Canon imageRUNNER 5065 series Service Manual page 526

Chapter 17
Sub-item Description
LANG-ERR Clear the language-related error.
Use this mode to recover from an error when a language-related error occurs after the language setting is changed from the default.
(The setting is returned to the default value after recovery.)
DF-RCON Initialize the backup data of DF-RCON board (EEPROM)
Clear the EEPROM value used to maintain backup data installed in DF-RCON and initialize the data.
SND-STUP Use it to reset the transmission read settings.
The transmission read settings will be reset when the main power switch is turned off and then back on.
Procedure
1) Select the item, and press the OK key.
2) Turn off and then back on the main power.
CA-KEY Use it to reset the CA certificate and key.
The CA certificate and the key will be reset when the main power switch is turned off and then back on.
Procedure
1) Select the item, and press the OK key.
2) Turn off and then back on the main power.
KEY-CLR Clear the encryption key for the HDD encryption board.
Clear the key to replace the encryption key in the HDD encryption board (security kit).
Select KEY-CLR and press the OK key to clear the encryption key.
When turning off/on the main power after performing this operation, the encryption board installation process operates, and a new
encryption key is generated.
Note) When this operation is performed, all the data in HDD become unavailable. Therefore, when turning off/on the main power
after performing this operation, it is necessary to start from formatting of HDD.
<MISC-R>
Sub-item Description
SCANLAMP Use it to turn on the scanning lamp.
Procedure
1) Select the item.
2) Press the OK key so that the scanning lamp goes on and remains on for 3 sec.
<MISC-P>
Sub-item Description
P-PRINT Use it to print out service mode settings.
Procedure
1) Select the item.
2) Press the OK key to generate a printout.
USER-PRT Use it to print out user mode settings.
Procedure
1) Select the item.
2) Press the OK key to generate a printout.
PRE-EXP Checking the pre-exposure lamp (LED).
1) Select the item to highlight.
2) Press the OK key to execute various operations for several seconds. The operation will stop automatically. (full activation)
3) Press the OK key to generate a printout.
Reference
If the photosensitive drum suffers a fault as the result of lamp activation, rotate the drum.
D-PRINT Use it to print out service mode settings (DISPLAY).
The settings under DISPLAY will be printed (not including P-PRINT, LBL-PRINT, HIST-PRINT and ALARM).
Procedure
1) Select the item.
2) Press the OK key to generate a printout.
ENV-PRT Use it to print out a log of changes in the machine inside temperature/humidity and in fixing temperature.
The log will show changes in the machine inside temperature/humidity and in fixing temperature (center) collected from the
monitor outputs of the non-contact thermistor and the environment sensor.
1) Select the item.
2) Press the OK key to generate a printout.
KEY-HIST Use it to print out the history of control panel key inputs.
1) Select the item.
2) Press the OK key to generate a printout.
TRS-DATA Transition of memory reception data.
Transmit the memory reception data to the data BOX.
Operation Method:
1) Select the item.
2) Press [OK] so that the data is transmitted.
LBL-PRNT Print the service label.
Print the description on the service label.
Operation Method:
1) Set an A4/LTR in Cassette 1.
2) Select the item.
3) Press [OK] so that the label is printed.
It will take about 15 sec to start printing.
HIST-PRT Use it to print out the jam history and the error history.
Procedure
1) Select the item.
2) Press the OK key to generate a printout.
<SENS-ADJ>
17-30
COPIER > FUNCTION > CLEAR
T-17-46
COPIER > FUNCTION > MISC-R
T-17-47
COPIER > FUNCTION > MISC-P
Level
1
1
2
2
2
Level
1
Level
1
1
1
1
1
1
1
1
2