Error Codes - Canon imageRUNNER 5065 series Service Manual

Chapter 16
Cause
There is a shortage of TCP/IP resources. Try again later.
While continuous transmission is under way or has ended in FTP or
Windows (SMB), a shortage of TCP/IP resources has occurred, not
permitting reference.
Set the IP address.
The IP address of the machine has yet to be set.
The server does not respond. Check the settings.
The settings of the selected server are not correct, or the server has not been
turned on. Or, there may be a shortage of resources.
NetWare is in use. Try again later.
NetWare is printing using PSeve or NDSPServer, not permitting browsing. Wait until NetWare finishes printing; then, try again.
The layer in question at the target is too deep to browse.
The number of characters is in excess of the number allowed.
There is no response.
The server is not ready for file transmission.
The network is cut for file transmission. (An attempt to connect to the target
of transmission may have failed, or there is an open circuit in the middle.)
The tree name is not specified for NetWare transmission.
An error has occurred for TCP/IP in the course of e-mail or i-fax
transmission.
Check TCP/IP.
The machine's TCP/IP is not in operation.
The selected server cannot be found. Check the settings.
The IP address in question cannot be identified.
If the login information for the LDAP server is set to 'use (security
authentication)', the host name in question cannot be identified.
The selected server cannot be connected. Check the settings.
An attempt to connect to the IP address/port in question fails.
Check the user name, password, or the settings.
If the login information of the LDAP server is set to 'use' or 'use (security
authentication)', the user name or the password is wrong.
If the login information of the LDAP server is set to 'use (security
authentication)', the domain name is wrong.
A timeout condition has occurred, and a search cannot be completed. Check the settings.
The search cannot be completed within the specified period of time.
An upper limit for search results has been exceeded. If the desired address is not indicated in the results, change the search conditions.
The number of matches has exceeded the number of results brought up in
response to the search.
The search conditions include a character that cannot be used for the selected server.
The symbol \ is used in the search condition.
The combination of characters used in the search condition fails to make up
a correct search condition.
There must be as many "s as there are "s
The symbol * is not included within parentheses.
If LDAP of the server and the character code is version 2 (JIS), there is a
character that is not part of the ASCII code (0x20-0x7E).
The version setting of the server is wrong, and the search cannot be initiated. Check the settings.
In user mode, the LDAP server settings (server LDAP version and character
code) is set for version 3; however, the LDAP server is operating for version
2.

16.3.2 Error Codes

iR5065 / iR 5055 / iR5075 / / /
Cause
# 001
There is a paper or original jam.
# 003
A communication lasting longer than a specific period of time (64 min) will
cause an error state.
# 005
The target does not respond within 35 sec.
The target is a non-G3 model.
# 009
16-12
T-16-6
Remedy
Wait a while; then, try again.
In user mode, set the IP address; thereafter, turn off and then on the machine.
Wait a while; then, try again. If browsing is still not permitted, select a different server.
The layer in question cannot be specified. Specify a different address.
Check the target.
Check the network.
Type in the tree name.
Check the condition of the network cable and the connector.
In user mode, check the TCP/IP settings (IP address, DHCP, RARP, BOOTP).
1. In user mode, check the DNS settings.
2. On the DNS side, check the DNS data settings.
In user mode, check the TCP/IP settings (DNS settings).
1. In user mode, check the TCP/IP settings (gateway address of the IP address settings).
2. In user mode, check the LDAP server settings.
3. Check to see that the LDAP server is operating normally.
4. If the login information of the LDAP server is set to 'use (security authentication)',
check to see if the UDP packet is blocked by a filter.
In user mode, check the LDAP server settings (user name, password).
In user mode, check the LDAP server settings (domain name).
In user mode, increase the length of time before a timeout condition occurs (part of
LDAP server settings).
1. Narrow down the search conditions, and try again.
2. Try increasing the upper limit.
Remove the symbol \ from the search condition, and try once again.
Check to be sure that the combination of characters is in keeping with the rule; then, try
once again.
Remove any character that cannot be used; then, try once gain.
In user mode, set the LDAP server settings so that the LDAP server version and the
character code are both version 2.
T-16-7
Remedy
Remove the jammed paper or original.
1. Decrease the resolution for transmission.
2. In the case of reception, ask the source to decrease the resolution or divide the
original.
Check to be sure that the target is ready to communicate; then, try once again.
Check the target.
0015-5630