Cisco ASR 9000 Series Command Reference Manual page 582

show subscriber session
PPPoE:PTA
PPPoE:PTA
PPPoE:PTA
PPPoE:PTA
PPPoE:PTA
PPPoE:PTA
PPPoE:PTA
PPPoE:PTA
PPPoE:PTA
PPPoE:PTA
PPPoE:PTA
PPPoE:PTA
PPPoE:PTA
PPPoE:PTA
PPPoE:PTA
PPPoE:PTA
PPPoE:PTA
PPPoE:PTA
PPPoE:PTA
PPPoE:PTA
PPPoE:PTA
PPPoE:PTA
PPPoE:PTA
PPPoE:PTA
PPPoE:PTA
PPPoE:PTA
PPPoE:PTA
PPPoE:PTA
PPPoE:PTA
PPPoE:PTA
PPPoE:PTA
PPPoE:PTA
PPPoE:PTA
This table describes the significant fields shown in the display.
Table 29: show subscriber session Field Descriptions
Field
Type
Interface
State
Subscriber IP Addr / Prefix LNS Address (Vrf)
This is the sample output for the show subscriber session command in EXEC mode:
RP/0/0/CPU0:server#show subscriber session all detail internal location 0/RSP0/CPU0
[14:09:18.244 UTC Thu Feb 13 2014] +++
Interface:
Circuit ID:
Remote ID:
Type:
IPv4 State:
IPv4 Address:
IPv4 Up helpers:
IPv4 Up requestors:
Cisco ASR 9000 Series Aggregation Services Router Broadband Network Gateway Command Reference,
Release 5.2.x
568
Gi0/1/0/0.1.pppoe10
Gi0/1/0/0.1.pppoe11
Gi0/1/0/0.1.pppoe12
Gi0/1/0/0.2.pppoe10
Gi0/1/0/0.2.pppoe11
Gi0/1/0/0.2.pppoe12
Gi0/1/0/0.3.pppoe10
Gi0/1/0/0.3.pppoe11
Gi0/1/0/0.3.pppoe12
Gi0/1/0/0.pppoe13
Gi0/1/0/0.pppoe14
Gi0/1/0/0.pppoe15
Gi0/1/0/0.1.pppoe13
Gi0/1/0/0.1.pppoe14
Gi0/1/0/0.1.pppoe15
Gi0/1/0/0.2.pppoe13
Gi0/1/0/0.2.pppoe14
Gi0/1/0/0.2.pppoe15
Gi0/1/0/0.3.pppoe13
Gi0/1/0/0.3.pppoe14
Gi0/1/0/0.3.pppoe15
Gi0/1/0/0.pppoe16
Gi0/1/0/0.pppoe17
Gi0/1/0/0.pppoe18
Gi0/1/0/0.1.pppoe16
Gi0/1/0/0.1.pppoe17
Gi0/1/0/0.1.pppoe18
Gi0/1/0/0.2.pppoe16
Gi0/1/0/0.2.pppoe17
Gi0/1/0/0.2.pppoe18
Gi0/1/0/0.3.pppoe16
Gi0/1/0/0.3.pppoe17
Gi0/1/0/0.3.pppoe18
Bundle-Ether1.1.ip1
Unknown
Unknown
IP: DHCP-trigger
Up, Thu Feb 13 13:12:07 2014
12.1.93.225, VRF: default
0x00000040 {IPSUB}
0x00000040 {IPSUB}
AC 100.0.0.1 (default)
AC 100.0.0.1 (default)
AC 100.0.0.1 (default)
AC 100.0.0.1 (default)
AC 100.0.0.1 (default)
AC 100.0.0.1 (default)
AC 100.0.0.1 (default)
AC 100.0.0.1 (default)
AC 100.0.0.1 (default)
AC 100.0.0.1 (default)
AC 100.0.0.1 (default)
AC 100.0.0.1 (default)
AC 100.0.0.1 (default)
AC 100.0.0.1 (default)
AC 100.0.0.1 (default)
AC 100.0.0.1 (default)
AC 100.0.0.1 (default)
AC 100.0.0.1 (default)
AC 100.0.0.1 (default)
AC 100.0.0.1 (default)
AC 100.0.0.1 (default)
AC 100.0.0.1 (default)
AC 100.0.0.1 (default)
AC 100.0.0.1 (default)
AC 100.0.0.1 (default)
AC 100.0.0.1 (default)
AC 100.0.0.1 (default)
AC 100.0.0.1 (default)
AC 100.0.0.1 (default)
AC 100.0.0.1 (default)
AC 100.0.0.1 (default)
AC 100.0.0.1 (default)
AC 100.0.0.1 (default)
Description
Specifies the subscriber session type.
Specifies the interface type.
Specifies the states of the subscriber session such as
initiate, connecting, connected, activated,
disconnected, idle, end.
Specifies the IP address of the subscriber interface.
Subscriber Commands