YASKAWA P1000 Technical Manual page 587

PID Feedback Low Detection Time.......................................... 166
PID Fine Tuning ................................................................ 174
PID Function Setting ........................................................... 164
PID Input (feedback) ........................................................... 485
PID Input Limit ................................................................. 172
PID Monitors .................................................................... 286
PID Offset Adjustment......................................................... 164
PID Output....................................................................... 485
PID Output Gain Setting....................................................... 165
PID Output Level Selection ................................................... 165
PID Output Limit ............................................................... 164
PID Output Lower Limit....................................................... 172
PID Output Reverse Selection ................................................ 165
PID Output Reverse Selection 2 .............................................. 174
PID Primary Delay Time Constant ........................................... 164
PID Setpoint ..................................................................... 485
PID Setpoint Display Digits................................................... 170
PID Setpoint Input Methods................................................... 161
PID Setpoint Scaling ........................................................... 169
PID Setpoint Selection ......................................................... 168
PID Setpoint User Display .................................................... 170
PID Setpoint Value ............................................................. 168
PID Sleep ........................................................................ 167
PID Sleep Delay Time ......................................................... 167
PID Sleep Function Start Level ............................................... 167
PI Output 2 Monitor Max Upper/Lower 4 Digits .......................... 173
PI Output 2 Monitor Minimum ............................................... 173
PI Output Monitor Calculation Method...................................... 173
PI Setpoint Monitor Unit Selection........................................... 170
PI Unit Selection ................................................................ 172
Power Detection Filter Time .................................................. 176
Powering Up the Drive......................................................... 125
Power Ratings (Three-Phase 200 V Class)...................... 394, 395, 396
Power Ratings (Three-Phase 400 V Class)...................... 397, 398, 399
Power Ratings (Three-Phase 600 V Class)...................... 400, 401, 402
Power Unit Output Phase Loss 3 ............................................. 300
Predefined V/f Patterns ........................................................ 192
Preface..............................................................................16
Preparing the Ends of Shielded Cables ........................................99
Preset Reference Timing Diagram ........................................... 184
Previous Fault ................................................................... 481
PROFIBUS-DP Clear Mode Selection ...................................... 202
PROFIBUS-DP Data Format Selection...................................... 202
PROFIBUS-DP Node Address ............................................... 202
PROFIBUS-DP Parameters ................................................... 202
Programmable Run Timers for Real Time Clock (RTC).................. 276
Programming Mode ...................................................... 114, 118
Proportional Gain Setting (P) ................................................. 164
Protective Cover ..................................................................50
Protective Covers, Reattaching .................................................78
Protective Covers, Removing .............................................. 77, 78
Protective cover to prevent miswiring .........................................44
PTC ............................................................................... 230
Pulse Train Input................................................................ 232
Pulse Train Input Bias.......................................................... 232
Pulse Train Input Filter Time ................................................. 232
Pulse Train Input Gain ......................................................... 232
Pulse Train Input Minimum Frequency...................................... 233
Pulse Train Input Scaling ...................................................... 232
Pulse Train Input Terminal RP Function Selection ........................ 232
YASKAWA SIEP YAIP1U 01C AC Drive - P1000 Technical Manual
R
R-....................................................................................97
R/L1 ................................................................................83
R+ ...................................................................................97
R1-L11 .............................................................................83
Radiated and Radio Frequency Noise........................................ 388
Ramp to stop .................................................................... 149
Rated Current Depending on Carrier Frequency ........................... 426
Rated Current Setting Alarm .................................................. 322
Rated Output Capacity ............... 394, 395, 396, 397, 398, 400, 401, 402
Rated Output Current................. 394, 395, 396, 397, 398, 400, 401, 402
Rated Slip Error ................................................................. 324
Rated Voltage, Rated Frequency ... 394, 395, 396, 397, 398, 400, 401, 402
rdEr ............................................................................... 326
READ ............................................................................ 272
rEAd .............................................................................. 326
Reading Drive MEMOBUS/Modbus Register Contents .................. 518
Reading Parameter Settings ................................................... 326
Real Time Clock ................................................................ 276
Reattaching the Digital Operator ...............................................79
Reattaching the Front Cover ....................................................81
Reattaching the Protective Cover...............................................82
Reattaching the Terminal Cover ........................................... 77, 78
REMOTE ........................................................................ 122
Removing the Cooling Fan .................................................... 349
Removing the Digital Operator .................................................79
Removing the Front Cover ......................................................79
Removing the Protective Cover.................................................82
Removing the Terminal Cover............................................. 77, 78
Replacement Parts .............................................................. 343
Replacing the Drive ............................................................ 371
Reset Communication Parameters............................................ 200
RESET Key...................................................................... 109
Resistance Tuning Error ....................................................... 322
Response Messages from Drive to Master .................................. 515
Reverse Direction Output Example Time Chart............................ 222
Reverse Operation Selection .................................................. 151
Reverse Prohibited Error....................................................... 324
rF .................................................................................. 306
rH ................................................................................. 306
Rotational Auto-Tuning........................................................ 130
Rotational Auto-Tuning for V/f Control..................................... 129
RP ...................................................................................96
rr................................................................................... 307
RS-422 Interface ................................................................ 510
RS-485 Interface ................................................................ 509
RTS Control Selection ......................................................... 512
Rubber Bushing ...................................................................36
rUn ................................................................................ 317
Run Command/Frequency Reference Source Selection Error............ 320
Run Command at Power Up................................................... 152
Run Command Method Selection ............................................ 513
Run Command Selection 1 .............................................. 148, 434
Run Command Selection 2 .................................................... 152
Run command selection while in Programming Mode .................... 151
Run Command Source Selection ............................................. 484
RUN Key ........................................................................ 109
RUN LED........................................................................ 111
RUN Light ....................................................................... 109
Index
587