YASKAWA P1000 Technical Manual page 585

Model Number and Nameplate Check .........................................31
Modes ............................................................................ 114
Momentary Overcurrent Protection .......................................... 403
Momentary Power Loss Minimum Baseblock Time................. 245, 463
Momentary Power Loss Operation Selection ......................... 157, 463
Momentary Power Loss Ride-Thru .................................... 240, 404
Momentary Power Loss Ride-Thru Time ............................. 245, 463
Momentary Power Loss Voltage Recovery Ramp Time ............ 246, 463
Monitor Output....................................................................96
Monitor Parameters....................................................... 230, 479
Most Recent Fault .............................................................. 482
Motor 1 Parameters............................................................. 195
Motor Acceleration Time for Inertia Calculations ................... 252, 465
Motor Base Frequency ............................................. 131, 133, 478
Motor Base Speed ........................................................ 133, 478
Motor Data Error................................................................ 323
Motor Direction at Power Up when Using Operator................. 271, 471
Motor Does Not Rotate ........................................................ 330
Motor Hunting and Oscillation Control Parameters ....................... 290
Motor Iron-Core Saturation Coefficient ..................................... 322
Motor Iron Loss ........................................................... 133, 478
Motor Iron Loss for Torque Compensation ................................. 196
Motor is Too Hot ............................................................... 331
Motor Leakage Inductance .................................................... 196
Motor Line-to-Line Resistance ............................................... 196
Motor No-Load Current........................................................ 196
Motor Overheat ................................................................. 315
Motor Overheat (NTC Input) ................................................. 303
Motor Overheat Alarm Operation Selection .......................... 237, 463
Motor Overheat Fault (PTC Input) ........................................... 316
Motor Overheat Fault Operation Selection............................ 237, 463
Motor Overload ................................................................. 303
Motor Overload Estimate (oL1) .............................................. 484
Motor Overload Protection Selection ............................ 222, 463, 564
Motor Overload Protection Time ................................. 236, 463, 565
Motor Performance Fine-Tuning ............................................. 136
Motor Poles...................................................................... 131
Motor Produces Insufficient Torque ......................................... 335
Motor Protection ................................................................ 234
Motor Protection Using a Positive Temperature Coefficient Thermistor ... 230
Motor PTC Characteristics .................................................... 237
Motor Rated Current ......................................... 133, 195, 478, 564
Motor Rated Power ................................................. 132, 196, 478
Motor Rated Slip................................................................ 195
Motor Rated Voltage ..................................................... 132, 478
Motor Rotates in One Direction Only........................................ 331
Motor Secondary Current (Iq) ................................................ 485
Motor Speed Fault .............................................................. 324
Motor Stalls During Acceleration or With Large Loads .................. 332
Motor Switch during Run...................................................... 317
Motor Temperature (NTC ..................................................... 484
Motor Temperature Input Filter Time.................................. 238, 463
Motor Underload................................................................ 308
Motor Underload Protection Level at Minimum Frequency .............. 257
Motor Underload Protection Selection....................................... 257
Motor Wiring......................................................................93
Mounting Hole .........................................37, 38, 39, 40, 41, 42, 43
Mounting hole.....................................................................36
Multi-Function Analog Input Selection Error............................... 320
Multi-Function Analog Input Terminal Settings ........................... 225
YASKAWA SIEP YAIP1U 01C AC Drive - P1000 Technical Manual
Multi-Function Analog Outputs .............................................. 230
Multi-Function Analog Output Terminal AM Bias ........................ 230
Multi-Function Analog Output Terminal AM Gain........................ 230
Multi-Function Analog Output Terminal AM Monitor Selection........ 230
Multi-Function Analog Output Terminal AM Signal Level Selection .. 231
Multi-Function Analog Output Terminal FM Bias......................... 230
Multi-Function Analog Output Terminal FM Gain ........................ 230
Multi-Function Analog Output Terminal FM Monitor Selection ........ 230
Multi-Function Analog Output Terminal FM Signal Level Selection... 231
Multi-Function Digital Inputs ...................................................95
Multi-Function Digital Input Terminal Settings ............................ 205
Multi-Function Digital Output ..................................................96
Multi-Function Digital Output Terminal Settings .......................... 215
Multi-Function Input Selection Error ........................................ 319
Multiple Drive Installation ......................................................49
Multiple Drive Wiring ...........................................................93
Multi-Step Speed Selection.................................................... 148
N
n1-02.............................................................................. 290
Nameplate..........................................................................31
ndAT.............................................................................. 325
NetRef/ComRef Function Selection.......................................... 200
Network Termination .......................................................... 508
No-Load Current Alarm ....................................................... 323
No-Load Current Error......................................................... 323
No-Load Operation ............................................................. 134
No-Load Operation Test Run ................................................. 134
Notes on Rotational Auto-Tuning ............................................ 130
Notes on Stationary Auto-Tuning ............................................ 130
nSE ............................................................................... 300
Number of Auto Restart Attempts...................................... 254, 466
Number of Motor Poles ............................................ 133, 196, 478
Number of Run Commands ................................................... 483
Number of Run Commands Counter Initialization......................... 274
Number of Speed Search Restarts ............................................ 159
O
o2-03.............................................................................. 137
oC ................................................................................. 300
oFA00 ............................................................................ 301
oFA01 ............................................................................ 301
oFA03 to oFA06 ................................................................ 301
oFA10 ............................................................................ 301
oFA11 ............................................................................ 301
oFA12 to oFA17 ................................................................ 301
oFA30 to oFA43 ................................................................ 301
oFb00 ............................................................................. 301
oFb01 ............................................................................. 302
oFb02 ............................................................................. 302
oFb03 to oFb11 ................................................................. 302
oFb12 to oFb17 ................................................................. 302
oFC00 ............................................................................ 302
oFC01 ............................................................................ 302
oFC02 ............................................................................ 302
oFC03 to oFC11 ................................................................ 302
oFC12 to oFC17 ................................................................ 302
oFC50 to oFC55 ................................................................ 303
oH ........................................................................... 303, 315
oH1 ............................................................................... 303
Index
585