Olivetti d-Color MF4003 Service Manual page 496

d-Color MF4003/MF3303
9.9 B17#
Error code Category
B170 MFP soft
error
B171
B173
B176 Memory
allocation
error
B177 Image
processing
error
9.10 B18#
Error code Category
B185 Receiving
data error
B186 Memory
allocation
error
B187 Image
processing
error
B188 MFP soft
error
9.11 B19#
Error code Category
B190 USB I/F error USB sending error
B191
B192
B193
B195
B196
B197
B198
9.12 T0#
Error Catego Contents of error
code ry
T00 Sendin Unable to detect fax
g signal (ANSam/CED/
(Ph.B) DIS) from the remote
station by the time of T1
timeout
Service Manual
Contents of error
Program control error (table control error)
Program control error (instance
acquisition error)
Program control error (interface error)
Unable to secure domain for header (TTI)
image generation
Header (TTI) image generation error
Contents of error
Receiving data size logic error (Receiving
data are not multiples of dotline)
Unable to secure domain for receiving
image
Receiving image conversion error
Program control error (table control error)
Contents of error
USB sending error
Error retry 5 sec. T.O (No response or
other errors)
No response due to detach of USB
Attach not detected for 1 min. after
recovery from sleep when receiving
Detach not detected for 1 min. after shift
from sleep
USB I/F error during formatting when
main power switch ON
Attach not detected for 1 min. after
recovery from sleep at the time other than
receiving
1. Check if the telephone number of the remote station is
used for fax.
2. Turn ON the monitor speaker, and check if the signal
from the remote station can be heard.
3. Change the lowest reception sensitivity to -43 dBm.
Change the signal transmission level to -15 dBm.
4. Extend the DCS retransmission interval.
* If no effect is obtained, return the setting.
5. Extend T1 timer.
Extend the response waiting time. (only for amount of
extended T1 timer)
• Increase by +10 seconds.
* If no effect is obtained, return the setting.
L TROUBLESHOOTING > 9. FAX TROUBLE CODE
• Turn OFF and ON the main power switch.
• Acquire the data saved in the storage from [Service Mode] ->
[Debug Settings] -> [Debug Log Output].
• Use the latest FW.
• Disconnect and then connect the connector of the base board.
• Execute self-diagnosis for all items.
• Try replacing parts. Memory, storage and base board
• Turn OFF and ON the main power switch.
• Acquire the data saved in the storage from [Service Mode] ->
[Debug Settings] -> [Debug Log Output].
• Use the latest FW.
• Disconnect and then connect the connector of the base board.
• Execute self-diagnosis for all items.
• Try replacing parts. Memory, storage and base board
• Turn OFF the main power switch, and turn it ON again after a
check of the USB connection.
• Use the latest FW.
• Acquire the data saved in the storage from [Service Mode] ->
[Debug Settings] -> [Debug Log Output].
• Turn OFF and ON the main power switch.
• Use the latest FW.
• Acquire the data saved in the storage from [Service Mode] ->
[Debug Settings] -> [Debug Log Output].
• Turn OFF the main power switch, and turn it ON again after a
check of the USB connection.
• Use the latest FW.
• Acquire the data saved in the storage from [Service Mode] ->
[Debug Settings] -> [Debug Log Output].
How to correct
L-98
How to correct
How to correct
How to correct
Installation position
(Service Mode -> [FAX] -> [Line #])
-
-
• [Modem/NCU] -> [Level] -> CD/
SED ON Level
• [Modem/NCU] -> [TxATT] -> PIX
TxATT, TONE/Procedure Signal
TxATT, CED/ANSam TxATT
[Function Parameter]: 000E012D(L1),
000E023D(L2), 000E034D(L3),
000E045D(L4) bit1-0: 00 -> 11
• [Communication] -> [TIMER1] ->
T1
• [Network] -> [Network Setting 2] -
> Response Waiting Time
Y119930-3