H: Terminal Functions; H: Terminal Functions; H1: Multi-Function Digital Inputs - YASKAWA Z1000 CIMR-ZU*A Series Programming Manual

1.7 H: Terminal Functions

1.7

H: Terminal Functions

H parameters assign functions to the external terminals.
u

H1: Multi-Function Digital Inputs

n H1-01 to H1-07: Functions for Terminals S1 to S7
These parameters assign functions to the multi-function digital inputs. The various functions and settings are listed in
1.28.
No.
H1-01 Multi-Function Digital Input Terminal S1 Function Selection
H1-02 Multi-Function Digital Input Terminal S2 Function Selection
H1-03 Multi-Function Digital Input Terminal S3 Function Selection
H1-04 Multi-Function Digital Input Terminal S4 Function Selection
H1-05 Multi-Function Digital Input Terminal S5 Function Selection
H1-06 Multi-Function Digital Input Terminal S6 Function Selection
H1-07 Multi-Function Digital Input Terminal S7 Function Selection
<1> Number appearing in parenthesis is the default value after performing a 3-Wire initialization.
Setting
0 3-Wire Sequence
3 Multi-Step Speed Reference 1
4 Multi-Step Speed Reference 2
6 Jog reference Selection
7 Accel/Decel Time Selection 1
8 Baseblock Command (N.O.)
9 Baseblock Command (N.C.)
A Accel/Decel Ramp Hold
B Drive Overheat Alarm (oH2)
C Analog Terminal Input Selection
F Through Mode
10 Up Command
11 Down Command
12 Forward Jog
13 Reverse Jog
14 Fault Reset
15 Fast Stop (N.O.)
17 Fast Stop (N.C.)
18 Timer Function Input
19 PID Disable
1B Program Lockout
1E Reference Sample Hold
20 to 2F External Fault
30 PID Integral Reset
31 PID Integral Hold
34 PID Soft Starter Cancel
35 PID Input Level Selection
40 Forward Run Command (2-Wire sequence)
41 Reverse Run Command (2-Wire sequence)
72
Parameter Name
Table 1.28 Multi-Function Digital Input Terminal Settings
Function
Setting
Range
1 to B2
40 (F)
1 to B2
41 (F)
0 to B2 24: External Fault
0 to B2 14: Fault Reset
<1>
0 to B2
3 (0)
<1>
0 to B2
4 (3)
<1>
0 to B2
6 (4)
Page Setting
73 42 Run Command (2-Wire sequence 2)
43 FWD/REV Command (2-Wire sequence 2)
73
44 Offset Frequency 1
73 45 Offset Frequency 2
74 46 Offset Frequency 3
47 Node Setup
74
49
GF1 Error (N.O., N.C.)
74 4A
74 50 Motor Pre-Heat 2
74 51 Sequence Timer Disable
74 52 Sequence Timer Cancel
60 Motor Pre-Heat 1
75
61 External Speed Search Command 1
62 External Speed Search Command 2
76
63 Field Weakening
76 65 KEB Ride-Thru 1 (N.C.)
76 66 KEB Ride-Thru 1 (N.O.)
76 67 Communications Test Mode
76 68 High Slip Braking
77 69 Jog 2
77 6A Drive Enabled
77 6D AUTO Mode Select
77 6E HAND Mode Select
78 70 Drive Enable2
78 7A KEB Ride-Thru 2 (N.C.)
78 7B KEB Ride-Thru 2 (N.O.)
78 7C Short Circuit Braking (N.O.)
7D Short Circuit Braking (N.C.)
78
A4 Emergency Override
A5 BP Drive/Bypass Selection
YASKAWA SIEP YAIZ1U 03B YASKAWA AC Drive – Z1000 Programming Manual
Default
<1>
: Forward Run Command (2-Wire sequence)
<1>
: Reverse Run Command (2-Wire sequence)
: Multi-Step Speed Reference 1
: Multi-Step Speed Reference 2
: Jog Reference Selection
Function
Table
Page
78
79
79
79
79
79
79
79
79
79
79
80
80
80
80
80
80
80
81
81
81
81
81