Olivetti d-Color MF4003 Service Manual page 507

d-Color MF4003/MF3303
9.25 R3#
Error Catego Contents of error
code ry
R33 Polling DIS is received after
TX switching to Polling TX.
(Ph.B)
R34 F code When performing F-code
recepti (confidential/relay)
on communication, the
(Ph.B) password information as
well as the box number
(SUB) are received with
PWD but not SID.
R37 Recepti V.34 communication
on disabled due to line
noise
Example: The machine
is disconnected first.
R38 V.34 communication
disabled due to line
noise
9.26 R4#
Error Catego Contents of error
code ry
R40 Recepti Fax soft error
on
R45 NonEC Timeout due to
M interruption while
recepti receiving image data
on
(Ph.C)
R49 Recepti DCN is received after
on CFR has been sent
back.
Example: The remote
station is disconnected
due to T1 timeout.
9.27 R5#
Error Catego Contents of error
code ry
R50 NonEC Amount of error lines in
M image data exceeded
recepti specific value when
on decoding image data
(detected from fax
board)
R51 Recepti Fax soft error
on
Y119930-3
How to correct
Turn OFF the DTS function.
Request the machine on sending end to set the password
information to SID but not PWD.
NOTE) PWD is used for SEP polling.
1. Turn OFF V.34.
2. Check if an error has occurred on the machine on other
end of line first.
Turn OFF V.34.
How to correct
1. Dissolve the high load issues.
2. It cannot be dissolved by settings, so acquire a log.
(since an error may occur on the DIS received from the
remote station or altered by exchangers in midway)
• Protocol trace list for errors (including remote station)
• Line information for both fax machine and remote
station
• Machine management list (CSV save), activity report
• Data saved in the storage
1. Check the fax machine for that if a job is canceled or a
communication error occurred.
2. Enable communication with ECM.
If ECM has been already set to ON on your machine,
request the sending end to do it.
3. Set 000E000D bit7 to 0 to turn OFF the timer.
4. Possibility of line defect (due to wrong control of signal
conversion by exchanger)
1. Change the lowest reception sensitivity to -43 dBm.
Change the signal transmission level to -15 dBm.
2. Possibility of line defect (example: packet loss, echo,
distortion)
How to correct
1. Enable communication with ECM.
If ECM has been already set to ON on your machine,
request the sending end to do it.
2. Possibility of line defect (example: packet loss,
distortion)
1. Turn OFF and ON the main power switch.
2. Set the coding method to MH/MR/MMR.
3. If the error reoccurs on the specific remote station, it
cannot be dissolved by settings, so acquire a log.
• Protocol trace list for errors (including remote station)
• Line information for both fax machine and remote
station
• Machine management list (CSV save), activity report
• Data saved in the storage
L-109
L TROUBLESHOOTING > 9. FAX TROUBLE CODE
Installation position
(Service Mode -> [FAX] -> [Line #])
[Function Parameter]: 000E0052 bit0:
1 -> 0
-
[Communication] -> [Protocol] -> V8/
V34 Protocol
-
[Communication] -> [Protocol] -> V8/
V34 Protocol
Installation position
(Service Mode -> [FAX] -> [Line #])
-
-
-
[Communication] -> [Others] -> ECM
Function
-
-
• [Modem/NCU] -> [Level] -> CD/
SED ON Level
• [Modem/NCU] -> [TxATT] -> PIX
TxATT, TONE/Procedure Signal
TxATT, CED/ANSam TxATT
-
Installation position
(Service Mode -> [FAX] -> [Line #])
[Communication] -> [Others] -> ECM
Function
-
-
[Communication] -> [Others] -> Coding
Ability
-
Service Manual