Olivetti d-Color MF4003 Service Manual page 503

d-Color MF4003/MF3303
Error Catego Contents of error
code ry
T89 Sendin When the control unit is
g connected, a capacity
(control shortage occurs during
unit) communication
(To be determined
before start of
communication when
using a coin vendor)
9.21 T9#
Error Catego Contents of error
code ry
T90 Sendin Data may have been
g (line transmitted with no line
selectio specified when "No" is
n) selected for TX-Line
Auto Switch Setting.
T91 Data may have been
transmitted with an
illegal line specified.
T95 Recepti Detected short
on disconnection (line
disconnection) during
reception
9.22 R0#
Error Catego Contents of error
code ry
R00 Recepti Unable to detect fax
on signal (CNG/DCS) from
(Ph.B) the remote station by the
time of T1 timeout
R01 Mixed Unable to detect the
size DCS (reception ability
recepti signal) from the remote
on station by T1 timeout
(Ph.B') after received the
change instructions
(PPS-EOM) of original
size or resolution
Y119930-3
How to correct
Details can be checked with the record which is made by
the monitor speaker or telephone line.
2. Possibility of line defect
Check the remaining capacity of the control unit.
How to correct
Specify the line to be used to send.
Change the line specification of the abbreviated
registration.
(Since the abbreviated registration has been imported with
an uninstalled line specified, the abbreviated registration
must be modified.)
Check for any telephone line connection error.
A breakage on underfloor wiring may be a possible cause.
How to correct
1. Set the Receive Signal Detection Mode to No. of Times. [Network] -> [Network Setting 1] ->
2. Set the 1300Hz Detection setting to OFF if possible.
(Fax destination: Japan only)
3. For 1300Hz Detection (JP), connect the ground for the
MFP/TA/PBX. (Fax destination: Japan only)
4. Change the setting of 1300Hz detection frequency. (Fax
destination: Japan only)
5. Turn ON the monitor speaker, and check if the fax signal
from the remote station can be heard. If cannot, it is judged
as a wrong number.
6. Change the lowest reception sensitivity to -43 dBm.
Change the signal transmission level to -15 dBm.
7. Extend T1 timer.
Extend the response waiting time. (only for amount of
extended T1 timer)
• Increase by +10 seconds.
* If no effect is obtained, return the setting.
8. Extend the DIS retransmission interval.
1. Change the lowest reception sensitivity to -43 dBm.
Change the signal transmission level to -15 dBm.
2. Extend T1 timer.
Extend the response waiting time. (only for amount of
extended T1 timer)
• Increase by +10 seconds.
* If no effect is obtained, return the setting.
L-105
L TROUBLESHOOTING > 9. FAX TROUBLE CODE
Installation position
(Service Mode -> [FAX] -> [Line #])
-
-
Installation position
(Service Mode -> [FAX] -> [Line #])
-
-
-
Installation position
(Service Mode -> [FAX] -> [Line #])
Receive Signal Detection Mode
[Network] -> [Network Setting 2] ->
1300Hz Detection
-
[Function Parameter]: 000E0051
bit1-0: 00 -> 01
-
• [Modem/NCU] -> [Level] -> CD/
SED ON Level
• [Modem/NCU] -> [TxATT] -> PIX
TxATT, TONE/Procedure Signal
TxATT, CED/ANSam TxATT
• [Communication] -> [TIMER1] ->
T1
• [Network] -> [Network Setting 2] -
> Response Waiting Time
[Function Parameter]: 000E0053 -> 4.5
sec (0x2D=00101101)
• [Modem/NCU] -> [Level] -> CD/
SED ON Level
• [Modem/NCU] -> [TxATT] -> PIX
TxATT, TONE/Procedure Signal
TxATT, CED/ANSam TxATT
[Communication] -> [TIMER1] -> T1
Service Manual