Lightware UMX-TPS-TX120 User Manual page 145


  
7. LW3 Programmers' Reference
RS-232 Message Sending
Sending a Message (ASCII-format) via RS-232
ç CALL·/MEDIA/UART/P1:sendMessage(<message>)
Sending a Text (ASCII-format) via RS-232
ç CALL·/MEDIA/UART/P1:sendText(<message>)
Sending a Binary Message (HEX-format) via RS-232
ç CALL·/MEDIA/UART/P1:sendBinaryMessage(<message>)
Using Hexadecimal Codes
RS-232 Message Recognizer
Enable the Recognizer
SET·/MEDIA/UART/<serial_port>.RecognizerEnable=<recognizer_enable>
ç
Set the Delimiter Hex
SET·/MEDIA/UART/RECOGNIZER.DelimiterHex=<delimiter>
ç
Set the Timeout
SET·/MEDIA/UART/RECOGNIZER.TimeOut=<timeout>
ç
Querying the Last Recognized Message (String)
ç GET·/MEDIA/UART/RECOGNIZER.Rx
Querying the Last Recognized Message(Hex)
ç GET·/MEDIA/UART/RECOGNIZER.RxHex
Clearing the Last Recognized Stored Message
ç CALL·/MEDIA/UART/RECOGNIZER:clear()
Querying the Last Recognized Active Message (String)
ç GET·/MEDIA/UART/RECOGNIZER.ActiveRx
Querying the Last Recognized Active Message (Hex)
ç GET·/MEDIA/UART/RECOGNIZER.ActiveRxHex
Set the Active Timeout
SET·/MEDIA/UART/RECOGNIZER.ActivePropertyTimeout=<a_timeout>
ç
Running an Immediate Event Action
SET·/CTRL/TCP/C<loc>.ActionTrigger=<event_nr>
ç
Sending CEC Commands
Press&Release Commands
ç CALL·/MEDIA/CEC/<port>:sendClick(<command>)
Applied firmware packages: (UMX-TPS): v1.5.0b4 | (WP-UMX-TPS): v1.4.0b8 | (FP-UMX-TPS): v1.4.0b8 | LDC software: v2.5.6b2
UMX-TPS-TX100 series – User's Manual
Further Commands
ç CALL·/MEDIA/CEC/<port>:send(<command>)
Sending an OSD String
SET·/MEDIA/CEC/<port>.OsdString=<text>
ç
ç CALL·/MEDIA/CEC/<port>:send(set_osd)
Sending CEC Commands in Hex Format
ç CALL·/MEDIA/CEC/<port>:sendHex(<hex_code>)
Querying the Last Received CEC Message
ç GET /MEDIA/CEC/<port>.LastReceivedMessage
Infrared Port Configuration
Enable Command Injection Mode
ç SET·/MEDIA/IR/<port>.CommandInjectionEnable=true|false
Enable/Disable Output Signal Modulation
ç SET·/MEDIA/IR/<port>.EnableModulation=true|false
Infrared Message Sending
Sending Pronto Hex Codes in Little-endian Format via IR Port
ç CALL·/MEDIA/IR/<output_port>:sendProntoHex(<hex_code>)
Sending Pronto Hex Codes in Big-endian Format via IR Port
ç CALL·/MEDIA/IR/<output_port>:sendProntoHexBigEndian(<hex_code>)
GPIO Port Configuration
Set the Direction of a GPIO Pin
SET·/MEDIA/GPIO/<port>.Direction=<direction>
ç
Set the Output Level of a GPIO Pin
SET·/MEDIA/GPIO/<port>.Output=<value>
ç
Toggle the Level of a GPIO Pin
ç CALL·/MEDIA/GPIO/<port>:toggle()
EDID Management
Query the Emulated EDIDs
ç GET·/EDID.EdidStatus
Query the Validity of a Dynamic EDID
ç GET·/EDID/D/<dynamic>.Validity
145