Error Codes (Send); Self-Diagnostic Display - Canon Color iR C3480 Service Manual

Chapter 16

16.3 Error Codes (SEND)

16.3.1 Self-Diagnostic Display

Color iR C3380G / Color iR C2880G / Color iR C3380i / Color iR C3380 / Color iR C2880i / Color iR C2880 / iR C3480 / iR C3480i / iR C3080 / iR C3080i / iR
C2550
Cause
Scanning has stopped because the size of the data for the scanned original exceeds the limit. Scanning may be possible if [Data Cmprssn] is set to [High
Ratio], Resolution is lowered, or [Sharpness] is reduced.
Scanning was stopped because the data size of the scanned original exceeded the
maximum data size that the machine could handle.
Out of resources. Wait for a moment, then perform operation again.
You cannot browse the network. There is a lack of TCP/IP resources because
documents have just been continuously sent or are being continuously sent
through FTP or Windows (SMB).
Set the IP Address.
This machine is not set with an IP address.
No response from the server. Check the settings.
The specified server settings are incorrect, or the server is not turned ON.
Alternatively, the machine's TCP/IP resources may be low.
NetWare is in use. Wait for a moment, then perform operation again.
You cannot browse the network because NetWare is printing through a Pserver or
NDS PServer.
There are too many subdirectories.
You have exceeded the maximum number of subdirectory levels allowed.
No response.
The server was not running when you tried to send.
The network connection was lost when you tried to send. (Either you could not
connect to the destination, or the connection was lost before the job could be
completed.)
You tried to send through NetWare, but the Tree name was not entered.
A TCP/IP error occurred when you tried to send an e-mail message or an I-fax.
Check the TCP/IP.
Cause The machine's TCP/IP connection is not operating.
Cannot find the selected server. Check the settings.
The IP address that the machine should connect to cannot be determined.
If Login Information in Register LDAP Server in System Settings (from the
Additional Functions screen) is set to 'Use (security auth.)' for the LDAP server,
the machine will not be able to determine the host name.
Cannot connect to the selected server. Check the settings.
The machine cannot connect to the specified IP address/port.
Check the user name and password or check settings.
When setting Login Information for the LDAP server to 'Use' or 'Use (security
auth.)', the user name or password is incorrect.
When setting Login Information for the LDAP server to 'Use (security auth.)', the
domain name is incorrect.
Cannot complete searching due to timeout. Check the settings.
The search could not be completed within the time specified under <Search
Timeout>.
The number of search results has exceeded limits. Change search conditions and try again.
16-18
T-16-7
Remedy
By selecting [High Ratio] for Data Compression Ratio, lowering the Resolution,
and lowering the Sharpness setting, scanning may become possible.
Wait for a while, and try browsing again.
Specify the IP Address Settings in TCP/IP Settings in Network Settings in System
Settings (from the Additional Functions screen), then turn the machine's main
power OFF and back ON again.
Wait for a while, and try browsing again. If there is still no response from the
server, try selecting another server.
Wait until printing is complete, then try browsing again.
Specify a different destination because the directory level that you are trying to
access cannot be specified.
Make sure that the server is ON, and check the destination.
Check the status of the network.
Enter the Tree name.
Check that the network cables and connectors are properly connected.
Check the IP Address Settings (IP Address, DHCP, RARP, BOOTP) in TCP/IP
Settings in Network Settings in System Settings (from the Additional Functions
screen).
1. Check the DNS Server Settings in TCP/IP Settings in Network Settings in
System Settings (from the Additional Functions screen).
2. Check whether the DNS server's DNS settings are correct.
Check the DNS Server Settings in TCP/IP Settings in Network Settings in System
Settings (from the Additional Functions screen).
1. Check the Gateway Address setting in IP Address Settings in TCP/IP Settings
in Network Settings in System Settings (from the Additional Functions screen).
2. Check the Server Address and Port Number in Register LDAP Server in System
Settings (from the Additional Functions screen).
3. Check whether the LDAP server is operating normally.
4. If Login Information in Register LDAP Server in System Settings (from the
Additional Functions screen) is set to 'Use (security auth.)' for the LDAP server,
check whether UDP (User Datagram Protocol) packages are blocked by the filter.
Check the User and Password settings when Login Information in Register LDAP
Server in System Settings (from the Additional Functions screen) is set to 'Use' or
'Use (security auth.)'.
Check the Domain Name setting when Login Information in Register LDAP
Server in System Settings (from the Additional Functions screen) is set to 'Use
(security auth.)'.
Increase the time setting for Search Timeout in Register LDAP Server in System
Settings (from the Additional Functions screen).
0014-6629