D-Link DXS-1210-12TC Reference Manual page 49

host SRC-IP-ADDR
SRC-IP-ADDR SRC-IP-
WILDCARD
host DST-IP-ADDR
DST-IP-ADDR DST-IP-
WILDCARD
precedence PRECEDENCE
dscp DSCP
tos TOS
lt PORT
gt PORT
eq PORT
neq PORT
range MIN-PORT MAX-PORT
TCP-FLAG
fragments
time-range PROFILE-NAME
tcp, udp, igmp, ipinip, gre,
esp, eigrp, ospf, pcp, pim,
vrrp
PROTOCOL-ID
ICMP-TYPE
ICMP-CODE
ICMP-MESSAGE
Default
DXS-1210 Series Smart Managed Switch CLI Reference Guide
Specifies a specific source host IP address.
Specifies a group of source IP addresses by using a wildcard bitmap.
The bit corresponding to the bit value 1 will be ignored. The bit
corresponding to the bit value 0 will be checked.
Specifies a specific destination host IP address.
Specifies a group of destination IP addresses by using a wildcard
bitmap. The bit corresponding to the bit value 1 will be ignored. The bit
corresponding to the bit value 0 will be checked.
(Optional) Specifies that packets can be filtered by precedence level,
as specified by a number from 0 to 7.
(Optional) Specifies the matching DSCP code in IP header. The range
is from 0 to 63, or select the following DSCP name: af11 - 001010,
af12 -001100, af13 - 001110, af21 - 010010, af22 - 010100, af23 -
010110, af31 - 011010, af32 - 011100, af33 - 011110, af41 - 100010,
af42 - 100100, af43 - 100110, cs1 - 001000, cs2 - 010000, cs3 -
011000, cs4 - 100000, cs5 - 101000, cs6 - 110000, cs7 - 111000,
default - 000000, ef – 101110.
(Optional) Specifies that packets can be filtered by type of service
level, as specified by a number from 0 to 15.
(Optional) Specifies to match if less than the specified port number.
(Optional) Specifies to match if greater than the specified port number.
(Optional) Specifies to match if equal to the specified port number.
(Optional) Specifies to match if not equal to the specified port number.
(Optional) Specifies to match if fall within the range of ports.
(Optional) Specifies the TCP flag fields and the specified TCP header
bits calledack (acknowledge), fin (finish), psh (push), rst (reset), syn
(synchronize), or urg (urgent).
(Optional)Specifies the packet fragment's filtering.
(Optional) Specifies the name of the timeperiod profile associated with
the accesslist delineating its activation period.
Specifies Layer 4 protocols.
(Optional) Specifies the protocol ID. The valid value is from 0 to 255.
(Optional) Specifies the ICMP message type. The valid number for the
message type is from 0 to 255.
(Optional) Specifies the ICMP message code. The valid number for the
message code is from 0 to 255.
(Optional) Specifies the ICMP message. The pre-defined parameters
are available for selection: administratively-prohibited,alternate-
address,conversion-error,host-prohibited,net-prohibited,echo,echo-
reply,pointer-indicates-error,host-isolated,host-precedence-
violation,host-redirect,host-tos-redirect,host-tos-unreachable,host-
unknown,host-unreachable, information-reply,information-
request,mask-reply,mask-request,mobile-redirect,net-redirect,net-tos-
redirect,net-tos-unreachable, net-unreachable,net-unknown,bad-
length,option-missing,packet-fragment,parameter-problem,port-
unreachable,precedence-cutoff, protocol-unreachable,reassembly-
timeout,redirect-message,router-advertisement,router-
solicitation,source-quench,source-route-failed, time-
exceeded,timestamp-reply,timestamp-request,traceroute,ttl-
expired,unreachable.
46