Network Configuration; Query The Current Ip Status; Set The Ip Address; Set The Subnet Mask - Lightware UMX-TPS-TX120 User Manual


  
6. LW2 Programmer's Reference
6.5. Network Configuration
6.5.1. Query the Current IP Status
The IP address settings can be queried as follows.
Command and Response
ȩ {IP_STAT=?}
Ȩ (IP_STAT=<type>;<ip_address>;<subnet_mask>;<gateway_addr>)CrLf
Parameters
Parameter Parameter description
<type> Assignment of the IP address
<ip_addr> IP address
<subnet_mask> Subnet mask
<gateway_addr> Gateway address
Example
ȩ {ip_stat=?}
Ȩ (IP_STAT=0;192.168.0.100;255.255.255.0;192.168.0.1)
The device has a static (fix) IP address: 192.168.0.100; the subnet mask is 255.255.255.0, the gateway
address is 192.168.0.1.
6.5.2. Set the IP Address
IP address can be set as follows.
Command and Response
ȩ {IP_ADDRESS=<type>;<ip_address>}
Ȩ (IP_ADDRESS=<type>;<ip_address>)CrLf
Parameters
See the previous section.
Example
ȩ {ip_address=0;192.168.0.110}
Ȩ (IP_ADDRESS=0;192.168.0.110)

INFO: The IP address can be queried by typing the {ip_address=?} command. The response contains the
fix IP address that is stored in the device even if DHCP is enabled; in this case, this IP address is not valid.
#dhcp #ipaddress #network
Value Value description
static
0
dynamic (DHCP)
1
(four decimal octets separated by dots)
(four decimal octets separated by dots)
(four decimal octets separated by dots)
Applied firmware packages: (UMX-TPS): v1.5.0b4 | (WP-UMX-TPS): v1.4.0b8 | (FP-UMX-TPS): v1.4.0b8 | LDC software: v2.5.6b2
UMX-TPS-TX100 series – User's Manual
6.5.3. Set the Subnet Mask
Subnet mask can be set as follows.
Command and Response
ȩ {IP_NETMASK=<subnet_mask>}
Ȩ (IP_NETMASK=<subnet_mask>)CrLf
Parameters
See the

Query the Current IP Status

Example
ȩ {ip_netmask=255.255.255.0}
Ȩ (IP_NETMASK=255.255.255.0)

INFO: The subnet mask can be queried by typing the {ip_address=?} command. The response contains
the fix IP subnet mask that is stored in the device even if DHCP is enabled; in this case, this IP subnet
mask is not valid.
6.5.4. Set the Gateway Address
Gateway address can be set as follows.
Command and Response
ȩ {IP_GATEWAY=<gateway_addr>}
Ȩ (IP_GATEWAY=<gateway_addr>)CrLf
Parameters
See the Query the Current IP Status
Example
ȩ {ip_gateway=192.168.0.50}
Ȩ (IP_GATEWAY=192.168.0.50)

INFO: The gateway address can be queried by typing the {ip_gateway=?} command. The response contains
the static IP gateway address that is stored in the device even if DHCP is enabled. In that case, the latest
valid gateway address (for static IP) is stored.
6.5.5. Apply Network Settings
Apply the network settings and restart the network interface.
Command and Response
ȩ {ip_apply}
Ȩ (IP_APPLY)CrLf
Example
ȩ {ip_apply}
Ȩ (IP_APPLY)
section.
section.
93