Lightware UMX-TPS-TX120 User Manual page 180


  
11. Appendix
v1.1.5b1
Release date: 2018-03-01
New feature:
▪ New miniweb.
v1.1.3b1
Release date: 2017-10-18
Bugfix:
▪ Fixed GPIO PortUiCode.
v1.1.2b4
Release date: 2017-10-16
New feature:
▪ The text names of the ports are changed to be more precise, and less ambiguous.
▪ With too many devices connected, one can find it hard to pair the physically connected devices with
the listed devices in LDC device discovery window. That is why Lightware is introducing the new
IdentifyMe feature, which identifies the desired device by blinking its LEDs for a period of time. That
helps the user visually recognize the requested device.
▪ Now Bonjour shows firmware version as well.
Bugfix:
▪ Fixed a bug that made the 'continuously exists' timing mode unable to use.
▪ Fixed a bug that caused Event Manager's 47th event to be unlink-able.
v1.1.1b1
Release date: 2016-05-11
New feature:
▪ Autoselection connect and disconnect delay can be configured via LW3 methods.
Bugfix:
▪ Unsupported dual link DVI EDIDs removed from factory EDID list.
▪ Event manager conditions did not work if DP input properties were selected.
▪ Input background measurement speed improved.
▪ If the user switched to the currently selected port, the output was disconnected and connected again
unnecessarily, which resulted in a picture drop. Fixed.
▪ /SYS/MB/UMXDP node renamed to /SYS/MB/DP
Applied firmware packages: (UMX-TPS): v1.5.0b4 | (WP-UMX-TPS): v1.4.0b8 | (FP-UMX-TPS): v1.4.0b8 | LDC software: v2.5.6b2
UMX-TPS-TX100 series – User's Manual
v1.1.0b1
Release date: 2016-04-11
New feature:
▪ New EDID driver is used, the content of some factory EDID's are changed according to EDID 1.3 and
1.4 standard.
▪ EDID node properties changed: PreferredResolution, MonitorName and AudioInfo properties are added
▪ Audio and video port names are changed: 'I' is used for inputs and 'O' is used for outputs, instead of 'P'.
▪ Crosspoint properties and methods changed. Warning: If you are using an external controller for this
device via LW3 protocol, the recent changes in property and node names may result in difficulties to
control the TPS device with the latest firmware.
▪ TCP and UDP messages can be sent by the device to control projectors and any other devices. This
feature can also be used with Event Manager.
▪ IR command injection is now supported: data received on a specific TCP port is transmitted as IR
signal, and the received IR frames are also sent to this TCP connection.
▪ The device is able to identify IR commands on either the local or link IR input port. This feature can be
connected to Event Manager, which means, that the device can be programmed to do various actions,
if a specific IR command is detected.
▪ Factory default can be given in the board component.
▪ New bootloader is used, which allows the connected TPS-RX95's to be updated remotely.
▪ Event Manager updated: time delay can be configured between condition and action, a condition can
trigger multiple actions at the same time, inverse condition can be used.
▪ Dynamic edid can be deleted from code.
▪ 3840x2160p60 YUV4:2:0 factory EDID added.
▪ Event Manager configuration became more user friendly: actions can be triggered manually for testing
and the user interface shows if any of the conditions are met.
▪ FRAMEWORK update.BUGFIX: Minor bug fix in default emulated edids.
▪ The method of storing device settings in EEPROM is updated, which may result in losing all the
settings, logs and user EDID's after updating to 1.1.0. The LDU software contains a plug-in to help you
keep the actual settings after firmware update.
▪ Default emulated edid for UmxAvFrontend handling changed.
Bugfix:
▪ Error log is accessible at /MANAGEMENT/LOG/RAMLOG node.
▪ If no sync screen is active, the output resolution is now reported correctly by the output port.
▪ Compatibility issues with Gefen HDMI 1.3 HdBaseT extender fixed.
▪ Reporting the resolution of signals in YUV 4:2:0 colorspace fixed.
▪ In case of sending DVI signal on the output, the audio output port does not indicate signal present.
180