Olivetti d-Color MF4003 Service Manual page 193

d-Color MF4003/MF3303
Key name
Destination Check Display
Function
Number Display Function
(Only for Japan)
Confirm Address (TX)
Confirm Address (Register)
PIN Code Display Mask
Function
Reset the setting value after
using other functions
Require the use of the use of
the External Line key for
outside calling
Prohibit fax usage while
using ext TEL line
Dial-In Settings (Only for It will be displayed when [Service Mode] -> [FAX] -> [System] -> [Display Setting] -> [Dial In] is set to "ON."
Japan)
Closed Network RX It will be displayed when [Service Mode] -> [FAX] -> [System] -> [Display Setting] -> [Closed area RX] is set to
"ON."
Remote RX Settings (Only It will be displayed when [Service Mode] -> [FAX] -> [System] -> [Display Setting] -> [Remote Rx] is set to "ON."
for Japan)
Incomplete TX Hold
RX Data Operation Memory RX Setting
Settings
Forward TX Setting
PC-Fax RX Setting
TSI User Box Settings
None
PC-Fax TX Setting -
RX Data Deletion Password Deletion
Restriction Settings
Administrator User Box
Deletion
PBX Connection Setting -
6.10.5 Report Settings
Key name
TX Result Report
Tx Result Report Print
Confirmation Screen
Sequential TX Report
Broadcast Result Report
Bulletin TX Report
Relay TX Result Report
TX Result Report Print Settings
Activity Report
Relay Request Report
PC-Fax TX Error Report
Y119930-3
-
It will be displayed when [Service Mode] -> [FAX] -> [System] -> [Display Setting] ->
[Number display] is set to "ON."
-
-
-
-
-
-
• It will be displayed when [Service Mode] -> [FAX] -> [System] -> [Display Setting] -> [Re-Transmission] is set
to "ON."
• It will not be displayed when [Service Mode] -> [Billing Setting] -> [Management Function Choice] shows that
"Key Counter Only" or "Vendor 2" is mounted.
It will be displayed when [Service Mode] -> [FAX] -> [System] -> [Display Setting] ->
[Compulsory Memory RX] is set to "ON."
[Dail-In only] will be displayed when [Administrator] -> [Fax Settings] -> [Function
Setting] -> [Dial-In Settings] is set to "ON."
-
-
-
-
-
-
-
It will be displayed when [Service Mode] -> [FAX] -> [System] -> [Display Setting] -> [Relay] is set to "ON."
Print • This function can be set if "E-mail address" has been set in [Administrator] ->
E-mail Notification
• This function can be set if "ON" is set for [E-mail TX (SMTP)] and "ON" is set for
It will not be displayed when [Service Mode] -> [Billing Setting] -> [Management Function Choice] shows
that the "Vendor 2" is mounted.
It will be displayed when [Service Mode] -> [FAX] -> [System] -> [Display Setting] -> [Relay] is set to "ON."
-
Function/Precondition
• It will not be displayed when [Service Mode] -> [Billing Setting] ->
[Management Function Choice] shows that the "Vendor 2" is mounted.
• It will not be displayed when [Service Mode] -> [Billing Setting] shows that
[Authentication Device2] is mounted.
• A forwarding address except a case of the fax, specify [File Type] a fax can be
converted into a file. The file types able to be specified are PDF, XPS, and
TIFF. However, when a received job is an Internet Fax or IP Address Fax, you
can specify other file types by changing the switch No.124 to [00000001] at Bit
assignment/[01] at HEX assignment in [Service Mode] -> [System 2] ->
[Software Switch Setting].
• This setting is not available without user authentication.
• This setting is not available without the account track.
• This function cannot be set if the User Box Administrator has not been set.
Function/Precondition
[System Settings] -> [Machine Setting].
[E-Mail Send] in [Administrator] -> [Network] -> [E-mail Setting].
H-25
H UTILITY MODE > 6. Administrator
Service Manual