Advertisement
16.4 Alarm Code
16.4.1 Alarm Code (ADF)
Code
Name
0003H Separation NG alarm
16.5 Fax Error Codes
16.5.1 Outline
16.5.1.1 Error Code Outline
An error code is used to indicate a fault in a machine, and is indicated in the machine's LCD or reports, showing the nature (symptoms) of the fault. Using the error
code, the user or the service man can readily find out how to correct the fault by simply referring to the User's Manual or service manual.
An error code may be either of the following two types:
- User Error Codes
A fault indicated as a user error code is one that can easily be corrected by the user, as by operating the machine. It takes the form of "#+number."
- Service Error Codes
If a fault calls for a service man for correction, it is indicated as a service man error code in the form of "##+number" or "SYSTEM ERROR E+number."
MEMO:
-
A service error code expressed in the form of "##+number" will not appear on the LCD, Error Tx Report, or Activity Report while the machine remains in factory
default state. To check a service error code, shift bit 0 of service soft switch #1 SSSW SW01 to '1'.
-
Display only the error codes which are newly incorporated in this machine as well as which require remedies unique to the product. For the causes and
countermeasures of other error codes, refer to the separate G3/G4 Facsimile Error Code List (Rev. 2).
16.5.2 User Error Code
16.5.2.1 User Error Code
No.
Tx/Rx
#0001
[Tx]
#0003
[Tx]
#0005
[Tx]
#0012
[Rx]
#0018
[Tx]
#0037
[Rx]
16.5.3 Service Error Code
16.5.3.1 Service Error Code
No.
Tx/Rx
##0100
[Tx]
##0101
[Tx]
##0102
[Tx]
##0104
[Tx]
##0106
[Rx]
##0107
[Rx]
##0109
[Tx]
##0114
[Rx]
##0200
[Rx]
##0201
[Tx]
##0224
[Tx]
##0228
[Rx]
##0232
[Tx]
##0237
[Rx]
##0261
[Tx]
##0282
[Tx]
##0283
[Tx]
##0288
[Tx]
##0289
[Tx]
##0290
[Tx]
Sensor No.
SR719
The leading edge of paper does not reach the ADF paper trailing edge sensor (SR719) within
3.2 sec after the ADF pickup motor starts positive rotation.
Description
an original has jammed.
tine-out for copying or sending/receiving a single page has occurred.
time-out for initial identification (T0/T1) has occurred.
recording paper is absent at the other party.
auto call initiation has failed.
image memory overflow at time of reception has occurred.
Description
at time of transmission, the procedural signal has been transmitted more than specified.
the modem speed does not match that of the other party.
at time of transmission, fall-back cannot be used.
at time of transmission, RTN or PIN is received.
at time of reception, the procedural signal is received for 6 sec while in wait for the signal.
at time of reception, the transmitting party cannot use fall-back.
at time of transmission, a signal other than DIS, DTC, FTT, CFR, or CRP is received, and the procedural signal has been sent
more than specified.
at time of reception, RTN is transmitted.
at time of reception, no image carrier is detected for 5 sec.
DCN is received outside the normal parity procedure.
Error has occurred on transmission procedural signal.
Error has occurred on images' information control.
encoding error has occurred.
decoding error has occurred.
system error has occurred.
at time of transmission, the procedural signal has been transmitted more than specified.
at time of transmission, the procedural signal has been transmitted more than specified.
after transmission of EOP, a signal other than PIN, PIP, MCF, RTP, or RTN has been received.
after transmission of EOM, a signal other than PIN, PIP, MCF, RTP, or RTN has been received.
after transmission of MPS, a signal other than PIN, PIP, MCF, RTP, or RTN has been received.
T-16-8
Description
T-16-9
T-16-10
Chapter 16
0020-9550
0020-4435
0020-4437
0020-4439
16-9
Advertisement
Chapters
Troubleshooting
