Chrysler 1997 Stratus Convertible RHD Service Manual page 185

JX
REMOVAL AND INSTALLATION (Continued)
(2) Install wheel speed sensor attaching bolt (Fig.
40). Tighten the speed sensor head attaching bolt to
8 N·m (75 in. lbs.)
(3) Install speed sensor cable routing clips (Fig.
39) on the brake flex hose bracket and the bracket on
the upper control arm. Install and securely tighten
the routing clip attaching bolts.
(4) Install connector end of speed sensor cable
through hole in inner fender and into trunk of vehi-
cle.
(5) Install speed control sealing grommet into hole
in inner fender. Install the sealing grommet retainer
and attaching bolt (Fig. 38) on rear frame rail.
Securely tighten retainer attaching bolt.
(6) Install the tire and wheel assembly on vehicle.
(7) Lower vehicle.
(8) Plug speed sensor cable connector into vehicle
wiring harness (Fig. 37). Install foam sleeve back
over the speed sensor cable to vehicle wiring
harness connection to prevent connector from
rattling against body of vehicle.
(9) Road test vehicle to ensure proper operation of
the base and ABS systems.
SPECIFICATIONS
SPEED SENSOR TONE WHEEL RUNOUT
The total indicator runout allowed for both the
front and rear tone wheel measured using a dial indi-
cator is 0.15 mm (.006 in.).
WHEEL SPEED SENSOR TO TONE WHEEL
CLEARANCE
FRONT WHEEL
Minimum Clearance .35mm (.014 in.)
Maxamum Clearance 1.2 mm (.047 in.)
REAR WHEEL
Minimum Clearance .40mm (.016 in.)
Maxamum Clearance 1.2 mm (.047 in.)
BRAKE FASTENER TORQUE SPECIFICATIONS
DESCRIPTION
BRAKE TUBES:
Tube Nuts To Fittings And
Components . . . . . . . . . . . 20 N·m (180 in. lbs.)
BRAKE HOSE:
Front Caliper Banjo Bolt . . . . . 48 N·m (35 ft. lbs.)
Rear Intermediate Bracket . . 11 N·m (100 in. lbs.)
Front And Rear Brackets To
Frame Rails . . . . . . . . . . . . 10 N·m (95 in. lbs.)
MASTER CYLINDER:
To Vacuum Booster Mounting
Nut . . . . . . . . . . . . . . . . . . 28 N·m (250 in. lbs.)
BRAKE BOOSTER:
To Dash Panel Mounting Nuts . 37 N·m (27 ft. lbs.)
BRAKE PEDAL
To Dash Panel Plenum Mounting
Nut . . . . . . . . . . . . . . . . . . . 37 N·m (27 ft. lbs.)
Shaft To Brake Pedal Bracket
Nut . . . . . . . . . . . . . . . . . . . 34 N·m (25 ft. lbs.)
REAR WHEEL CYLINDER:
To Support Plate Mounting
Bolts . . . . . . . . . . . . . . . . . 13 N·m (115 in. lbs.)
Bleeder Screw . . . . . . . . . . . . . 10 N·m (90 in. lbs.)
BRAKE SUPPORT PLATE:
To Axle Mounting Bolts . . . . . . 75 N·m (55 ft. lbs.)
DISC BRAKE CALIPER:
Guide Pin Bolts . . . . . . . . . . . . 22 N·m (16 ft. lbs.)
Bleeder Screw . . . . . . . . . . . . . 20 N·m (15 ft. lbs.)
ABS HYDRAULIC CONTROL UNIT:
To Mounting Bracket Bolts . . 28 N·m (250 in. lbs.)
Bracket To Crossmember
Mounting Bolts . . . . . . . . . . 28 N·m (250 in. lbs.)
PARKING BRAKE:
Lever Mounting Nuts . . . . . . . 24 N·m (18 ft. lbs.)
REAR HUB AND BEARING:
To Knuckle Retaining Nut . . 250 N·m (185 ft. lbs.)
WHEEL:
Stud Lug Nut . . . . . 115–155 N·m (85–115 ft. lbs.)
BRAKES 5 - 83
TORQUE