H: Terminal Functions; H: Terminal Functions; H1: Multi-Function Digital Inputs - YASKAWA P1000 Technical Manual

5.7

H: Terminal Functions

H parameters assign functions to the external terminals.
u

H1: Multi-Function Digital Inputs

n H1-01 to H1-08: Functions for Terminals S1 to S8
These parameters assign functions to the multi-function digital inputs. The various functions and settings are listed in
5.29.
No.
H1-01 Multi-Function Digital Input Terminal S1 Function Selection
H1-02 Multi-Function Digital Input Terminal S2 Function Selection
H1-03 Multi-Function Digital Input Terminal S3 Function Selection
H1-04 Multi-Function Digital Input Terminal S4 Function Selection
H1-05 Multi-Function Digital Input Terminal S5 Function Selection
H1-06 Multi-Function Digital Input Terminal S6 Function Selection
H1-07 Multi-Function Digital Input Terminal S7 Function Selection
H1-08 Multi-Function Digital Input Terminal S8 Function Selection
<1> Number appearing in parenthesis is the default value after performing a 3-Wire initialization (A1-03 = 3330).
Setting
0 3-Wire Sequence
1 LOCAL/REMOTE Selection
2 External Reference 1/2 Selection
3 Multi-Step Speed Reference 1
4 Multi-Step Speed Reference 2
5 Multi-Step Speed Reference 3
6 Jog reference Selection
7 Accel/Decel Time Selection 1
8 Baseblock Command (N.O.)
9 Baseblock Command (N.C.)
A Accel/Decel Ramp Hold
B Drive Overheat Alarm (oH2)
C Analog Terminal Input Selection
F Through Mode
10 Up Command
11 Down Command
12 Forward Jog
13 Reverse Jog
14 Fault Reset
15 Fast Stop (N.O.)
17 Fast Stop (N.C.)
18 Timer Function Input
19 PID Disable
1A Accel/Decel Time Selection 2
1B Program Lockout
1E Reference Sample Hold
20 to 2F External Fault
30 PID Integral Reset
31 PID Integral Hold
YASKAWA SIEP YAIP1U 01C AC Drive - P1000 Technical Manual
Parameter Name
Table 5.29 Multi-Function Digital Input Terminal Settings
Function
Setting
Range
1 to 9F
40 (F)
1 to 9F
41 (F)
0 to 9F 24: External Fault
0 to 9F 14: Fault Reset
<1>
0 to 9F
3 (0)
<1>
0 to 9F
4 (3)
<1>
0 to 9F
6 (4)
<1>
0 to 9F
8: (6)
Page Setting
206 32 Multi-Step Speed Reference 4
206 34 PID Soft Starter Cancel
207 35 PID Input Level Selection
40 Forward Run Command (2-Wire sequence)
207 41 Reverse Run Command (2-Wire sequence)
42 Run Command (2-Wire sequence 2)
207 43 FWD/REV Command (2-Wire sequence 2)
207 47 Node Setup
51 Disable Sequence Timers
207
52 Cancel Active Sequence Timer
207 60 DC Injection Braking Command
208 61 External Speed Search Command 1
208 62 External Speed Search Command 2
208 63 Field Weakening
65 KEB Ride-Thru 1 (N.C.)
208
66 KEB Ride-Thru 1 (N.O.)
67 Communications Test Mode
209
68 High Slip Braking (HSB)
209 6A Drive Enabled
209 75 Up 2 Command
209 76 Down 2 Command
210 7A KEB Ride-Thru 2 (N.C.)
210 7B KEB Ride-Thru 2 (N.O.)
210 A8 Secondary PI Disable (N.O.)
210 A9 Secondary PI Disable (N.C.)
210 AA Secondary PI Inverse Operation
211 AB Secondary PI Integral Reset
211 AC Secondary PI Integral Hold
211 AD Select Secondary PI Parameters

5.7 H: Terminal Functions

Default
<1>
: Forward Run Command (2-Wire sequence)
<1>
: Reverse Run Command (2-Wire sequence)
: Multi-Step Speed Reference 1
: Multi-Step Speed Reference 2
: Jog Reference Selection
: External Baseblock Command
Function
Table
Page
211
211
211
212
212
212
212
212
212
212
212
213
5
213
213
213
213
213
214
214
214
214
214
214
215
205