Lightware UMX-TPS-TX120 User Manual page 144


  
7. LW3 Programmers' Reference
Sending a TCP Text (ASCII-format)
ç CALL·/MEDIA/ETHERNET:tcpText(<IP_address>:<port_no>=<text>)
Sending a TCP Binary Message (HEX-format)
ç CALL·/MEDIA/ETHERNET.tcpBinary(<IP_address>:<port_no>=<HEX_message>)
Sending a UDP Message (ASCII-format)
ç CALL·/MEDIA/ETHERNET:udpMessage(<IP_address>:<port_no>=<message>)
Sending a UDP Text (ASCII-format)
ç CALL·/MEDIA/ETHERNET:udpText(<IP_address>:<port_no>=<text>)
Sending a UDP Binary Message (HEX-format)
ç CALL·/MEDIA/ETHERNET:udpBinary(<IP_address>:<port_no>=<HEX_message>)
HTTP Messaging
Setting the Target IP Address
SET·/CTRL/HTTP/C1.ServerIP=<IP_address>
ç
Setting the TCP Port
SET·/CTRL/HTTP/C1.ServerPort=<port_no>
ç
Setting the Target Path
SET·/CTRL/HTTP/C1.File=<path>
ç
Setting the Message Header
SET·/CTRL/HTTP/C1.Header=<header_text>
ç
Sending a Post Message
ç CALL·/CTRL/HTTP/C1:post(<body_text>)
Sending a Put Message
ç CALL·/CTRL/HTTP/C1:put(<body_text>)
TCP Message Recognizer
Setting the IP Address of the TCP Server
SET·/CTRL/TCP/C<loc>.ServerIP=<IP_address>
ç
Setting the TCP/IP Port Number of the TCP Server
SET·/CTRL/TCP/C<loc>.ServerPort=<port_no>
ç
Connecting to a TCP Server
ç CALL·/CTRL/TCP/C<loc>:connect()
Disconnecting from a TCP Server
ç CALL·/CTRL/TCP/C<loc>:disconnect()
Applied firmware packages: (UMX-TPS): v1.5.0b4 | (WP-UMX-TPS): v1.4.0b8 | (FP-UMX-TPS): v1.4.0b8 | LDC software: v2.5.6b2
UMX-TPS-TX100 series – User's Manual
Setting the Delimiter Hex
SET·/CTRL/TCP/C<loc>.DelimiterHex=<delimiter>
ç
Setting the Timeout
SET·/CTRL/TCP/C<loc>.TimeOut=<timeout>
ç
Querying the Last Recognized Message (String)
ç GET·/CTRL/TCP/C<loc>.Rx
Querying the Last Recognized Message (Hex)
ç GET·/CTRL/TCP/C<loc>.RxHex
Clearing the Last Recognized Stored Message
ç CALL·/CTRL/TCP/C<loc>:clear()
Querying the Last Recognized Active Message (String)
ç GET·/CTRL/TCP/C<loc>.ActiveRx
Querying the Last Recognized Active Message (Hex)
ç GET·/CTRL/TCP/C<loc>.ActiveRxHex
Set the Active Timeout
SET·/CTRL/TCP/C<loc>.ActivePropertyTimeout=<a_timeout>
ç
Running an Immediate Event Action
SET·/CTRL/TCP/C<loc>.ActionTrigger=<event_nr>
ç
RS-232 Port Configuration
Protocol Setting
SET·/MEDIA/UART/<port>.ControlProtocol=<protocol>
ç
BAUD Rate Setting
SET·/MEDIA/UART/<port>.Baudrate=<baudrate>
ç
Databits Setting
SET·/MEDIA/UART/<port>.DataBits=<databits>
ç
Stopbits Setting
SET·/MEDIA/UART/<port>.StopBits=<stopbits>
ç
Parity Setting
ç SET·/MEDIA/UART/
RS-232 Operation Mode
SET·/MEDIA/UART/<port>.Rs232Mode=<mode>
ç
Command Injection Enable
SET·/MEDIA/UART/<port>.CommandInjectionEnable=<logical_value>
ç
<port>.Parity=<parity>
144