Canon imageRUNNER 5065 series Service Manual page 545

Sub-item Description
CST-U1/U2/U3/ Use it to select paper names used in paper size groups.
U4 By setting any of the following special paper sizes for U1, U2, U3, and U4, these paper sizes may be recognized as special size
papers for the universal cassette in question.
setting
24: Foolscap (CST-U2; default)
25: Australian Foolscap
26: Oficio
27: Ecuadorian Officio
28: Bolivian Officio
29: Argentine Letter (U4; default)
30: Argentine Letter-R
31: Government Letter (U1; default)
32: Government Letter (U1; default)
32: Government Letter-R
34: Government Legal (U3; default)
35: Folio
36: Argentine Officio
37: Mexico Officio
38: Executive
<ACC>
Sub-item Description
COIN Use it to set the coin vendor mechanism.
setting
0: off
1: on
DK-P Use it to set the size of paper used in the Side Paper Deck.(for the Side Paper Deck AD1)
setting
0: A4 (default)
1: B5
2: LTR
CCV2CT Use it to enable/disable large 2 count control.
0: off (disable 2-count control; default)
1: on (enable 2-count control; count pulse width/pulse width, 100 msec)
2: on (enable 2-count control; count pulse width/pulse width, 30 msec)
CCV-LSZ Use it to set a threshold for small/large size identification used in large 2 count mode.
setting: 0 to 458 (default: 364; in mm)
PD-SIZE Setting size of the Side Paper Deck AE1 (displayed only the Side Paper Deck AE1 is mounted)
Normal size can be set with the user mode, and special size can be set with the service mode.
Setting Range: 0 to 37 [default: 0]
The value 0 or 22 to 37 can be set with the service mode.
If the setting value is 0 to 21, the value 1 to 21 can be input with the user mode.
CC-SPSW Use it to set control card I/F support.
0: do not support (default)
1: support
<INT-FACE>
Sub-item Description
IMG-CONT Use it to set the connection of the EFI controller.
setting
0: no controller
1: EFI model (PINATUBO, Mt. Hood)
2: T/R, AHT model
3: EFI external controller present (Yukon/Pinatubo V2.0)
4: EFI external controller present (Meru V3.1)
AP-OPT Use it to permit/not permit printing from application PrintMe built into the PS print server unit.
setting
0: permit printing using unspecific ID (default)
1: permit printing using specific account
2: reject printing
AP-ACCNT Use it to set (CPCA) group ID for printing (job) from application PrintMe built into the PS print server unit.
setting
0 to 9999999 (default: 0)
AP-CODE Use it to set the (CPCA) path for printing (job) from application PrintMe built into the PS print server unit.
setting
0 to 99999999 (default: 0)
<TEMPO>
Sub-item Description
F-POT-SW Use it to enable/disable settings in the event of a transfer fault caused by a fault in the potential sensor.
- Use it as a tentative remedy until the potential sensor is replaced.
settling
0: off (default); 1: on
COPIER > OPTION > CST
T-17-55
COPIER > OPTION > ACC
T-17-56
COPIER > OPTION > INT-FACE
T-17-57
COPIER > OPTION > TEMPO
Chapter 17
Level
2
Level
1
1
1
1
1
2
Level
1
2
2
2
Level
2
17-49