Table of Contents
Advertisement
Sub-item
Description
DHCP-12
Set whether or not to validate the DHCP-Option 12 request.
When the DHCP-12 switch is set to ON, an inquiry about a host name (Option 12) is made by using the DHCP-Option 55.
*DHCP (Dynamic Host Configuration Protocol)
Setting range:
0: OFF, 1: ON
Factory setting value: 1
DHCP-81
Set whether or not to validate the DHCP-Option 81 request.
When the DHCP-81 switch is set to ON and the dynamic DNS setting is set to ON in the user mode, dynamic change of an IP
address by DHCP Option 81 is validated.
Setting range:
0: OFF, 1: ON
Factory setting value: 1
USB-RCNT
Set whether or not to perform automatic connection when disconnecting the USB device. (USB RECONNECT)
Setting range:
0: Do not perform automatic connection.
1: Perform automatic connection.
Factory setting value: 0
UI-COPY
Make a setting to switch the display in the copy screen in the control panel.
This mode is available for a user who does not want to display a print job screen on the control panel.
Setting range:
0: Hide the copy screen.
1: Do not hide the copy screen.[default]
PP-LWRT
Not used
<USER>
Sub-item
Description
COPY-LIM
Use it to put an upper limit to the number of copies.
setting: 1 to 9999 (default: 9999)
SLEEP
Use it to enable/disable the sleep function.
setting
0: off
1; on (default)
WEB-DISP
Use it to enable/disable the fixing web length warning message.
setting
0: off (do not display)
1: on (display; default)
If set to '0', the message will only be on the service mode screen.
W-TONER
Use it to enable/disable the collecting toner case full message.
setting
0: off (do not display)
1: on (display; default)
If set to '0', the message will be only on the service mode screen.
COUNTER1
Use it to set soft counter 1 of the user mode screen.
101: total 1 (fixed)
COUNTER2
Use it to set soft counter 2 of the user mode screen.
setting: 0 to 999
COUNTER3
Use it to set soft counter 3 of the user mode screen.
setting: 0 to 999
COUNTER4
Use it to set soft counter 4 of the user mode screen.
setting: 0 to 999
COUNTER5
Use it to set soft counter 5 of the user mode screen.
setting: 0 to 999
COUNTER6
Use it to set soft counter 6 of the user mode screen.
setting: 0 to 999
CONTROL
Not used
B4-L-CNT
Use it to specify where B4 should be counted as large or small size for soft counters 1 thorough 6.
0: count as small size (default)
1: count as large size
COPY-JOB
Use it to enable/disable copy job reservation with a card reader/coin vendor in use.
setting
0: enable copy job reservation (default)
1: disable copy job reservation
PR-PSESW
Use it to enable/disable the print pause function switch.
setting
0: disable print pause function (default)
1: enable print pause function (display print output stop/resume button on user screen)
IDPRN-SW
Use it to switch over count increment jobs for the group control counter.
0: for PRINT, increment the following: box print, report print, SEND local print, PDL print (default)
1: for PRINT, increment the following: report print, SEND local print, PDL print
CNT-SW
Use it to switch over display of charge counter default items.
setting
0: default total 1 (101; default)
1: default total 2 (102), copy total 2 (202), total A total 2 (127)
2: default total 1 (101), total small (104), total large (103), scan total 1 (501)
TAB-ACC
Use it to enable/disable automatic switchover of cassettes for tab (index) paper.
setting
0: do not change over between tab sheets (default)
1: change over between tab sheets
COPIER > OPTION > BODY
T-17-52
COPIER > OPTION >USER
Chapter 17
Level
2
2
2
2
2
Level
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
17-39
Advertisement
Chapters
Table of Contents
Troubleshooting
