Olivetti d-Color MF4003 Service Manual page 357

d-Color MF4003/MF3303
1.4.1 Installation procedures of authentication unit
(1) AU-102
1. Install the AU-102 loadable driver (BIO_LDR.tar) to the main unit. (*1)
2. Install the AU-102 to the main unit.
3. Select [Body] in [Service Mode] -> [Billing Settings] -> [Authentication Device 2].
4. Turn off the main power switch and turn it on again more than 10 seconds after.
5. Register the authentication user data.
Note *1
▪ Use the loadable driver in advanced combination with the firmware version.
Authentication device
AU-102
(2) AU-201S
1. Install the loadable driver (ICC_LDR.tar) to the main unit. (*1)(*2)(*3)
2. Install the AU-201S to the main unit.
3. Select [Card] in [Service Mode] -> [Billing Settings] -> [Authentication Device 2].
4. Turn off the main power switch and turn it on again more than 10 seconds after.
5. Register the authentication card data.
Note *1
▪ A combination of the loadable driver and the IC card information setting file will be supplied as a loadable driver by OLI.
Note *2
▪ The loadable driver to be installed varied according to the type of the card. Identify the type of the card requiring authentication
and install the correct loadable driver.
▪ Use the loadable driver in advanced combination with the firmware version.
Authentication device
AU-201S
Note *3
▪ If FeliCa IDm, FeliCa SSFC, FeliCa Private, or related card requiring detailed settings is to be used, make the detailed settings
by using either one of the following methods:
1. Using the Auth Device Tool Advanced for AU-201S, prepare a combination of the loadable driver and the IC card information
setting file and export it as a loadable driver.
IC card information setting file preparation tool
2. Using the Auth Device Tool Advanced for AU-201S, prepare the IC card information setting file only and install the loadable
driver in the MFP. Then, using the Data Administrator, write the IC card information setting file in the MFP.
IC card information setting procedures
E.g.: Information setting sample when the FeliCa SSFC card is used
Items of FeliCa SSFC detail setting
Room number
Floor number
Building number
Area number
Security level
Company identification code (CL code)
(*1)
Company code (*2)
*1: The character length of the company code is 10 bytes.
*2: Use alphabetical upper case/lower case characters and numeric characters for Company code. When the company code is not set, this
space will be left blank.
(3) USB keyboard emulation card readers
1. Install the loadable driver (ICC_LDR.tar) to the main unit. 1
2. Select [Card] in [Service Mode] -> [Billing Settings] -> [Authentication Device 2].
3. Turn OFF the main power switch, wait for 10 sec., then turn the switch ON.
4. Set Vendor ID and Product ID of the card reader in [Administrator] -> [User Auth/Account Track] -> [Authentication Device Settings] ->
[Card Authentication] -> [USB Device identification information]. 2
5. Turn OFF the main power switch.
6. Install the USB keyboard emulation card readers to the main unit.
7. Turn ON the main power switch.
8. Register the authentication card data.
NOTE
▪ Use the card reader supporting US keyboards.
▪ The length of card ID is 1 to 512 bytes.
▪ Send data as card ID data received until the reception of the key code that has been set as a delimiter (Enter).
Note *1
▪ Use the loadable driver in advanced combination with the firmware version.
Y119930-3
Body
Loadable driver name (OLI standard setting)
AU-201S loadable driver
Information to be obtained from the administrator
Sample-data (decimal number)
06BGLQVX17 (ASCII code)
CompanyA (ASCII code)
J BILLING SETTING/ENHANCED SECURITY/DEBUG SETTINGS > 1. BILLING
Compatible IC cards
FeliCa IDm, FeliCa SSFC, FeliCa FCF, FeliCa
FCF(Campus), TypeA FeliCaPrivate
37
15
50
85
2
J-3
Compatible IC cards
Setting value (hexadecimal number)
00 25
00 0F
00 32
00 55
00 02
30 36 42 47 4C 51 56 58 31 37
CompanyA
Service Manual
SETTING