Error Code (Send) - Canon imageRUNNER 5065 series Service Manual

CHK-
XX Partition
TYPE
01 FSTDEV
02 1 IMG_MNG
03 FSTCDEV
04 APL_GEN
05 TMP_GEN
2
06 TMP_FAX
07 TMP_PSS
08 3 PDLDEV
09 4 BOOTDEV
10 5 APL_MEAP
11 6 APL_SEND
12 7 APL_KEEP
13 8 APL_LOG
Not
FF 0
identified
YY
*1
*2
An ongoing write operation
03
is interrupted (at start-up).
*3
*4
*5
*6
A file system error has
05
*7
*8
00
There is poor contact for the
01
*9 HDD, or there is a system
02
04
11 There is poor connection of
*10
21
13 A write operation has been
*11
25
10
12
14 There is a system error or a
*12
22
23
24

16.3 Error Code (SEND)

16.3.1 Results of Self-Diagnosis
iR5065 / iR 5055 / iR5075 / / /
XX
Description
compressed image data (e.g., Box)
file management table, profile
job archiving (chasing)
general data
general data (temporary file)
for fax (temporary file)
for PDL spool (temporary file)
for PDL spool (e.g., font)
firmware (system, MEAP, key, certificate,
PDF dictionary, RUI content, audio
dictionary)
MEAP application
address book, filter
MEAP save data
System log saving capacity
full check on HDD for faulty sector and
recovery
Description
1. Set '0' to CHK-TYPE, and execute HD-CHECK; then, turn off and then back on the power.
2. Type in CHK-TYPE that corresponds to the partition in question, and execute HD-CLEAR; then, turn off and
then back on the power.
1. Ask the user to download the address book data using a remote UI.
2. Set '0' to CHK-TYPE, and execute HD-CHECK; thereafter, turn off and then on the power.
3. Start download mode, and execute full formatting using the SST; thereafter, turn off and then back on the power.
The recovery operation for the boot partition necessarily requires the use of the SST in safe mode.
1. Set '0' for CHK-TYPE, and execute HD-CHECK; thereafter, turn off and then back on the power.
2. Start download mode, and execute full formatting and re-install the system software; thereafter, turn off and
then back on the power.
1. Set '0' to CHK-TYPE, and execute HD-CHECK; then, turn off and then back on the power.
2. Execute HD-CLEAR by setting '1', '2', '3', and '5' to CHK-type; then, turn off and then back on the power.
1. Type in CHK-TYPE corresponding to the partition in question, and execute HD-CLEAR; then, turn off and then
back on the power.
2. Replace the HDD, and re-install the system software.
The machine does not permit execution of HD-CLEAR in service mode (to prevent loss of partition information
such as address book and filter data).
1. Ask the user to download the address book data using a remote UI.
2. Start download mode from service mode; then, execute full formatting using
the SST, and re-install the system software. Thereafter, turn off and then back on the power.
occurred.
1. Execute HD-CLEAR by setting "1', '2', '3', and '5' to CHK-TYPE; then, turn off and then back on the power.
2. Replace the HDD, and re-install the system software.
Recovery operation for the Boot partition necessarily requires the use of the SST in safe mode.
1. Start in safe mode, and execute full formatting in the SST, and re-install the system software. Thereafter, turn
off and then on the power.
2. Replace the HDD, and re-install the system software.
1. Check the cables and power cord for disconnection.
2. Start up in safe mode; then, execute full formatting using the SST, and re-install the system software. Thereafter,
turn off and then back on the power.
error.
3. Replace the HDD, and re-install the system software.
1. Check the cable and the power connectors for disconnection.
the HDD. 2. Replace the HDD, and re-install the system software.
File data as of Box on the HDD may be damaged.
1. Set '0' for CHK-TYPE, and execute HD-CHECK; then, turn off and then back on the power.
2. Set '1' for CHK-TYPE, and execute HD-CLEAR.
suspended.
(In the case of APL_SEND or BOOTDEV, reformat using the SST and re-install the system software.)
3. Replace the HDD, and re-install the system software.
1. Start up in safe mode; then, execute full formatting using the SST, and re-install the system software. Thereafter,
turn off and then back on the power.
2. Replace the HDD, and re-install the system software.
packet data error.
T-16-4
At start-up
03 05 00,01,02,04
Remedy
*1 *5
*9
*3 *8
*1 *5
*2 *5
*3 *8
*1 *5
*4 *7
T-16-5
Remedy
Chapter 16
YY
During operation
11,2 13,2
10,12,14,22,23,24
1 5
Remedy
*10 *11 *12
0015-5628
16-11