Lightware UMX-TPS-TX120 User Manual page 179


  
11. Appendix
▪ LWROS integration compatible for LDU2 only!
▪ Added 'Dark mode' function to turn off front panel LEDs
▪ Modified DP input driver to fix HDCP issue with MacBooks
▪ RS232 Minimal Recognizer for Cisco compatibility (Cisco Login) for WP-UMX-TPS-TX130-Plus only!
▪ Improved GPIO detection
▪ Use LDU2 v1.2.5 or later for the update!
▪ Added 'User replaceable miniweb slot' to support built-in control webpage
▪ Added 'Forced button lock' function to lock buttons via protocol command
Bugfix:
▪ Poe enable state is now reloaded after reboot.
▪ Input video parameter measurement speed improved.
▪ Unsupported dual link DVI EDIDs removed from factory EDID list.
▪ /SYS/MB/UMXDP node renamed to /SYS/MB/DP
▪ Event manager conditions did not work if DP input properties were selected.
▪ If the user switched to the currently selected port, the output was disconnected and connected again
unnecessarily, which resulted in a picture drop. Fixed.
▪ Compatibility issues with Gefen HDMI 1.3 HdBaseT extender fixed.
▪ In case of sending DVI signal on the output, the audio output port does not indicate signal present.
▪ If the output was set to HDCP Always mode, the signal was sent out unencrypted, if the input port was
disconnected and connected again. This issue only happened, if the input signal was also unencrypted.
▪ If no sync screen is active, the output resolution is now reported correctly by the output port.
▪ Reporting the resolution of signals in YUV 4:2:0 colorspace fixed.
▪ In case of sending 1920x1200 no sync screen, the device did not notice the connection state changes
on the inputs. Fixed.
v1.3.2b1
Release date: 2019-05-21
Bugfix:
▪ Use LDU2 v1.2.5 or later for the update!
v1.3.1b1
Release date: 2019-04-17
Bugfix:
▪ bugfix to support for previous HW versions
Applied firmware packages: (UMX-TPS): v1.5.0b4 | (WP-UMX-TPS): v1.4.0b8 | (FP-UMX-TPS): v1.4.0b8 | LDC software: v2.5.6b2
UMX-TPS-TX100 series – User's Manual
v1.3.0b11
Release date: 2019-04-17
New feature:
▪ RS232 Minimal Recognizer for Cisco compatibility (Cisco Login) for UMX-TPS-TX140-Plus only!
▪ Sending IR codes (SendProntoHex e.g. send max. 200 Byte IR code with Event Actions) for UMX-TPS-
TX140-Plus only!
▪ Use LDU2 v1.2.3 or later for the update!
▪ CEC - sendCEC command (e.g. turn on the TV with Event Actions) for UMX-TPS-TX140-Plus only!
Bugfix:
▪ Fixed Event Manager condition linking
v1.2.1b8
Release date: 2019-01-29
New feature:
▪ Firmware platform library updated
▪ Modified DP input driver to fix HDCP issue with MacBooks
▪ Compatible for LDU2 only!
▪ Modified RS-232 modes to support SendMessage in Control mode
▪ Added 'Disable default button function' option to support button customization in Event Manager
▪ Added 'Forced button lock' function to lock buttons via protocol command
▪ Added 'Dark mode' function to turn off front panel LEDs
▪ Video crosspoint driver improvements
▪ AV input driver improvements
▪ Improved GPIO detection speed (quick impulses can be detected, even low as 80ms)
v1.1.7b2
Release date: 2018-05-18
Bugfix:
▪ Rs232 even parity parameter bug fixed.
v1.1.6b1
Release date: 2018-04-10
New feature:
▪ New control.html.
179