Control Data Corporation CYBER 170 Series Operator's Manual page 308

Warning message 3-9
Cluster address 7-5
CMAP switch setting 2-3
CMRDECK
Flaw entries 6-7
Modification 2-24
Selection 2-10,11,19
CM RINST 2-24
Coldstart
Controlware 2-1,2,3
Deadstart panel settings 2-3,4,5,6
Definition C-l
Disk controller 2-2
From card reader 2-2,4
From disk unit 2-2,3
From tape unit 2-1,2
Procedures 2-1
Tape Controller 2-2
Commands, DIS 5-8,9,10,11
Commands, DSD
BATCmO Equipment 3-17
Channel control 3-27
Dayfile 3-
i;
4-2
Entryof 1-2,3
Job processing control 3-2
Memoryentry 3-26
Peripheral equipment control 3-9
Restricted entry of 3-24,25,26
Subsystem control 3-18
System control 3-21
Transaction subsystem 3-28
COMMENT command 3-8
Common Testing and Initialization (CTI)
CTI displays 2-13
Definition C-l
Loading CTI 2-6
Procedure 2-1
Communications area display 4-30,31
Communications supervisor 7-1
Configuration of system 1-1
Configuration, mass storage display 4-13
Configura tion, PP H-l
Configure removable devices 3-13
Console
Keyboar.d illustration 1-2
Keyboard locking 3-24
Keyboard unlocking 3-24
Messages B-1
Operations (DIS) 5-7
Operations (DSD) 3-1
Screen control D-I0
CONTINUE command 3-17
Control
Channel 3-27
Job processing 3-2
Keys (console) 1-3,4; 5-7
Peripheral equipment 3-9
Subsystem 3-18
System 3-21
Control point
Assigning equipment to 3-9
Assigning programs/utilities 3-24
Assignment for subsystems 2-27; 3-18
Automatic assignment 2-27
Clear pause bit 3-9
Dropping 3-8,21,26
File name table 5-1
Idling 3-23
Setting sense switches 3-9,18,19,20,21
Status (J) display 4-24,26
Control statement display 5-2
Control statement entry command 5-1,9
Control word 4-35
• Index-2
Controller reservations 8-4
Controlware 2-1,2,3; C-l
CP command '3-2
CPU
INPUT MODE 5-9
Job switch interval 3-7
Priority 3-3,4
Program exit mode 5-9
Recall period 3-7
Status 2-17
Time slice 3-4
Tuming off or on 2-17
CR (carriage return) key, use of 1-4; 2-13; 5-7,8
CR command 3-2
Create multispindle device (pack) 3-13,16
CS 7-1; C-l
CTI
Displays 2-13
Loading 2-6
Procedure 2-1
CYBERLOG displays 2-28
D display (DIS) 5-1
D display (DSD) 4-8,9
Data storage display (DIS) 5-1,4
DATE command 3-25
Date entry 2-26
DAYFILE command 3-2
Dayfile commands 3-1; 4-2
Dayfile, comments entered 3-8
Dayfile (A) displays 4-2; 5-1,2
Dayfile messages 4-2,3
DCH command 3-28
DCN command 3-28
DCP command 5-9
DDP 'I-I; 4-13
DDS 2-1,8
Deactivate channel 3-28
Deadstart
Alterna te 2-20
Automatic 2-13
CMRDECK
Modification 2-24
Selection 2-10,11
Coldstart '2-1
CTI
Loading 2-6
Options 2-13
Procedure 2-1
Definition C-l
DDS
Display 2-15
Loading 2-8
Equipment 2-3,4
Error processing 2-36
Express deadstart dump (EDD) 2-21
File 2-1,6
Hardware reconfiguration (*H*) display 2-16
Mass storage 2-1,7
Initial options (* A *) display 2-7,13
Initialization 2-26
IPRDECK modification 2-26
Keyboard entries 2-13
For H display 2-17,18
For P display 2-19
Level 2-11,34,35
Maintenance 2-13
Memory Check 2-14
Offline maintenance (*M*) display 2-13
Operator intervention (*0*) display 2-15
Panel parameters (*p*) display 2-18
60435600 L