Canon imageRUNNER 5065 series Service Manual page 530

Chapter 17
Sub-item Description
DHOF-TM Use it to set the timing at which the drum heater goes off in sleep mode (with reference to clock time).
setting: 0 to 24 (default: 01; in hr)
DHOF-IVL Use it to set the timing at which the drum heater goes off in sleep mode (with reference to time after a shift to sleep mode).
setting: 0, 15 to 1440 (default: 0; in min)
CBLTINVL Use it to change the number of times the fixing web solenoid goes on.
Make use of it when image faults occur as the result of soiling on the pressure roller.
Setting
0: normal (default)
1: twice normal
CCD-LUT Usage setting for the CCD gain correction data
Use this item to correct the image deterioration (difference in density at center seam of image) due to aging.
Set enabling/disabling data usage corrected with one of the followings: COPIER > FUNCTION > CCD > LUT-ADJ, or LUT-
ADJ2.
Setting value:
0: not use [default]
1: use (LUT-ADJ correction data) [not available with this machine]
2: use (LUT-ADJ2 correction data)
ABC-MODE Switching the background processing of document (switching digital ABC setting)
Setting value:
-1: not switch the background density (setting for photo document and document with complex modeling)
0: default
1 to 3: bigger the value is set, lighter the background density is.
SJOB-CL Set whether or not to permit cancellation of the scanning job when a user performs logout.
Cancel the operating scanning job when a user performs logout.
[Remarks]
- "Scanning job" means a job for which scanning operation is completed, and the operation cannot be canceled when the scanning
operation is being executed.
- Cancellation performed by this mode is saved in the log in the same manner as cancellation performed by a user.
Setting range:
0: Cancellation prohibited
1: Cancellation permitted
Factory setting value: 0
IFX-CHIG Set the number of characters to ignore the email message received by IFAX.
When the number of characters in the email message received by IFAX is less than the specified number of characters, the message
is ignored and is not printed or transferred.
When a number other than "0" is specified for the number of characters and the email message disappeared, and also when no TIFF
file exists, a blank page with header and footer is printed and transferred.
* A kanji character is recognized as a two-byte character. A control code such as CR is also included in the number of characters.
Setting range:
0 to 999 (Unit: number of characters)
0: Do not ignore the email message.
Factory setting value: 0
BOX-BKUP For restore control of the BOX backup function.
SCANTYPE Switch the type of reader.
This is a service mode used to change the default reader to the optional reader.
Use this mode to change the CIS reader to CCD reader.
Setting range:
0: default reader
1: Optional reader
Factory setting value: 0
GR-ADJ-L Specify the gain setting level for linearity of Red color on the backside.
Specify the gain setting level to adjust linearity of the image on the backside against the image on the front side.
RAG-CONT Set the level of fixing smear control mode.
0: No smear
1: Small level of smear
2: Middle level of smear
3: Large level of smear
OR-ADJ-L Specify the offset setting level for linearity of Red color on the backside.
Specify the offset setting level to adjust linearity of the image on the backside against the image on the front side.
Setting value: -5 to 5 (default: 0)
ABC-MD2 Adjust the level of base density correction level for reading the backside.
Setting value: -1 to 3 (default: 0)
MXSPDSEL To set the skew correction (the idle rotation setting) for different paper width mixed in the original tray.
When the skew movement found, perform the idle rotation (additional 2 rotations) in the DF path to increase the paper loop counts
of the registration roller; this will correct the skew movement.
Setting:
0: w/ idle rotation [default]
1: w/o idle rotation
PO-CNTMD Use it to select the number of times the potential control mechanism goes on.
0: once at power-on
1: once at power-on and, in addition, 10 and 60 min thereafter (simplified potential control mode)
2: once at power-on and, in addition, 10 and 60 min thereafter (normal potential control mode; default)
W-CLN-P Use it to set the interval at which the primary charging wire is automatically cleaned.
setting: every 100 to 2000 (sheets; default at 2000)
IDL-MODE Use it to select idle rotation mode for the developing assembly.
0: fix to low humidity mode (off)
1: environment control (default)
2: fix to normal temperature/humidity mode (idle rotation for 120 sec)
3: fix to high humidity mode (idle rotation for 300 sec)
4: power save mode
17-34
COPIER > OPTION > BODY
Level
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2