots
DEFINITION:
The small form-factor pluggable (SFP) is a compact, hot-pluggable optical module transceiver
used for both telecommunication and data communication applications. It is a popular industry format
jointly developed and supported by many network component vendors. *

DEFINITION: The enhanced small form-factor pluggable (SFP+) is an enhanced version of the SFP that
supports data rates up to 10 Gbit/s. *
* Source: https://en.wikipedia.org/wiki/Small_form-factor_pluggable_transceiver
UBEX F-series endpoint devices contain 2 pieces standard SFP+ slots for the fiber
optical connections via SFP+ modules or DAC cables. The installedSFP+ modules can
be singlemode or multimode as well.
Number of slots
Type of the slot
Maximum bandwidth per slot
Transmitted signal
For the details about the DAC cable / SFP+ module installation see the
Maximum Allowed Optical Cable Length
The maximum allowed optical cable length depends of the installed SFP+
modules. Always check the specification of the optical modules before the fiber
optical cabling.
4.3.2. AC Power Connection
Standard IEC Connector
UBEX F-series endpoint devices contain standard IEC power connector and works with 100 to
240 Volts AC, 50 Hz or 60 Hz power sources.
Connect the power cord to the AC input connector; the extender is immediately powered on.
Neutrik powerCON TRUE1 Connector
UBEX R-series endpoint devices contains Neutrik powerCON TRUE1 NAC3MPX-WOT power
connector and works with 100 to 240 Volts AC, 50 Hz or 60 Hz power sources.
Connect the Neutrik powerCON to the AC input connector; the extender is immediately
powered on.
See the details about the assembly instructions for the Neutrik powerCON TRUE1 cables on
the website of the vendor: https://www.neutrik.com/en/product/nac3mx-w-top
series – Extender Application Mode – User's Manual series – Extender Application Mode – User's Manual
Endpoint devices
2
SFP+
10 Gbps
Audio, video, Ethernet, RS-232
SFP+ Slot Connection section.
Applied F-series endpoint firmware package: v2.0.0 | Applied R-series endpoint firmware package: v2.0.0 | LDC software: v2.5.9b3
4.3.3. HDMI Connector
The endpoint device provides standard 19-pole HDMI connector for inputs and outputs with
HDMI 2.0 support. Always use high quality HDMI cable for connecting sources and displays.
See more details about the AV interfaces in the
4.3.4. Symmetrical Analog Stereo Audio Connector
5-pole Phoenix connector is used for balanced analog audio (line in/out). Unbalanced audio signals can be
connected as well. For asymmetrical output, connect only + and ground. For asymmetrical input connect +
and ground to the source and connect – to the ground.
Compatible Plug Type
Phoenix Combicon series (3.5mm pitch), type: MC 1.5/5-ST-3.5.
®
5-pole Phoenix connector pin assignments
See more information about the most common audio cable wiring modes in
You can find more information about audio embedding and de-embedding functions in the
section.
4.3.5. RS-232 Connector
UBEX-PRO20-HDMI-F110 model contains a 3-pole Phoenix connector which is used for RS-232 serial
connection.
RS-232 connector pin assignments
Compatible Plug Type
Phoenix Combicon series (3.5mm pitch, 3-pole), type: MC 1.5/3-ST-3.5.
®
You can find help for the correct wiring in the
You can find more information about serial interface in the
Video Interface and the Audio Interface sections.
Pin nr. Signal
1 Left +
2 Left -
3 Ground
4 Right -
5 Right +
Audio Ports section.
Pin nr. Signal
1 Ground
2 TX data
3 RX data
Serial Ports section.
Serial Interface section.
34 34
Audio Interface