External Delivery Sensor; Before Removing The External Delivery Sensor; Removing The External Delivery Sensor; Internal Delivery Sensor - Canon imageRUNNER 5065 series Service Manual

9.5.14 External Delivery Sensor

9.5.14.1 Before Removing the External Delivery Sensor

iR5065 / iR 5055 / iR5075 / / /
1) Detach the duplexing
12)Reference[Removing the Duplexing Feed Front Cover]
2) Slide out the fixing/feeding unit. (page 9-18)Reference[Removing the
Fixing/Feeding unit]
3) Remove the external delivery roller. (page 9-24)Reference[Removing
the External Delivery Roller]

9.5.14.2 Removing the External Delivery Sensor

iR5065 / iR 5055 / iR5075 / / /
1) Slide out the sensor support plate.
- 2 screws [1]
2) Remove the external delivery jam sensor [2] from the sensor support plate.
- 1 connector [1]
[1]

9.5.15 Internal Delivery Sensor

9.5.15.1 Before Removing the Internal Delivery Sensor

iR5065 / iR 5055 / iR5075 / / /
1) Detach the duplexing
12)Reference[Removing the Duplexing Feed Front Cover]
2) Slide out the fixing/feeding unit. (page 9-18)Reference[Removing the
Fixing/Feeding unit]
3) Detach the fixing front cover. (page 10-14)Reference[Removing the
Fixing Front Cover]
4) Detach the fixing/feeding
13)Reference[Removing the Fixing/Feeding Unit Front Cover]
5) Detach the fixing/feeding unit middle cover. (page
13)Reference[Removing the Fixing/Feeding Unit Middle Cover]
[2] [1]
F-9-107
feed front cover. (page
[1]
[2]
F-9-108
[2]
F-9-109
feed front cover. (page
unit front cover.
(page
6) Detach the fixing upper cover. (page 10-13)Reference[Removing the
Fixing Upper Cover]
7) Remove the fixing drive assembly. (page 10-20)Reference[Removing
the Fixing Drive Assembly]
8) Remove the fixing upper unit. (page 9-19)Reference[Removing the
Fixing Upper Unit]
9) Remove the
38)Reference[Removing the Lower Separation Claw (Unit)]
10) Remove the internal delivery roller. (page 9-25)Reference[Removing
the Internal Delivery Roller]

9.5.15.2 Removing the Internal Delivery Sensor

iR5065 / iR 5055 / iR5075 / / /
1) Remove the protrusion [2] to slide out the sensor support plate [3].
- 1 screw [1]
0015-7196
10-
0015-5066
2) Remove the internal delivery sensor [2] from the sensor support plate.
- 1 connector [1]
[1]

9.5.16 Fixing Inlet Sensor

9.5.16.1 Before Removing the Fixing Inlet Sensor

iR5065 / iR 5055 / iR5075 / / /
1) Detach the
12)Reference[Removing the Duplexing Feed Front Cover]
2) Slide out the fixing/feeding unit. (page 9-18)Reference[Removing the
Fixing/Feeding unit]

9.5.16.2 Removing the Fixing Inlet Sensor

iR5065 / iR 5055 / iR5075 / / /
1) Check the positions (front, rear) of the fixing inlet guide base (the relative
positions between the marking line of the fixing inlet guide base and the
indexes of the height adjusting support plate). Then remove the 2 screws
[3] and the 1 connector [4] and remove the fixing inlet guide base [5].
0015-7198
10-
10-
10-
lower separation claw unit.
[1] [3] [2]
F-9-110
[2]
F-9-111
duplexing feed front cover.
Chapter 9
(page 9-
0015-5067
0015-8346
(page 10-
0015-5068
9-33