After Replacing The Hdd; When Replacing The Main Controller Pcb; Points To Note When Mounting The Pickup Roller; Points To Note When Mounting The Separation Roller - Canon imageRUNNER 5065 series Service Manual

Chapter 14
[1]
14.7.2 When Replacing HVT PCB
iR5065 / iR 5055 / iR5075 / / /
Enter the values indicated on the label of the HVT PCB using the following
service mode items:
COPIER>ADJUST>HV-TR>H-PRE-TR
COPIER>ADJUST>HV-TR>HVT-TR
COPIER>ADJUST>HV-SP>HVT-SP
COPIER>ADJUST>DEVELOP>HVT-DE

14.7.3 After Replacing the HDD

iR5065 / iR 5055 / iR5075 / / /
- Formatting the HDD
Start up the machine in the safe mode (i.e., while holding down the 2 and 8
keys, turn on the main power).
Using the HD format function of the SST, format all partitions (BOOTDEV/
PDLDEV/FSTDEV/FSTCDEV/TMP_GEN/TMP_FAX/TMP_PSS/
IMG_MNG/APL_MEAP/APL_GEN/APL_SEND). (For details, see the de-
scriptions given for upgrading.)
- Downloading the system software
Using the SST, download the following: System, Language, RUI, MEAP-
CONT (Meap content), SDICT (OCR dictionary), KEY (key/certificate for
encrypted communication), TTS (audio dictionary).

14.7.4 When Replacing the Main Controller PCB

iR5065 / iR 5055 / iR5075 / / /
Upload each setting/registration data stored in SRAM of the main controller
PCB onto the PC by using SST. See the chapter 'Version Upgrading' for its
operation procedure.
If you are replacing the main controller PCB, be sure to transfer the follow-
ing components from the old to new PCB.
[2]
[1] Boot ROM
[2] Hard disk
[3] Image memory (SDRAM)
[4] Counter memory PCB
14.8 Pickup/Feeding System

14.8.1 Points to Note When Mounting the Pickup Roller

iR5065 / iR 5055 / iR5075 / / /
14-22
[2]
F-14-58
[4]
[1]
[3]
F-14-59
Å°The direction of the mounting pickup roller
The pickup roller may be mounted by reversing the steps used to remove it;
however, be sure to keep the following in the mind.
- The roller used at the front and the rear of the machine is not compatible.
- When mounting the pickup roller used at the front of the machine [1],
make sure the round mark [2] and the punch mark [3] found on the side
of the roller are toward the front of the machine.
Direction of
rotation
[1]
- When mounting the pickup roller used at the rear of the machine [1],
0015-9990
make sure the punch mark [2] is at the rear of the machine.
Direction of
rotation
0016-0002
[1]
14.8.2 Points to Note When Mounting the Separation
Roller
iR5065 / iR 5055 / iR5075 / / /
When replacing the separation roller, be sure it is oriented as follows.
Mounting the separation roller in a wrong orientation may lead to interfer-
ence against the crimping washer. Make sure it is mounted in a correct ori-
0016-0011
entation.
Cassette 1/2, Right deck pickup assembly
Wider groove
Left deck pickup assembly

14.8.3 The Points to Mount the Feeding Roller

iR5065 / iR 5055 / iR5075 / / /
0016-0017
When mounting the feeding roller [1] to the cassette pickup assembly, make
[2]
[3]
Front side of
the machine
F-14-60
[2] [2]
Rear side of
the machine
F-14-61
Narrower groove
(rear of machine)
(front of machine)
F-14-62
Narrow groove
Wider groove
F-14-63
0016-0019
0016-0021