ZyXEL Communications MSC1000G User Manual page 904

Chapter 30 profile Commands
<it>
<prefix>
<start-num>
<suffix-len> =
softswitch
vbd off|on
<start-rtp-
port>
<end-rtp-
port>
<start-
timeout>
<short-
timeout>
<long-
timeout>
<init-
retrantime>
<min-
retrantime>
<max-
retrantime>
<retran-
window>
rfc2833
off|{on
<payload-
type>}
t38 off|on
904
= Set the inactivity-timer which is a keep-alive timer from the MG to the MGC (0
~65535 in units of 10 milliseconds).
If there are no messages from the MGC to the MG, after each inactivity-time
out, the MG sends a "notify" packet to the MGC. The units are 10 milliseconds.
=
Sets the ephemeral termination ID's prefix. It can be up to 31 characters.
Default is RTP/
= Specify the ephemeral termination ID's start number (0~999999999999999).
Specify how many digits to use for the ephemeral termination ID (0 ~ 15,
excluding the prefix).
=
Set this to zxss10-ss if the MGC is a ZTE ZXSS10 soft switch, set it to nortel-
cs1500 if the MGC is a Nortel CS1500, set it to nortel-cs2000 if the MGC is a
Nortel CS2000, otherwise set this to DEFVAL.
=
Turn "Voice Band Data" support on or off. Voice band data uses V.152 to define
settings for transmitting data in order to improve voice quality.
When you select on, whether or not V.152 is actually used depends on the
MGC's configuration.
=
Set the start (4000 ~ 64000) and end (5000 ~ 65000) of the UDP port range
for RTP protocol. This must be an even number.
Note: The end port must be more than 1000 greater than the start port.
=
Set the timeout period if the user doesn't send any DTMF signal after off-hook,
in seconds (0 ~ 99). 0 disables the timeout.
= Set the H.248 short time-out, in seconds (1 ~ 99). You define the short and
long timeout values and the MGC selects which to use.
=
Set the H.248 long time-out, in seconds (1 ~ 99). You define the short and
long timeout values and the MGC selects which to use.
= Set the duration between the first packet and the second packet before
registration (100 ~ 20000 milliseconds).
=
Set the minimum duration between any two packets after registration (100 ~
1000 milliseconds).
=
Set the maximum duration between any two packets after registration (1000 ~
20000 milliseconds).
= Set the total retransmit timer (1000 ~ 60000 milliseconds).
=
Set this to on to enable RFC 2833 for transmitting digits. When you enable RFC
2833 the system transmits DTMF signals as voice (in-band) or as separate RFC
2833 packets (out-of-band) according to the MGC's configuration.
When you enable RFC 2833, set the RTP payload (96~127) type for identifying
RFC 2833 packets.
Set this to no to not use RFC 2833 for transmitting DTMF signals. DTMF signals
can only be transmitted inband.
=
Set this to on to enable support for the T.38 fax relay standard.
When you enable T.38 the system uses T.30 to transmit faxes as voice (in-
band) or T.38 to transmit faxes as separate packets (out-of-band) according to
the MGC's
configuration.
Set this to off to disable support for the T.38 fax relay standard. The system
uses T.30 to transmit faxes as voice (in-band).
Management Switch Card User's Guide