YASKAWA P1000 Technical Manual page 586

Index
oH2 ............................................................................... 315
oH3 ............................................................................... 315
oH4 ............................................................................... 316
oH5 ............................................................................... 303
oH Alarm Location Monitor .................................................. 484
oL1................................................................................ 303
oL2................................................................................ 304
oL2 Characteristics Selection at Low Speeds......................... 260, 467
oL3................................................................................ 304
oL4................................................................................ 305
oL7................................................................................ 305
oPE ............................................................................... 319
oPE01 ............................................................................ 319
oPE02 ............................................................................ 319
oPE03 ............................................................................ 319
oPE04 ............................................................................ 320
oPE05 ............................................................................ 320
oPE07 ............................................................................ 320
oPE09 ............................................................................ 321
oPE10 ............................................................................ 321
oPE11 ............................................................................ 321
oPE28 ............................................................................ 321
oPE Fault Parameter............................................................ 480
Operating with the Load Connected.......................................... 136
Operation Errors .......................................................... 291, 294
Operation Selection when Digital Operator is Disconnected ....... 271, 471
Operation Status Monitors..................................................... 286
Operator Programming Errors ................................................ 319
Operator Related Settings...................................................... 267
Operator RUN Save at Power Loss .................................... 271, 471
oPr ................................................................................ 305
Optional 24 V DC power supply connector cover .... 36, 37, 38, 39, 40, 41
Option card connection error (CN5-A) ...................................... 301
Option Card Connection Error at Option Port CN5-A..................... 301
Option Card Connection Error at Option Port CN5-C..................... 302
Option card connector (CN5-A) ................................................44
Option card connector (CN5-B) ................................................44
Option card connector (CN5-C) ................................................44
Option card error occurred at option port CN5-A .......................... 301
Option card error occurred at option port CN5-B .......................... 302
Option card error occurred at option port CN5-C .................... 302, 303
Option Card External Fault.............................................. 297, 313
Option Card Fault at Option Port CN5-A ................................... 301
Option Card Fault at Option Port CN5-B.............................. 301, 302
Option Card Fault at Option Port CN5-C.................................... 302
Option Communication Error ........................................... 295, 311
Option Frequency Reference .................................................. 484
Option Installation .............................................................. 378
Option Settings.................................................................. 198
Oscillation or Hunting.......................................................... 334
Output Current .................................................................. 479
Output Current 1 During Speed Search...................................... 157
Output Current at Previous Fault ............................................. 481
Output Current Imbalance ..................................................... 300
Output Frequency............................................................... 479
Output Frequency after Soft Start ............................................ 480
Output Frequency at Previous Fault.......................................... 481
Output Frequency Reduction During Overheat Alarm .................... 259
Output Frequency Resolution ................................................. 403
Output Ground Fault Detection Selection ............................. 260, 467
586
Output Phase Loss .............................................................. 299
Output Phase Loss Detection Lvl for Dynamic Noise Control ........... 285
Output Phase Loss Level for Dynamic Noise Control..................... 276
Output Phase Loss Protection ................................................. 467
Output Phase Loss Protection Selection ..................................... 259
Output Power.................................................................... 479
Output Power at Previous Fault............................................... 481
Output Terminal Status ........................................................ 479
Output Terminal Status at Previous Fault ................................... 481
Output Voltage at Previous Fault ............................................. 481
Output Voltage Detection Fault............................................... 310
Output Voltage Reference ..................................................... 479
ov............................................................................ 305, 316
Overcurrent ...................................................................... 300
Overexcitation Deceleration................................................... 249
Overexcitation Deceleration Gain ...................................... 266, 469
Overexcitation Operation Selection .................................... 266, 469
Overheat 1 (Heatsink Overheat) .............................................. 303
Overheat Alarm Level.................................................... 258, 467
Overheat Pre-Alarm Operation Selection ............................. 258, 467
Overload Protection ............................................................ 403
Overload Tolerance................... 394, 395, 396, 397, 398, 400, 401, 402
Overtorque Detection 1 ........................................................ 304
Overtorque Detection 2 ........................................................ 305
Overtorque Detection Operation.............................................. 256
Overvoltage...................................................................... 305
Overvoltage Protection......................................................... 403
Overvoltage Suppression Function ........................................... 250
Overvoltage Suppression Function Selection ............................... 250
ov Suppression Function Selection........................................... 465
P
P1000 Models .....................................................................29
Parameter Access Level........................................................ 137
Parameter Range Setting Error................................................ 319
Parameter Settings .............................................................. 118
Parameters for KEB Ride-Thru ............................................... 244
Parameters to Minimize Motor Hunting and Oscillation .................. 290
PASS ............................................................................. 316
Password ................................................................... 137, 143
Password Setting................................................................ 143
Password Settings............................................................... 137
Peak Hold Current .............................................................. 484
Peak Hold Output Frequency ................................................. 484
Performance Life ............................................................ 343, 3
Performance Life Monitors Maintenance Monitors........................... 3
Periodic Inspection ............................................................. 341
Periodic Maintenance .......................................................... 222
PF ................................................................................. 306
Phase Order Selection .......................................................... 152
PID Accel/Decel Time ......................................................... 167
PID Block Diagram............................................................. 163
PID Control...................................................................... 160
PID Feedback 1 ................................................................. 485
PID Feedback High Detection Level......................................... 167
PID Feedback High Detection Time ......................................... 167
PID Feedback Input Methods ................................................. 161
PID Feedback Loss ....................................................... 299, 314
PID Feedback Loss Detection Selection..................................... 166
PID Feedback Low Detection Level ......................................... 166
YASKAWA SIEP YAIP1U 01C AC Drive - P1000 Technical Manual