Olivetti d-Color MF4003 Service Manual page 499

d-Color MF4003/MF3303
Error Catego Contents of error
code ry
remote station, the MCF
(reception check
response) cannot be
received.
T36 A DCN is received when
the remote station is
disconnected first during
RR/RNR sequence
continuing.
Example: Since an error
occurred during image
data processing on the
remote station
T38 F-Code Received unexpected
TX protocol from the remote
station during F code
polling TX
9.16 T4#
Error Catego Contents of error
code ry
T40 Sendin Fax soft error
g
T42 Non- Large amount of error
ECM lines in image data on
sendin the remote station
g Example: At time of
(Ph.D) Non-ECM
communication, if the
specified amount of error
lines is exceeded, PIP/
PIN may be received
instead of the resending
request.
T43 Sendin Received request for
g V.21 signal
retransmission (CRP)
three times continuously
Example: The remote
station cannot detect
retransmission signal.
T44 Unable to receive image
data from the main body
T48 Mismatched dialed
number and the
telephone number
information (CSI) set on
the remote station
device when enabling
the destination check
function.
Example: No telephone
number (local ID) has
been set on the remote
Y119930-3
How to correct
3. Increase the number of times for resending the post
message command.
4. Possibility of line defect (Wrong control of signal analysis
by exchangers)
1. Set the transmission beginning speed to V.29-9600bps.
2. Extend V.21 signals interval.
• Increase by +20 ms.
* If no effect is obtained, return the setting.
3. Possibility of line defect (Wrong control of signal analysis
by exchangers)
It cannot be dissolved by settings, so acquire a log.
(since an error may occur on the DIS received from the
remote station or altered by exchangers in midway)
• Protocol trace list for errors (including remote station)
• Line information for both fax machine and remote
station
• Machine management list (CSV save), activity report
How to correct
It cannot be dissolved by settings, so acquire a log.
(since an error may occur on the DIS received from the
remote station or altered by exchangers in midway)
• Protocol trace list for errors (including remote station)
• Line information for both fax machine and remote
station
• Machine management list (CSV save), activity report
• Data saved in the storage
1. Check the ECM settings.
2. If the ECM function is disabled on the remote station,
ask the remote station to enable the ECM function.
3. Possibility of line defect (Wrong control of signal
conversion by exchangers)
1. Change the lowest reception sensitivity to -43 dBm.
Change the signal transmission level to -15 dBm.
2. Possibility of line defect (example: packet loss, echo,
distortion, wrong control of signal conversion by exchanger)
1. Turn OFF and ON the main power switch.
2. Dissolve the high load issues.
3. Acquire a log.
• Protocol trace list for errors (including remote station)
• Line information for both fax machine and remote
station
• Machine management list (CSV save), activity report
• Data saved in the storage
1. Make the remote station disable the destination check
function and receive fax normally, then identify the CSI
information from the remote station with the protocol trace
list.
2. Ask the remote station to change the telephone number
(local ID).
3. Make a study on operation when the destination check
setting is disabled.
L-101
L TROUBLESHOOTING > 9. FAX TROUBLE CODE
Installation position
(Service Mode -> [FAX] -> [Line #])
[Function Parameter]: 000E0127(L1),
000E0237(L2), 000E0347(L3),
000E0457(L4) bit1-0: 00 -> 01
-
[Modem/NCU] -> [V17 Send Max
Speed] -> TX Max. Speed
[Function Parameter]: 000E0060
(×1ms)
-
-
Installation position
(Service Mode -> [FAX] -> [Line #])
-
[Communication] -> [Others] -> ECM
Function
-
-
• [Modem/NCU] -> [Level] -> CD/
SED ON Level
• [Modem/NCU] -> [TxATT] -> PIX
TxATT, TONE/Procedure Signal
TxATT, CED/ANSam TxATT
-
-
-
-
-
-
-
Service Manual