Olivetti d-Color MF4003 Service Manual page 358

d-Color MF4003/MF3303
Authentication device
USB keyboard emulation card
readers
• *: The card type is reported to the authentication program as an extended card type.
Note *2
▪ Vendor ID and Product ID are identification information to specify USB devices.
▪ Check Vendor ID and Product ID of the USB device to be connected as follows:
▪ Refer to the specification of the device or ask the vendor.
▪ Connect the device to a Windows PC and check "Property" in "Device Manager."
(4) Miscellaneous card readers
• The same setting method as that for AU-201S applies for other card readers.
• The following loadable drivers are necessary.
• Use the loadable driver in advanced combination with the firmware version.
Authentication device
SCL-010
OMNIKEY 5427CK (AU-205H)
KM USB Reader v2 MultiReader HF
KM USB Reader v2 Legic Advant
KM USB Reader v2 ASK FSK 125kHz
KM USB Reader v2 Mot/Ind W26
KM USB Reader v2 HID Prox
KM USB Reader v2 HID iCLASS
Note *1
▪ A combination of the loadable driver and the IC card information setting file will be supplied as a loadable driver by OLI.
Note *2
▪ If cards of HID iClass of OMNIKEY 5427CK (AU-205H) that require detailed settings are to be used, make the detailed settings
by using either one of the following methods:
▪ Using the Auth Device Tool Advanced for 5427CK (AU-205H), prepare a combination of the loadable driver and the IC card
information setting file and export it as a loadable driver.
▪ Using the Auth Device Tool Advanced for 5427CK (AU-205H), prepare the IC card information setting file only and install
the loadable driver in the MFP. Then, using the Data Administrator, write the IC card information setting file in the MFP.
▪ Reference " D.2.1.2 IC card information setting
Note *3
▪ If a YSoft card reader is used, all types of card will be reported as HID Prox card to the authentication program.
▪ To report the card type other than HID Prox to the authentication program, choose the corresponding card type shown in the
following list.
Card Reader Name
KM USB Reader v2
MultiReader HF
KM USB Reader v2 Legic
Advant
KM USB Reader v2 ASK FSK
125kHz
KM USB Reader v2 Mot/Ind
W26
KM USB Reader v2 HID Prox HID Prox
KM USB Reader v2 HID
iCLASS
• *3-1 The content (ID) to be read from the type A card setting differs from which to be read by using AU-201S.
• *3-2 When add the YSoft card reader to the authentication network composed of the present AU-201S, the ID may vary
depending on the card reader. Therefore, it is required to set the card type to TypeA (1), HID Prox (1) or HID iCLASS (1) and
register the card again.
• *3-3 For the content to be read from the HID Prox card, since the ID length is fixed to 16 bytes, the unused part will be bridged
with 0xFF.
• *3-4 If a card type other than HID Prox is selected, the card ID type will be set to up to 512 bytes, the card ID length will be
reported together with the card ID.
• *3-5 If the card type is set to HID Prox by using the LDAP-IC card authentication, specify the card ID type to be sent to the LDAP
server as shown below.
1. Software switch No.135 Hex: 00 Reports that the 1st byte shows the ID length of the card, the 2nd byte and after shows the
card ID. (Default)
2. Software switch No.135 Hex: 01 Reports the card ID with the ID length including the 1st byte.
Note *4
▪ To use FeliCa, make either of the following settings.
▪ Select [FeliCa] at [Administrator] -> [User Auth/Account Track] -> [Authentication Device Settings] -> [Card Authentication]
-> [IC Card type].
Service Manual
J BILLING SETTING/ENHANCED SECURITY/DEBUG SETTINGS > 1. BILLING
Loadable driver name (OLI standard setting)
KeyboardEmu loadable driver
Loadable driver name (OLI standard setting)
SCL-010 loadable driver (Default: TypeA) (*1)(*2)
5427CK (AU-205H) loadable driver (*2)
Loadable driver for YSoft card reader (Default: HID
Prox) (*3)
procedures"
Readable Card Type Card type to be reported to the
authentication program (Default)
Mifare HID Prox
LEGIC HID Prox
EM4100, EM4102, RFID HID Prox
125kHz
Indala HID Prox
HID Prox
HID iCLASS HID Prox
Depends on the card reader *
(*3-3,*3-5)
J-4
Compatible IC cards
Compatible IC cards
TypeA, FeliCa IDm, Mifare
HID Prox, HID iCLASS, TypeA, FeliCa
IDm (*4)
Mifare
LEGIC
EM4100, EM4102, RFID 125kHz
Indala
HID Prox
HID iCLASS
IC Card Information Setting (card type
to be reported) (*3-4)
TypeA (1) (*3-1,*3-2)
TypeA (1) (*3-1,*3-2)
EM4100/
EM4102/
RFID 125kHz
Indala
HID Prox (1) (*3-2)
HID iCLASS (1) (*3-2)
Y119930-3
SETTING