Bosch IRIS-Net User Manual

page of 994

/ 994
Contents
Table of Contents
Bookmarks

Table of Contents

Quick Links

Iris-Net

User Manual

Table of Contents

Summary of Contents for Bosch IRIS-Net

Page 1 IRIS-Net User Manual...
Page 3: Table Of Contents
IRIS-Net Table of Contents | en Table of contents IRIS-Net Preface Basics of IRIS-NET Introduction IRIS-Net Objects How to... Reference REMOTE AMPLIFIER P-Series RCM-26 RCM-28 RCM-810 REV WIRELESS MICROPHONE SYSTEM Introduction REV Device REV Control Panel Setup & Control DIGITAL MATRIX...
Page 4: Table Of Contents
IRIS-Net Table of Contents | en PMX-2P500 PAVIRO 10.1 PVA-4CR12 10.2 PVA-4R24 10.3 PVA-15CST 10.4 PVA-CSK 10.5 PVA-2P500 Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 5: Iris-Net
PA systems. To get the most out of the IRIS-Net software we recommend that you read through all the topics in this help file carefully.
Page 6: Basics Of Iris-Net
Select "setup.exe" and click on the Open button. The IRIS-Net installation program starts. Follow the instructions of the installation program. When the installation is finished you can start IRIS-Net from Windows via Start > All Programs > IRIS-Net > IRISNet. IRIS-Net Directory Structure This section provides information about IRIS-Net directories and the contained files which, after installing the software package, are stored on your computer’s hard disk.
Page 7 \Controls. This directory holds all IRIS-Net controls. Controls are composed of system files that are of no direct relevance for the user and bitmap graphics. The latter define the looks of a control. Creating and adding custom bitmaps which then represent your own specific controls is possible.
Page 8 The Default Presets F01, F02, O01, O02 and U01 - U06 are located in this folder. Default presets are for initializing a power amplifier as soon as it is included in an IRIS-Net worksheet via drag-and-drop. The subfolders contain factory- presets for speaker cabinets.
Page 9 All other subdirectories contain IRIS-Net system files, which are of no further significance for the user. As a matter of fact, the opposite is the case. Altering the contents of these subfolders is categorically not advisable.
Page 10: Introduction
Use the left mouse button and click on Add Layer. This creates a new page (layer). Now, you have to name it (e.g. Control Page). IRIS-Net allows the use of up to 32 layers. Designing User Control Panels. The IRIS-Net software allows the creation of various control panels, which can be customized to suit the needs of a project and the needs of the users.
Page 11 Configuration Of A Remote Power Amplifier System Using a NetMax N8000 System Controller Start The IRIS-Net Software. IRIS-Net starts creating a new project and opens an empty "Configuration Page" worksheet. Saving. Name your new project before saving (File Save). Creating a separate folder for each project in the directory \IRIS-Net\Projects\ is strongly recommended.
Page 12 Use the left mouse button and click on Add Layer. This creates a new page (layer). Now, you have to name it (e.g. Control Page). IRIS-Net allows the use of up to 32 layers. 10. Designing User Control Panels. The IRIS-Net software allows the creation of various control panels, which can be customized to suit the needs of a project and the needs of the users.
Page 13 How to edit an existing project? This paragraph explains how to edit a project that already exists. Due to the fact that IRIS-Net provides the possibility for different users to have different access permissions assigned within a single project, editing options might be highly restricted by the Administrator.
Page 14 A connection will be established only with selected devices. The IP address of the device in IRIS-Net. Connection fails, if the IP address specified in IRIS-Net differs from the actual IP address of the unit.
Page 15 IRIS-Net IRIS-Net | en CAN On-line Dialog Element Description Name of the Remote Amplifier. Indicates the current connection status of the device. Name of the PC-to-Remote Amplifier interface. Reads all settings and presets of the Remote Amplifier(s). Writes all settings and presets into memory of the Remote Amplifier(s).
Page 16 IRIS-Net IRIS-Net | en Element Description A project's password protection can be activated or deactivated. If a user has a "blank" password, on opening, the project is automatically loaded with his access rights. Username. The user's password. This column is only visible when the administrator account is being used.
Page 17 IRIS-Net IRIS-Net | en This field allows entering the numbers that correspond to the layers which are accessible for the user. Several layers have to be separated by commas. Using hyphens for separation indicates that the layers are interrelated. Opens the "Layers" Window which allows selecting those layers that are accessible for a user.
Page 18: Adding Devices
Opening and closing the group lists is possible by clicking on the arrow icon at the right. The contents of the devices list depends on the actually installed IRIS-Net version and on the devices that are actually available, i.e.
Page 19 IRIS-Net | en To add devices to an IRIS-Net project, first select the desired device in the Object Bar (or from the Devices window) and then drag and drop it into the worksheet. A dialog box opens, which lets you specify device-related settings such as amount of desired devices, address range, and interfaces.
Page 20 Opening and closing the group lists is possible through clicking on the arrow icon in the top right corner. The content of the interfaces list depends on the actually installed IRIS-Net version, i.e. it may differ from the list as shown in the following illustration.
Page 21 Button Controls Element Name Description Push Button Pushbutton for executing a function or for opening an IRIS-Net dialog box Radio Button Several pushbuttons that trigger each other, e.g. for switching or changing functions or parameters Switch Button Switch button for switching between two states, e.g. On/Off Rocker Switch Rocker switch for switching between two states, e.g.
Page 22 IRIS-Net IRIS-Net | en Mini Routing Routing block for setting the output routing in signal flow diagrams Spin Edit Windows Spin Edit for entering values via Up/Down selection buttons or direct editing Display Controls Element Name Description Display Value Display field for displaying values or text, e.g. names...
Page 23 IRIS-Net IRIS-Net | en ChannelEQ PEQ user panel for a single or a group of Channel EQs Mini Delay Delay block for displaying delay settings Mini Dynamics Dynamic block for displaying settings of dynamic processors Mini MasterEQ Master EQ Block for displaying Equalizer settings...
Page 24 Switch button shall be used to simultaneously switch several amps of a project on or off. Drag and drop a Switch button from the list into the IRIS-Net worksheet. Click with the right mouse button on the Switch button and select Modify Properties from the switch button’s contextual menu.
Page 25 User Controls are links between a single or several Control Elements and a single or several Bitmaps. In addition to using the User Controls that are included in the IRIS-Net package you can also create custom User Controls and save them to disc.
Page 26 The Locally Used category holds all User Controls, which are used in the current project. The Globally Available category holds all User Controls that are stored in the IRIS-Net User Controls folder. The content of the list depends on the actually installed IRIS-Net version and on the devices that are currently available, i.e. it may differ from the list as shown in the following illustration.
Page 27 IRIS-Net IRIS-Net | en Group_LEDs_01 The three LEDs on the top indicate clipping (CLIP) or whether the limiter (LIMIT) or the compressor (COMP) of the DSP is active. The two LEDs on the bottom indicate that the unit entered Protection (PROT) mode or that the amp’s limiter (LIMIT) has been activated.
Page 28 IRIS-Net IRIS-Net | en ShelvingEQ_Freq_Gain_02 Equalizer panel with label field for the RCM-24 Remote Amp. Pre-set for band 5 of the channel equalizer. Equalizer type, frequency, gain and BYPASS can be set. Possible Connections: RCM- 24-Amp. System_Supervision_01 The amplifier LED lights red when in Standby or Protection mode.
Page 29 IRIS-Net IRIS-Net | en RCM-26_Master_EQ_Pa Equalizer panel with label field for the RCM-26 Remote nel_01 Amp. Use the Master EQ button to open the Master EQ dialog. Possible Connections: RCM-26-Amp- Channel. RCM-26_Master_Panel_ Fader and MUTE button for controlling the amplifier.
Page 30 IRIS-Net IRIS-Net | en RCM-26_Memory_Panel Load user memory presets 1...6 or save to user memory 1...6. Number and name of the currently active user memory is being indicated. Editing preset title is possible. Possible Connections: RCM-26-Amp. RCM-26_Supervision_Fl CAN address and name of amplifier is indicated. The...
Page 31 IRIS-Net IRIS-Net | en RCM-28_Memory_Panel_01 Load user memory presets 1...10 or save to user memory 1...10. Number and name of the currently active user memory is being indicated. Possible Connections: RCM-28-Amp. RCM-28_Memory_Panel_02, 03 and 04 Load user memory presets 1...10 (or 11..20 or 21..30) or save to user...
Page 32 IRIS-Net IRIS-Net | en Delay_Panel_03 Delay value and bypass for the master delay of a remote amp. Possible Connections: RCM- 24-Amp-Channel, RCM-26-Amp- Channel Group_Panel_01 These three LEDs indicate clipping (CLIP) or whether the limiter (LIMIT) or the compressor (COMP) of the DSP is active. Fader and MUTE buttons for controlling and LED bar graph meter for monitoring the amp’s output levels (maximum of both...
Page 33 IRIS-Net IRIS-Net | en Group_Panel_GainTrim_ These three LEDs indicate clipping (CLIP) or whether the limiter (LIMIT) or the compressor (COMP) of the DSP is active. Fader and MUTE button for controlling the amplifier. The LED bar graph meter is for monitoring the amp’s output levels (maximum of both channels).
Page 34 IRIS-Net IRIS-Net | en Master_Panel_01 Switches the amp’s power on or off with safety dialog when powering off. Fader and MUTE button for controlling the amplifier. Possible Connections: RCM-24-Amp, RCM-26-Amp Master_Panel_02 Switches the amp’s power on or off with safety dialog when powering off.
Page 35 IRIS-Net IRIS-Net | en System_POWER_MUTE_ Power-on/off and mute a single or a group of amps. Possible Connections: RCM-24-Amp, RCM-26-Amp System_Supervision_02 The amplifier LED lights red when at least one of the errors selected in the dialog Supervision & Test occurs. Otherwise, the LED lights green.
Page 36 IRIS-Net IRIS-Net | en Level_Panel_ Fader and MUTE button for controlling and LED bar graph meter for monitoring a input/ output level. Possible Connections: N8000.DSP.AnalogIn.ChX, N8000.DSP.AnalogMicIn.ChX, N8000.DSP.AnalogOut.ChX, N8000.DSP.AutoMixer.ChInX, N8000.DSP.AutoMixer.ChOutX, N8000.DSP.DigitalIn.ChX Level_Panel_ Fader, MUTE button and INV button for controlling and LED bar graph meter for monitoring a input/output level.
Page 37 IRIS-Net IRIS-Net | en Miscellaneous User Controls Picture Name Description Labelled_SPEAKER General loudspeaker with label. Possible Connections: - none - EOL User Controls Picture Name Description EOL_LED_Panel_0 The Short LED lights red if the voltage at the amplifier‘s output 1, 2, 3 or 4 is below the EOL VOLTAGE threshold set in the Supervision &...
Page 38 The example shows how an PowerH_Panel_01 is used to control an amplifier. Use Drag & Drop to include an PowerH_Panel_01_1 in the IRIS-Net worksheet. Click with the right mouse button on the Panel select Administrate Connection from the contextual menu. The “Connections for PowerH_Panel_01_1”...
Page 39 IRIS-Net (e.g. Rack_15HU). You can copy new Bitmaps into IRISNet’s Bitmaps Folder or you can add a new graphic to the IRIS-Net worksheet using Drag & Drop. Just select the desired file in the Windows Explorer and drag it over into the worksheet.
Page 40 Adding Textboxes Textboxes, which can be used to create text labels in an IRIS-Net project, are to be found under the Objects Bar category Textboxes and in the separate Textboxes window. This window opens when you choose Add Textboxes from the IRISNet Configuration menu or from the contextual menu within the IRIS-Net worksheet.
Page 41 Using Groups IRIS-Net provides Groups as special control elements. Groups are used for combining a variety of objects. Actions applied to a group are applied to all objects of the group. An object can be included in various groups at the same time.
Page 42 IRIS-Net works- heet. All objects of the object-class currently selected in the dropdown field “class” are added to the group. Sets the font used for the group icon label in the IRIS-Net worksheet. Bosch Security Systems B.V. User Manual...
Page 43 IRIS-Net IRIS-Net | en Sets the background color of the group icon in the IRIS-Net worksheet. Selects the dialog that will be opened when the user double-clicks the group icon in the IRIS-Net worksheet. Which dialogs are available for selection depends on the devices used in the project.
Page 44 Cancels the current object selection and closes the “Connections for...” window. Editing Object visibility IRIS-Net offers the possibility to individually specify the visibility status of each object per layer. This option greatly simplifies the design of projects which include layers with similar appearance. Creating an object with its visibility flag unchecked for all layers hides the object from the entire project.
Page 45: Software Update
The Project Info Dialog is accessed by selecting the menu entry Info in the Main-Menu. Software update If a Internet connection is available, updating IRIS-Net is possible via Internet. The Software Update Dialog is accessed by selecting the menu entry ? > Search for Updates ...
Page 46 The Settings dialog allows the user to edit attributes of IRIS-Net. Amongst others, the user can specify whether and if so, which events shall be included in the IRIS-Net event log. The Settings dialog is accessed from the menu Edit >...
Page 47 IRIS-Net | en Element Description Start with last loaded Project Specifies whether the last opened project shall be reopened when IRIS-Net is launched. Display Username on Login Specifies whether the user name has to be entered in addition to the password when opening protected project files.
Page 48 IRIS-Net IRIS-Net | en Element Description This field is for entering the speaker cabinet’s average nominal SPL (see data sheet). Enter the power output of the amplifier in this field. Since the amp’s actual outputted power depends on the impedance of the load connected, the entered value has to match the load that is actually connected.
Page 49 IRIS-Net IRIS-Net | en Element Description Power Limit Enter the maximum power consumption of the loudspeaker cabinet used (refer to datasheet) in this field. Nominal Impedance Enter the impedance of the loudspeaker cabinet used (refer to datasheet) in this field.
Page 50 IRIS-Net IRIS-Net | en Element Description Creates a new event, which is added at the end of the event list. Events marked in the Event list will be deleted. Opens the Event Parameters window for editing the parameters of the selected event.
Page 51 IRIS-Net IRIS-Net | en Element Description The event is scheduled to be activated only once on a specific day and at a specific time. The event is scheduled to be activated once a year on a specific day of the year and at a specific time.
Page 52 IRIS-Net IRIS-Net | en Element Description Creates a new Day Program and adds it to the Day Program list. The Day Programs selected in the Day Program list will be deleted. New Entry creates a new entry in the event list of the currently selected Day Program. New events are numbered consecutively with their time being set to 12:00:00 as a standard.
Page 53 IRIS-Net IRIS-Net | en The Set Time window allows setting the time for an event in the Day Program. Setting the desired time is possible either by turning the hour hand of the conventionalized clock using the mouse or through entering the numerical value in the time field.
Page 54 IRIS-Net IRIS-Net | en Opens the Dayprog Selection Dialog window for selecting the Day Program to be executed during the period corresponding to the holiday currently selected in the holiday list. Copy a single or various marked holidays from the holiday list. Copied holidays can be pasted to the end of the holiday list.
Page 55 Macros This window allows creating and editing macros. Macros are used to change the status of objects. Objects can be devices (e.g. a N8000 System Controller) as well as elements in IRIS-Net (e.g. controls). Bosch Security Systems B.V. User Manual...
Page 56 IRIS-Net IRIS-Net | en Element Description Creates a new macro. The macro gets added to the end of the macro list. The macros that have been selected in the macro list are deleted. Opens the Operation window which allows selecting variables, whose value is to be set by the macro selected in the macro list.
Page 57 IRIS-Net IRIS-Net | en Element Description Only functions that include the text entered here are being displayed in the functions list, which is shown in the left part of the window. Check if filter should be case sensitive. Selecting a single or various object types is possible. Only objects that comply with the selected types are shown in the list of objects, which greatly simplifies finding the desired object quickly.
Page 58 IRIS-Net IRIS-Net | en Element Description Creates a new Trigger. The Trigger is added at the end of the Trigger List. All Triggers selected in the Trigger List will be deleted. Opens the Condition Selection Dialog Window, which lets the user assign a condition to the Trigger that is currently selected in the Trigger List.
Page 59 IRIS-Net IRIS-Net | en The ON Macro Selection Dialog Window lets the user select the macro that will be executed when the status of the condition changes from "false" to "true". Equally, the OFF Macro Selection Dialog Window lets the user select the macro that will be executed when the status of the condition changes from "true"...
Page 60 IRIS-Net IRIS-Net | en Conditions Element Description Creates a new Condition. The Condition is added at the end of the Condition List. All Conditions selected in the Condition List will be deleted. Opens the Condition Properties Window, which lets the user assign parameters to the Condition.
Page 61 IRIS-Net IRIS-Net | en – "Is lower": a condition is true when a variable is truly lower than a specific value. Otherwise, the condition is false. – "Timespan": within a certain period of time the condition is true either exactly once or periodically (in adjustable intervals) for a specified time span.
Page 62 IRIS-Net IRIS-Net | en Timed Condition A Timed Condition is always defined by a Period of Time, during which the Condition is "true" for a specified Duration. The Period of Time may occur once (Onetime) or periodically (every ...). Appropriately, the Duration should not exceed the selected Period of Time.
Page 63 IRIS-Net IRIS-Net | en Starting immediately from the beginning of the Period of Time, the Condition is recurringly "true" every x week(s) during the Duration. Starting immediately from the beginning of the Period of Time, the Condition is "true" for the Duration, if the first day of the Period of Time falls on the selected weekday.
Page 64 IRIS-Net IRIS-Net | en Using the Scene Editor A Scene consists of a freely configurable number of actions. Examples for actions that can be part of a Scene are: DSP parameters, GPIO settings, remote amplifier parameters or the loading of presets.
Page 65 (i.e., an invalid or conflicting IP address). Use the OCA Scan dialog (see Searching OMNEO-devices on the Ethernet, page 66) to scan for OMNEO devices. Notice! Firewalls can cause problems when using the IRIS-Net Device Scan. Selecting the entry Device Scan in the Tools menu lets you access the Device Scan dialog. Element...
Page 66 IRIS-Net IRIS-Net | en NETWORK Shows the network settings of the device in the format: IP address / subnet mask GW: gateway SETTINGS address SYSTEM NAME Shows the system name of the device SOFTWARE Shows the firmware version of the device...
Page 67 HINT: There are two drag & drop functionalities for devices listed here. The first option is to drop a device from the OCA Scan dialog into the IRIS-Net worksheet. A new RCM-28 remote amplifier will be created and automatically linked to the dropped device. The second option is to drop a device from the OCA Scan dialog onto an existing RCM-28 remote amplifier in the worksheet.
Page 68 Clicking onto this button closes the OCA Scan dialog. Using the PA Event Log The Event Log chronologically lists internal IRIS-Net events and events that occurred during the operation of devices that are included in the project. This, for example, aids when troubleshooting the system.
Page 69 IRIS-Net IRIS-Net | en The type of an event. The device that triggered the event. The sub-system of the device that triggered the event. Textual description of an event. Event Logging Setup This dialog allows specifying the event type to appear in the Log File. Events are defined as problems (errors) that occurred within the system, but also messages providing information about the system status or changes in the status.
Page 70 Changing available devices The devices shown in the Object List can be customized. Use the IRIS-Net Device Options dialog window. The dialog window opens automatically the first time IRIS-Net is run. For later customization, you can find the dialog window in the menu Edit >...
Page 71 Up to 100 devices can be connected to a single CAN-Bus with a maximum total cable length of 1,000 metres. An additional CAN-bus is needed for controlling more than 100 devices while the IRIS-Net software will support a total of 250 amplifiers.
Page 72 IRIS-Net IRIS-Net | en In addition to the CAN-bus data signal, network cabling also carries the balanced monitor audio signal for monitoring the power amp inputs and outputs. This monitor-bus allows software-controlled monitoring of the input and output si- gnals of all power amps that are included in the remote network, without the need for additional wiring. This balanced line level audio signal is present at the UCC1’s XLR-type MONITOR Output connector.
Page 73 IRIS-Net IRIS-Net | en With all remote power amps, the factory data rate setting defaults to 10 kbit/s. The use of repeaters is generally recom- mended when the bus-length exceeds 1,000 m. CAN-Bus Cable Specifications According to the ISO 11898-2 standard, CAN-bus data transfer cabling has to be carried out using Twisted-Pair cables with or without shielding providing a characteristic impedance of 120 Ω.
Page 74 A Remote Power Amplifier System is a computer-controlled audio system that consists of a single or multiple Remote Power Amps and a single or multiple PCs with the IRIS-Net software. Communication is established via CAN Remote Control Network. An UCC1 USB-CAN Converter (or e.g. a Netmax N8000 System Controller) serves as interface for linking to the PC.
Page 75 To configure the Remote Power Amplifier System according to your requirements, start the IRIS-Net Software and open the corresponding project-file. Please also bear in mind the following chapters, which lay out the procedures when creating and editing IRIS-Net projects.
Page 76 (unintended) baud rate change. For activating this option select "Modify Properties" from the amplifiers context menu in IRIS-Net. Change the value of property Baud rate freeze from 0 to 1. If Baud rate freeze is activated, the baud rate can be changed neither via Address-Switch nor via IRIS-Net. For changing baud rate you have to deactivate Baud rate freeze.
Page 77: Main Window
Description Title Bar The title bar shows the name of the currently opened project file and IRIS-Net. "Noname" is displayed when opening a new project file or when the current project has not been saved yet. The Minimize, Maximize/Restore Size and Close/Quit IRIS-Net buttons are located on the right.
Page 78 IRIS-Net IRIS-Net | en Status Window The Status Window displays IRIS-Net system status messages. Additionally, the name of the currently logged-in user is shown underneath the Status Window. Worksheet In the Worksheet, the user can arrange control and display panels of a project by dragging objects out of the Object List and dropping them into the Worksheet.
Page 79 IRIS-Net IRIS-Net | en Status Bar Shows the status bar at the bottom of the IRIS-Net workspace window. Object List Shows the object list at the left of the IRIS-Net workspace window. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 80 Add Layer A click on Add Layer lets you add a new page (layer) to the IRIS-Net project. A new register (Layer x) is created in the IRIS-Net worksheet. Assign a meaningful name to the new register, e.g.
Page 81 IRIS-Net IRIS-Net | en PA Event Log Opens the window PA Event Log OCA Scan Opens the window OCA Scan. Dante Configuration Opens the window Network View. In this window you can edit the routing in your Dante network. Menu “RCM-24”...
Page 82 Project Info Opens the window Project Info Help Topics Opens IRIS-Net help (this document) Quick Start Guide... Opens the IRIS-Net Quick Start Guide. Search for Updates ... Opens the Software Update dialog. About IRIS..Shows the current application software version.
Page 83 Controls PushButton The IRIS-Net Control of the type "PushButton" is the equivalent of a button. The button has two states: pressed and unpressed. Left-clicking on the "PushButton" Control activates the "pressed" state. The "unpressed" state is restored immediately after releasing the mouse button. The button's appearance in both states can be freely configured.
Page 84 Switching between Controls for editing is possible if a variety of Controls of the type "PushButton" are used in a project. The currently selected PushButton is deleted in the IRIS-Net project. Caption Text label of the PushButton. The entered text is always displayed centered.
Page 85 Opens the "Properties for PushButton" dialog. Property Description bitmap Path and filename of bitmap used for button. Path must be entered relative to \IRIS-Net. caption Caption of button Capture accel Only used if mode is "increment" or "decrement". Every capture period ms the new value is...
Page 86 Absolute or relative path description is name> \SeparateRooms.scn possible. Open a template template=<templateNa template=N8000_PEQ_5 See directory \IRIS-Net\Templates for me><"Window Title"> Band_Mono "PEQ 5 available tem- plates. "Window Title" is Band" %c displayed in the title bar of the template window..
Page 87 IRIS-Net IRIS-Net | en Going online/offline *online=<0/1> *online=1 use 1 for going online, use 0 for going offline Change user of Change current Change current Entering the password of the user is IRIS-Net user=<UserName> user=NewUser1 not required when "logging in" via PushButton.
Page 88 IRIS-Net IRIS-Net | en Template Description ArrayPEQ_5band_UI DSP600DSPUI DSP600UI DSP600Userpanel DSPUI DX38UI DX46DSPUI DX46UI DX46Userpanel InputGEQ_31band_UI InputPEQ_10band_UI Master EQ UI x Band x = 3, 4, 5, 6 N8000_Delay_xms x = 10, 100, 500, 2000 N8000_GEQ_xWay_Mono x = 10, 15, 31...
Page 89 IRIS-Net IRIS-Net | en Description Config & Info This page provides information about the amplifier and allows making several basic settings as well as programming control functions. The DSP page provides an overview plus access to all DSP functions (Filter, Delay, X-Over, and Dynamics) of the amplifier.
Page 90 IRIS-Net IRIS-Net | en Element Description The flow diagram selector lets you select different function blocks, where the actually selected block is displayed in a yellow engaged field. Select A or B if the setting should be valid for the corresponding channel of the connected amplifier.
Page 91 This loads and afterwards displays all DSP parameters that are stored within that file. IRIS-Net allows importing loudspeaker presets that have been created in Electro-Voice RACE by clicking onto the button IMPORT RACE FILE to open the following dialog box.
Page 92 ”speaker files” (*.spk), contain factory-measured frequency- and phase responses of all common Electro- Voice and DYNACORD loudspeaker systems. Some examples are provided in the IRIS-Net directory Speaker Files. The speaker data as well as any settings made in this window have no direct influence on the transfer function of the amps.
Page 93 IRIS-Net IRIS-Net | en The DSP page provides an overview plus access to all DSP functions (Filter, Delay, X-Over, Limiters) of the amplifier. Speaker This page allows loading and displaying speaker data. Load This page provides access to several settings for impedance/load monitoring and impedance testing.
Page 94 IRIS-Net IRIS-Net | en Element Description The flow diagram selector lets you select different function blocks, where the actually selected block is displayed in a yellow engaged field. Here you can assign the output channel routing. The A and B buttons allow selecting the input signal for the corresponding output channel.
Page 95 IRIS-Net IRIS-Net | en FIR Filter Block: This block represents the FIR Filter within the corresponding output channel. The graph shows the frequency response that results from the set FIR parameters. The LED indicate if the FIR Filter is being used.
Page 96 ”speaker files” (*.spk), contain factory-measured frequency- and phase responses of all common Electro- Voice and DYNACORD loudspeaker systems. Some examples are provided in the IRIS-Net directory Speaker Files. The speaker data as well as any settings made in this window have no direct influence on the transfer function of the amps.
Page 97 The "Master EQ" control panel is available in three different versions - offering three, four, or five band EQs. Any individual Remote Amplifier's equalizer band that exists in the IRIS-Net project may be assigned to each of the Master EQ bands. The control panel is accessed via a Push Button or a Group. The desired devices with equalizer bands to be controlled assigned to, have to be linked to the Push Button or the Group via the menu item "Administrate Connection"...
Page 98 IRIS-Net IRIS-Net | en N8000_GEQ_xWay The "N8000_GEQ_xWay" control panel is available in three different versions - offering 10, 15, or 31 band GEQs. It is the equivalent of the DSP Block Window "GEQ" of a N8000. The control panel is accessed via a Push Button or a Group and is used for the synchronized control of several N8000.
Page 99 IRIS-Net IRIS-Net | en N8000_LSC_xWay_Mono The "N8000_LSC_xWay" control panel is available in five different versions - offering one, two, three, four, or five channels. It is the equivalent of the DSP Block Window "Monaural Loudspeaker Controller" of a N8000. The Loudspeaker Controllers to be controlled have to be linked to the Push Button or the Group via the menu item "Administrate Connection"...
Page 100 IRIS-Net IRIS-Net | en N8000_ToneControl_Mono The "N8000_ToneControl_Mono" control panel is the equivalent of the DSP Block Window "Tone Control Mono" of a N8000. N8000_ToneGenerator_Mono The "N8000_ToneGenerator_Mono" control panel is the equivalent of the DSP Block Window "Tone Generator Mono" of a N8000.
Page 101: Remote Amplifier
P-Series Introduction The IRIS-Net software (Intelligent Remote & Integrated Supervision) runs under Windows and allows configuring, controlling and monitoring a complete PA-system from a single or from several PCs. Any operational status, e.g. power- on, temperature, level, limiting, activation of protections, deviation of the output impedance, etc., are centrally recorded and displayed, which offers the opportunity to react and interfere even before the occurrence of critical operational states.
Page 102 Each power amplifier employs an RCM-24 Remote Control module, which allows integration into a Remote Control Net- work consisting of up to 100 power amps. Detailed information on the individual modules is provided in the corresponding manuals. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 103 All parameters, i.e. settings and presets, of (a) RCM-24 module(s) will be shown. Writes the selected parameters into the RCM-24 module(s). Reads the selected parameters out of the RCM-24 module(s). Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 104 Displays the differences in the parameters found during the comparison. TESTING THE CONNECTED LOUDSPEAKER SYSTEMS IRIS-Net allows convenient analysis of all loudspeaker systems connected to remote amplifiers used in a project. All remote amplifiers are listed in the RCM-24 System Check Window.
Page 105 IRIS-Net REMOTE AMPLIFIER | en Name of the amplifier consisting of CAN address, internal IRIS-Net name, and type of amplifier. The current status of the amplifier. The current status of the amplifier's channel "A". The current status of the amplifier's channel "B".
Page 106 The name of a remote amplifier. The name of input channel "A". The name of input channel "B". The name of output channel "A". The name of output channel "B". Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 107 Amplifier Type field and enter the desired name. Press Return on the keyboard to acknowledge the entered name. HINT: Entering amplifier names is also possible with in the Setup & Control Panel on the Config & Info page. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 108 In case of thermal over- load, you have to wait some time until the amplifier automatically re-enters normal operation. (see also Supervision & Test for additional fault information) Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 109 Clicking this switch activates the STATUS indicator on the amplifier’s rear panel as well as in the amplifier’s front panel window in the IRIS-Net software. Normally, the STATUS indicator blinks only during serial communication. Once the STATUS switch is engaged, the STATUS indicator blinks in a steady but fast sequence.
Page 110 POWER lights whenever the amplifier is powered-on and ready for operation. If neither one of the indicators lights, the amplifier is either off-line or powered-off. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 111 The DSP page provides an overview plus access to all DSP functions (Filter, Delay, X-Over, Dynamics) of the amplifier. Speaker This page allows loading and displaying speaker data. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 112 The Config & Info window provides information and basic settings for the selected amplifier. Additionally, editing labels and configuring control functions is possible as well. To select the page click onto the Configuration & Information register in the Setup & Control Window. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 113 IN2 ON: Preset U03 (closing the contact of control input 2 selects preset U03) – IN2 OFF: Preset U02 (opening the contact of control input 2 selects preset U02) Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 114 ON and OFF. The entries in the corresponding lines specify which OUT 2 ON status results in the closing (ON) or opening (OFF) of a contact. OUT 2 OFF Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 115 Receive Job Nr. 4: Preset U02 (receiving Job Code 4 selects preset U02) Element Default Range Description 1...10 Here, you can specify which incoming job code numbers a specific amplifier recognizes. Entering random numbers between 0 and 1023 is possible. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 116 Here you can set the different function parameters. For more information, please refer to the table "Output and Transmit Job Conditions". (empty) Certain functions allow specifying optional parameter values. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 117 = infinite) Output and Transmit Job Conditions: The following table lists all amplifier statuses that can be used for triggering control outputs or for sending Transmit Job Codes. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 118 1 - pattern Memory flags do not match the selected bit-pattern Preset U01 - U08, F01 Specified preset selected Other than the specified preset selected Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 119 The FLOW DIAGRAM window opens when clicking on the first, fourth or eighth block in the Flow Diagram Selector. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 120 Clicking with the right mouse button opens the Copy & Paste menu, which allows copying all parameters of the corresponding Master Delay block to any other Master Delay block within the same project. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 121 Clicking the MUTE button once again with the left mouse button disables the mute-function and the amplifier output is again active. The MUTE button is virtually disengaged and not lit. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 122 This field allows assigning a name to a preset before saving it. The name is stored as well and is displayed in the status line NAME after performing a RECALL. STORE saves all momentary set DSP parameters together with the entered name into the specified preset. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 123 Import / Export of Preset Files IRIS-Net allows the storing of all DSP parameters of an amplifier together with the according preset name in a file, and to load amplifier parameters from these files. Therefore, IRIS-Net creates a sub-directory \Presets during installation, where all factory-presets are saved in to.
Page 124 The Master-EQ is selected by clicking on the second block of the flow diagram selector or by double clicking on the MASTER EQ block in the full-scale flow diagram. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 125 A click with the right mouse button opens the “Copy & Paste” menu, which allows convenient copying all EQs of the corresponding input to any other EQ-filter bank within the same project. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 126 BYPASS switches the corresponding filter ON (not engaged) or OFF (engaged), which allows for quick A / B-evaluation of the actual effect that a filter has on the sound. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 127 A click with the right mouse button on this field opens the Copy & Paste menu, which allows copying all master delay parameters of the selected input to any other master delay within the same project. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 128 The Channel-EQ is selected by clicking on the fifth block of the flow diagram selector or by double clicking on the CHANNEL EQ block in the full-scale flow diagram. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 129 A click with the right mouse button opens the Copy & Paste menu, which allows convenient copying all EQs of the corresponding output to any other EQ-filter bank within the same project. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 130 BYPASS switches the corresponding filter ON (not engaged) or OFF (engaged), which allows for quick A / B-evaluation of the actual effect that a filter has on the sound. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 131 Element Description Switches between frequency (magnitude) and phase response (phase) indication Switch for selecting dB-axis scaling of 25 dB (± 12.5 dB) or 50 dB (± 25 dB) Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 132 HI-PASS filters within the same project. Bessel 12dB, Butterworth 12dB, Linkwitz/Riley 12dB, Bessel 18dB, Butterworth 18dB, Bessel 24dB, Butter- worth 24dB, Linkwitz/Riley 24dB FREQ: 20 Hz...20 kHz Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 133 The effect of the polarity parameter becomes obvious when displaying the summed signal of the two amplifier channels (switch set to Sum). Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 134 Clicking onto the seventh block in the Flow Diagram Selector or double clicking onto the DYNAMICS block in the large flow diagram opens the dynamics window. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 135 250 ms 50...999 ms RELEASE determines how fast the compressor returns to normal amplification, after the audio signal level declined the threshold. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 136 Limiter Threshold. Thresh The margin level indicates the distance between signal level and the set absolute level. The displayed margin always relates to the highest actual signal level reading. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 137 A compressor’s / limiter’s title lights in color as soon as the mouse cursor is positioned on top of the corresponding white dot to provide improved overview and handling. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 138 ”speaker files” (*.spk), contain factory-measured frequency- and phase responses of all common Electro- Voice loudspeaker systems. Some examples are provided in the IRIS-Net directory Speaker Files. The speaker data as well as any settings made in this window have no direct influence on the transfer function of the amps.
Page 139 Clicking the button LOAD SPEAKER FILE opens a dialog that allows the selection of the desired speaker file. Different loudspeaker files can be found in the Speaker files IRIS-Net folder. The name of the loaded loudspeaker model is shown in the black-shaded field on the right.
Page 140 LOW THRESH sets the lower limit of the allowable impedance kOhm range (= maximum load). Once this value is fallen short of, a SHORTED fault message (line short-circuit) appears in the Amplifier Control Panel. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 141 A click on the Supervision & Test tab selects the page while in the Setup & Control Window. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 142 Unit selects the unit of the generator level. If the push-button is not engaged, the level is shown in dBu. When it is engaged, the output voltage is indicated in volts. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 143 The Protect indicator lights for approx. 2 seconds during power-on operation. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 144 Once detected, a ground fault is stored in the power amp. After remedying the cause of the ground fault, press the CLEAR button to clear the indication. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 145 DEMO SYSTEM SMALL The IRIS-Net project ”Demo System Small” is an example of a small EV remote amplifier system installation. This 2-way stereo system includes the following equipment: 2x P3000RL, 2x Sx300 and 2x Sb121. This example is meant to provide the necessary information to understand the entire set-up and configuration flexibility offered through the use of the IRIS-Net software for such a system.
Page 146 IRIS-Net REMOTE AMPLIFIER | en Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 147 IRIS-Net REMOTE AMPLIFIER | en Amplifier Control Panel DSP Parameter Window Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 148 IRIS-Net REMOTE AMPLIFIER | en Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 149 IRIS-Net REMOTE AMPLIFIER | en Layer 2: Control Page Config & Info Window Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 150 IRIS-Net REMOTE AMPLIFIER | en XLCDEMOPROJECT Layer 1: Administration Page Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 151 IRIS-Net REMOTE AMPLIFIER | en Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 152 IRIS-Net REMOTE AMPLIFIER | en Layer 2: Amplifiers Page Layer 3: Speaker Supervision Page Layer 4: Speaker Mutes Page Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 153 IRIS-Net REMOTE AMPLIFIER | en Layer 5: Control Page Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 154 The question mark "?" can be utilized to query parameter settings or commands of the corresponding level. To step one level down you have to enter "../". The following table lists the ASCII Control Protocol commands with brief explanations. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 155 Active remote connection is shown as address in brackets before the prompt. Commands for Level Indication /METER /AUTO R / W ON, OFF Setting for automatic level meters transmission via CAN Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 156 R / W 0...40 [°C] Hysteresis for thermal overload flag. The flag is dele- ted, as soon as the temperature falls below the thres- hold minus hysteresis. Commands for Audio Monitoring Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 157 Commands for Control Inputs / Control Outputs /CONTROL /IN1 ON, OFF State of the control input STATE /TIME R / W 0...10.0 [s] Delay / debounce time during activation Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 158 (same as above but for switching off a control output) /OUT2 (same as above but for the control output 2) /MEMFLAG /SET R / W NONE, List of currently set Memo flags 1...16 Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 159 ON, OFF Inverts the result of the programmed condition /PRM /... Parameters and values for functions mentioned above (same as above but for transmitting Job Codes 2 to 5) Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 160 (same as above, but for channel B) /MEAS Reading displays the actual output load A, B values including MIN and MAX values that occurred. Writing the channel names resets MIN and MAX values. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 161 NONE, Template for monitoring GLOBAL 0...255 status and error flags of external CAN devices. /GLOBAL NONE, List of external CAN devices with set 0...255 GLOBAL status and error flags. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 162 0 / 1 0 = ON, 1 = BYPASS eq type 0...5 0 = PEQ, 1 = LOSHELV, 2 = HISHELV, 3 = LOCUT, 4 = HICUT, 5 = ALLPASS Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 163 /PRM/IDX113 input A eq3 quality /PRM/IDX173 output B level /PRM/IDX114 input A eq4 bypass /PRM/IDX174 output B trim level /PRM/IDX115 input A eq4 type /PRM/IDX175 output B delay bypass Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 164 B eq3 bypass /PRM/IDX18E output B eq2 slope /PRM/IDX12F input B eq3 type /PRM/IDX18F output B eq2 frequ /PRM/IDX130 input B eq3 slope /PRM/IDX190 output B eq2 gain Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 165 A route /PRM/IDX149 output A compressor bypass /PRM/IDX14A output A compressor type (ratio) /PRM/IDX14B output A compressor threshold /PRM/IDX14C output A compressor attack /PRM/IDX14D output A compressor release Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 166 (ID) triggers the function with its specified parameter values. Available functions for /JOB/RXx/ FNCT/... and corresponding parameters /JOB/RXx/PRM/... are identical with local GPI functions, as outlined in the table. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 167 MEAS Initiates impedance testing at a fixed frequency ../PRM/ 10...20000 [Hz] Generator frequency for impedance test FREQU ../PRM/ -128...+50 [dBu] Generator level for impedance test in channel A GAIN_A Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 168 (up to 10 sec.). The INV parameter allows inverting the state of the assigned function. Available functions for /JOB/TXx/FNCT/... as well as corresponding parameters /JOB/TXx/PRM/ ... are identical to local GPO functions, as outlined in the table. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 169 GNDFLT_A, set, when ground fault has been detected GNDFLT_B ZMIN_A, set, when the measured output load is out of limit value range ZMIN_B, ZMAX_A, ZMAX_B Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 170 Using IRIS-Net, upgrading the firmware is possible via the CAN Remote Control Interface. In this way you can install new firmware and future software extensions to always keep your EV Remote Amplifier System up-to-date.
Page 171 Connect the desired remote amp(s) via CAN-bus to your PC. Start the IRIS-Net software and open your project. Your remote amps and the icon of a PC with CAN-label should appear on your screen. The PC-icon represents the CAN-interface of your PC or notebook.
Page 172 The IRIS-Net software package always includes the most up-to-date remote amplifier firmware version. The corresponding file is located in the directory: \IRIS-Net\Firmware\RCM-24. This path also appears in the line “Location”. If you want to install a different (preferably newer) firmware version, you have to copy the corresponding file into this directory first.
Page 173 The following example shows how to upgrade the firmware of the remote amps with the addresses 1 and 2 to firmware version V 1.18. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 174 However, the software does not wait for acknowledgements of the concerned amps any longer. – If the IRIS-Net-software recognizes an error or “Time Out” during upgrading, it automatically switches to “Single Step” mode, which offers the possibility to repeat the upgrade in single steps. If a “Time Out” message is displayed while upgrading is in progress, under no circumstance switch off any amps! –...
Page 175 Start Update - Pro- gram. – If the checksum evaluation shows errors, repeat the entire upgrade procedure. Don’t forget to uncheck “Single Step” mode, for the upgrade to run automatically. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 176: Rcm-26
Furthermore, the RCM-26 provides a control port with freely programmable control inputs and control outputs. Control inputs (GPI's) allow the connection of switches. IRIS-Net offers the possibility to program a variety of logic functions for the inputs (e.g. switching to an alarm-preset with maximum energy in the speech area). Control outputs (GPO's) allow the connection of external components, which, for example, are used to signal specific states to peripheral equipment.
Page 177 LC-display. By utilizing the optionally available remote control module that is compatible with IRIS-Net, this power amplifier additionally offers comprehensive remote monitoring and remote control functions plus a universal 2-channel digital audio controller (DSP) including highly precise FIR-filtering.
Page 178 The green ONLINE indicator shows that the corresponding amplifier is on-line and that sending and receiving data is possible. When on-line, any parameter changes are immediately transmitted and active. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 179 In case the amplifier needs to be switched off to prevent power amplifier and connected speaker systems from being damaged, this is indicated by the PROT and MUTE LEDs being lit simultaneously. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 180 Clicking this switch activates the STATUS indicator on the amplifier’s rear panel as well as in the amplifier’s front panel window in the IRIS-Net software. Normally, the STATUS indicator blinks only during serial communication. Once the STATUS switch is engaged, the STATUS indicator blinks in a steady but fast sequence.
Page 181 The DSP page provides an overview plus access to all DSP functions (Filter, Delay, X-Over, Limiters) of the amplifier. Speaker This page allows loading and displaying speaker data. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 182 Shows the uptime of the amplifier (standby not included) since the last reset of the Event Log. For further details about the amplifier’s Event Log please refer to the owner's manual. MAINS VOLTAGE Shows the mains voltage and the mains current consumption. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 183 Enable input to analog input automatically if the digital input signal is not HINT: The value of the property “Audio Input Switching. AES Fail. Enable” corresponds to this control. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 184 AES signal or input. This feature allows a redundant analog signal to be fed to the amplifier and automatically switch over to the “backup” signal without user intervention. Open the Modify Properties dialog from the context menu of the RCM-26 remote amplifier in the IRIS-Net worksheet. Following table lists the relevant properties for automatic audio input switching.
Page 185 Control Outputs: Internal status changes inside of the amplifier, such as operational faults, alerts when exceeding parameter limits, and internal operational statuses can be signaled to external systems or central control units. Example: Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 186 Programming job codes is nearly identical to the programming of control inputs and outputs. Receive Jobs: A receive job is a function that is carried out as soon as the corresponding function number (the Receive Job Code) is received. Example: Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 187 Range Description 1...65536 Here, you can specify which job code numbers an amplifier transmits on the occurrence of specific events. Entering random numbers between 0 and 65536 is possible. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 188 B, OUT A, OUT Memo flag Set, Clear, Sets, erases or changes selected memory flags. Up to 16 memory Toggle Memo flags are available and simultaneously accessible. flags 1 - 16 Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 189 The Flow Diagram Selector can be accessed from any DSP page offering navigation means within the DSP signal processing functions. The Flow Diagram Selector lets you select different function blocks, where the actually selected block is displayed in a yellow engaged field. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 190 The FLOW DIAGRAM window opens when clicking on the first, fourth or ninth block in the Flow Diagram Selector. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 191 A click with the right mouse button onto routing block opens the Copy & Paste menu of all DSP set- tings, which allows copying all DSP parameters of an amplifier to any other amplifier within the same project. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 192 Clicking with the right mouse button opens the Copy & Paste menu, which allows copying all parameters of the corresponding Limiters block to any other Limiters block within the same project. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 193 Store / Recall / Preview Element Description STORE saves all momentary set DSP parameters into the actually loaded preset. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 194 Enter the password into the text boxes and confirm the password by pressing the OK button. For editing protected Owner presets press the Unlock Owner Presets button and enter the password. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 195 Import / Export of Preset Files IRIS-Net allows the storing of all DSP parameters of an amplifier together with the according preset name in a file, and to load amplifier parameters from these files. Therefore, IRIS-Net creates a sub-directory \Presets during installation, where all factory-presets are saved in to.
Page 196 Element Description IRIS-Net allows importing loudspeaker presets that have been created in Electro-Voice RACE by clicking onto the button IMPORT RACE FILE to open the following dialog box. First, you have to select the desired RACE file by use of the Browse... button. Because a RACE file can hold the data of up to 31 EV Dx38, you need to continue by selecting the desired device from the RACE file within the dialog SELECT DEVICE FROM RACE FILE.
Page 197 A click with the right mouse button opens the “Copy & Paste” menu, which allows convenient copying all EQs of the corresponding input to any other EQ-filter bank within the same project. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 198 BYPASS switches the corresponding filter ON (not engaged) or OFF (engaged), which allows for quick A / B-evaluation of the actual effect that a filter has on the sound. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 199 A click with the right mouse button on this field opens the Copy & Paste menu, which allows copying all master delay parameters of the selected input to any other master delay within the same project. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 200 Except for the possibility to select All pass as filter type, these filters are identical to the ones of the master-EQ's. The Channel-EQ is selected by clicking on the fifth block of the flow diagram selector or by double clicking on the CHANNEL EQ block in the full-scale flow diagram. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 201 Lopass / Hipass creates low pass respectively high pass filters with adjustable frequency and slope. Allpass is a filter which only affects the phase but not the frequency response of the transmission function. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 202 For an improved overview the name of the corresponding filter band appears in color as soon as the mouse cursor is positioned over its white dot. An additional white graph indicates the frequency response of the actually selected filter. Bosch Security Systems B.V. User Manual...
Page 203 Switch for additionally indicating measured speaker transfer functions. For this function to be effective you first have to load speaker data in the Speaker register sheet. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 204 LO-PASS filter to any LO-PASS Bessel 12dB, filters within the same project. Butterworth 12dB, Linkwitz/Riley 12dB, Bes- sel 18dB, Butterworth 18dB, Bessel 24dB, Butterworth 24dB, Linkwitz/Riley 24dB FREQ: 20 Hz...20 kHz Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 205 A filter’s title lights in color as soon as the mouse cursor is positioned on top of the corresponding white dot to provide improved overview and handling. An extra white graph is displayed in addition, representing the frequency response of the corresponding selected filter. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 206 Switch for additionally indicating measured speaker transfer functions. For this function to be effective you first have to load speaker data in the Speaker register sheet. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 207 LO PASS sets the cut-off frequency of the Lo pass filter. Allows increasing the level of the corresponding channel by up to 6 dB or lowering it by up to 30 dB. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 208 Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 209 A click with the right mouse button on this field opens the Copy & Paste menu, which allows copying all limiters parameters of the corresponding channel to any other channels within the same project. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 210 (button is engaged). This allows quick A / B-comparison of the limited and non-limited audio signals. General Parameters Element Default Range Description dBu / Volts This lets you select the unit for the threshold parameter. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 211 ”speaker files” (*.spk), contain factory-measured frequency- and phase responses of all common Electro- Voice loudspeaker systems. Some examples are provided in the IRIS-Net directory Speaker Files. HINT: When importing a speaker setting into a output channel the corresponding speaker file is imported automatically.
Page 212 Switching the display of the corresponding speaker data for an amplifier channel on/off is performed using the ”Show Speaker A” and ”Show Speaker B” switches. Channel Parameters Element Default Range Description Channel description and channel name Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 213 Clicking the button LOAD SPEAKER FILE opens a dialog that allows the selection of the desired speaker file. Different loudspeaker files can be found in the Speaker files IRIS-Net folder. The name of the loaded loudspeaker model is shown in the black-shaded field on the right.
Page 214 The VOLTAGE display provides continuous indication of the corresponding power amp channel’s output voltage. The CURRENT display provides continuous indication of the corresponding power amp channel’s output current. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 215 The tolerance range is graphically displayed as spread in the corresponding color that surrounds the reference graph. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 216 The test generator allows outputting a selected test-tone at an adjustable level via the power amps channel A and/or channel B which allows testing the cable run from the amplifier output to the connected loudspeaker systems as well as testing the functionality of the loudspeaker components Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 217 COLLECTED ERROR STATE indicator resembles exactly the Amplifier State indicator of the System Check Window. The collected fault state message can be outputted via a control output. For detailed explanation please refer to chapter Config & Info. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 218 (please refer to the owner‘s manual for more details). In this case the THERMAL WARNING indicator lights red. With the THERMAL HEADROOM parameter in IRIS-Net the threshold for the THERMAL WARNING indication can be changed to get the warning indication already at lower temperatures, meaning before the amplifier reduces the output power.
Page 219 The RS-232 interface of the RCM-26 remote power amps is permanently configured allowing full duplex operation. Set values are: Parameter Setting Baud Rate 19200 bits per second Data Bits Parity None Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 220 CAN to remote RCM, write CAN address (1...250) of RCM to connect to, or write 0 to disconnect. Active remote connection is shown as address in brackets before the prompt. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 221 R / W 0...40 [°C] Hysteresis for thermal overload (OVT) flag. The flag is deleted, as soon as the temperature falls below the threshold minus hysteresis. Commands for Audio Monitoring Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 222 PASSW "password" next reset. Saving owner presets and password definition can only be done if this state is 'OK'. Read value (OK, FALSE) if the owner is identified successfully. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 223 For further details please refer to the VU, CTL_IN, table "Control Outputs - GPO Functions" ERR- FLAG, on this page. MEMFLAG, PRESET /INV R / W ON, OFF Inverts the result of the programmed condition Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 224 Number (ID) for job code to be transmitted. Each power amp can transmit up to 5 job codes. /TIME R / W 0...10.0 [s] Delay / debounce time for programmed condition Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 225 Flag template for Collected Error Flag (a COLLE list of status and error flags as mentioned above). The state is buffered (Hold function) when COLLECT is listed in the template. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 226 AES input. /AES /LOCK ON, OFF Read out actual lock stat of AES input Read out sample rate of AES input signal Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 227 0...2 0=0dB bypass, 1=6dB, 2=12dB /IDX11 eq3frequency 20...20000 /IDX12 eq3 gain -18...12 /IDX13 eq3 quality 0.4...40 /IDX14 eq4 bypass 0 / 1 0 = ON, 1 = BYPASS Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 228 0...3 0 = nothing, 1 = A, 2 = B, 3 = A+B /IDX03 level trim -30...+6 /IDX04 delay bypass 0 / 1 0 = ON, 1 = BYPASS Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 229 0 = peq, 1 = loshelv, 2 = hishelv, 3 = locut, 4 = hicut, 5 = allpass /IDX1B eq2 slope 0...2 0 = 0dB bypass, 1 = 6dB, 2 = 12dB /IDX1C eq2 frequency 20...20000 Hz /IDX1D eq2 gain -18...12 Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 230 0 = OFF, 1 = ON enable /IDX3A testgenerator level -128...+40 dB(u) at power amp output /IDX3B not used /IDX3C not used /IDX3D pilotgenerator 0 / 1 0 = off, 1 = on enable Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 231 The AES/EBU digital audio interface is in locked state (collect / GPO reads inverted) ERRDISP The LC-display indicates a error message AESERROR The AES/EBU digital audio interface is in erratic state VLT_WARN Mains voltage warning Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 232 The load is above maximum, open PILOT The 19 kHz pilot tone is not detected above threshold MEAS The sweep measurement is active THRM_HDRM The thermal headroom is below minimum Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 233 Toggles a DSP parameter between 0 and 1 (this only makes sense for flag parameters, e.g. MUTE, BYPASS, etc.) .../PRM/TYPE IN / OUT IN selects input channel, OUT selects output channel Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 234 TESTGEN Defines parameters for the audio testing generator ../PRM/ A / B / A,B Selects input channel A, or input channel B, or INPCHAN input channel A and B Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 235 IN selects input channel, OUT selects output channel ../PRM/CHAN A / B / Selects channel A, or channel B, or channel A and B ../PRM/IDX 00...FF Selects the DSP parameter via index number Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 236 Interpretation results in "true", when the actual preset is identical to a selected preset. ../PRM/DIRTY ON, OFF Selection is also valid, when parameters have been changed (dirty) ../PRM/USER NONE, List of selected user presets 1...6 Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 237 Connect the desired remote amp(s) via CAN-bus to your PC. Start the IRIS-Net software and open your project. Your remote amps and the icon of a PC with CAN-label should appear on your screen. The PC-icon represents the CAN-interface of your PC or notebook.
Page 238 Firmware update of the Remote Control Module The CAN-interface window provides a toolbar (top line). Clicking onto the U-icon (Update) opens a Module Selection dialog. Select RCM-26 and click onto "Continue". Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 239 The IRIS-Net software package always includes the most up-to-date remote amplifier firmware version. The corresponding file is located in the directory: \IRIS-Net\Firmware\RCM-26. This path also appears in the line “Location”. If you want to install a different (preferably newer) firmware version, you have to copy the corresponding file into this directory first.
Page 240 The actual firmware file including version number and date is indicated and can be selected in the line “Firmware”. The IRIS-Net software package always includes the most up-to-date remote amplifier firmware version. The corresponding file is located in the directory: \IRIS\Firmware\TG POWERH. This path also appears in the line “Location”.
Page 241 However, the software does not wait for acknowledgements of the concerned amps any longer. – If the IRIS-Net-software recognizes an error or “Time Out” during upgrading, it automatically switches to “Single Step” mode, which offers the possibility to repeat the upgrade in single steps. If a “Time Out” message is displayed while upgrading is in progress, under no circumstance switch off any amps! –...
Page 242 Start Update - Program. – If the checksum evaluation shows errors, repeat the entire upgrade procedure. Don’t forget to uncheck “Single Step” mode, for the upgrade to run automatically. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 243: Rcm-28
Additionally, the RCM-28 provides a control port with freely programmable control inputs and control outputs. Control inputs (GPIs) allow the connection of switches. IRIS-Net offers the possibility to program a variety of logic functions for the inputs (e.g. switching to an alarm-preset with maximum energy in the speech area). Control outputs (GPOs) allow the connection of external components, which, for example, are used to signal specific states to peripheral equipment.
Page 244 LC-display. By utilizing the optionally available remote control module that is compatible with IRIS-Net, this power amplifier additionally offers comprehensive remote monitoring and remote control functions plus a universal 2-channel digital audio controller (DSP) including highly precise FIR-filtering.
Page 245 CAUTION: Using * (asterisk) and/or = (equal) signs in a name is not permissible. The Online / Offline indicator signals whether the selected amplifier is currently communicating with IRIS-Net. The red OFFLINE indicator signals that the corresponding amplifier is off-line and that therefore no communication is possible.
Page 246 In case the amplifier needs to be switched off to prevent power amplifier and connected speaker systems from being damaged, this is indicated by the PROT and MUTE LEDs being lit simultaneously. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 247 AMP ROUTING shows how the audio inputs handle the input signals. Possible settings are DUAL and PARALLEL. Switching the amp routing is only possible locally at the power amplifiers, details can be found in the amplifiers owner's manual. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 248 Clicking this switch activates the LOCK indicator on the amplifier’s rear panel and all amplifier front panel LEDs, as well as in the amplifier’s front panel window in the IRIS-Net software. This function is meant for identifying or searching an amplifier in a large system setup.
Page 249 Shows how the amplifier's audio inputs handle the input signals. Possible amp routings are DUAL and PARALLEL. GROUND LIFT Shows the setting of the amplifier's GROUND LIFT switch. Possible settings are GROUNDED and UNGROUNDED. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 250 (Analog) or the digital audio input (AES/EBU) are available. Select Auto to output the digital audio signal and switch from digital input to analog input automatically if the digital input signal is not OK. Digital Input Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 251 AES signal or input. This feature allows a redundant analog signal to be fed to the amplifier and automatically switch over to the „backup“ signal without user intervention. Open the Modify Properties dialog from the context menu of the RCM-28 remote amplifier in the IRIS-Net worksheet. Following table lists the relevant properties for automatic audio input switching.
Page 252 Function menu opens a dialog field that shows all accessible functions. The table "Input and Receive Job Functions" lists all functions together with their individual settings. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 253 (empty) (empty) / X This column allows entering whether a status is signaled when the specified Condition is „true“ (no entry) or „false“ (click „X“ to signal an inverted state). Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 254 Here you can set the different function parameters. For more information, please refer to the table "Input and Receive Job Functions". Opt. Value (empty) Certain functions allow specifying optional parameter values. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 255 Input and Receive Job Functions: The following table lists all functions together with their individual settings, which can be triggered via control input or Receive Job. Function Parameter Opt. Value Function executed Empty None Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 256 DSP parameters Corresponding Set parameter value reached or exceeded Set Parameter Value parameter value declined (parameter- dependent) Temp Temperature in °C Set temperature reached or exceeded Set temperature declined Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 257 Frequency crossover-filters as well as the parameters trim, polarity and delay for both channels are located in the Output X-Over area. SPEAKER This page provides a FIR-Filter for each amplifier channel. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 258 Clicking with the right mouse button opens the Copy & Paste menu, which allows copying all parameters of the corresponding Delay block to any other Input Delay block within the same project. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 259 Clicking with the right mouse button opens the Copy & Paste menu, which allows copying all parameters of the corresponding FIR Filter block to any other FIR Filter block within the same project. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 260 The EDITED indicator provides information whether a parameter has been altered since the last RECALL. If the indicator lights green, parameters have been edited and therefore differ from the ones of the preset that is shown. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 261 User presets” dialog, where the password can be entered. Press the Set Password button to activate the protection. Enter the password and press the Unlock User presets button to deactivate the password protection. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 262 Import / Export of Preset Files IRIS-Net allows the storing of all DSP parameters of an amplifier together with the according preset name in a file, and to load amplifier parameters from these files. Therefore, IRIS-Net creates a sub-directory \RCM-28 Presets during installation, where all factory-presets are saved in to.
Page 263 Hi, Lo and All pass filters with slopes of 12dB/oct.. 0 dB -18 to +12 dB GAIN defines the amplification (increase) or attenuation (reduction) of parametric EQs or low shelving and high shelving equalizers. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 264 A click with the right mouse button opens the ”Copy & Paste” menu, which allows convenient copying all delay parameters of the corresponding input to any other delay within the same project. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 265 Array Parametric EQ (input PEQ), which always provides precise overview and control of the resulting frequency response at this point. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 266 6dB/Oct, 12dB/ SLOPE sets the steepness or filter-order of low or high shelving equalizers and low or high pass filters. Setting different slopes within the transmission range is possible. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 267 Additionally, the array delay provides a convenient section to apply dedicated delay to individual subwoofer cabinets to create gradient or beam-formed arrays. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 268 A delay’s title is shown black as soon as the mouse cursor is positioned on top of the corresponding icon to provide improved overview and handling. Bosch Security Systems B.V. User Manual...
Page 269 Switch for additionally indicating measured speaker transfer functions. For this function to be effective you first have to load speaker data in the ”Speaker” tab. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 270 ORDER (only available with All pass filters) sets the desired filter order of an All pass filter. A 1st order All pass filter rotates the phase by 180°, a 2nd order All pass filter rotates the phase by 360°. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 271 Displays the resulting transfer function of all filter and level trim settings and therefore graphically displaying the audible result at the amplifier‘s outputs. The audible result is displayed in bright colors while all ”electrical” graphs are drawn in dark colors. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 272 HI-PASS filter to any HI- 12dB, Linkwitz/Riley 12dB, PASS filters within the same project. Bessel 18dB, Butterworth 18dB, Bessel 24dB, Butterworth 24dB, Linkwitz/ Riley 24dB FREQ: 20 Hz to 20 kHz Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 273 A filter’s title ”lights” in color as soon as the mouse cursor is positioned on top of the corresponding white dot to provide improved overview and handling. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 274 A click with the right mouse button opens the ”Copy & Paste” menu, which allows convenient copying of all FIR filter settings of the corresponding output to any other FIR filter within the same project. Bosch Security Systems B.V. User Manual...
Page 275 Clicking the MUTE button once again with the left mouse button disables the mute-function and the output is again active. The MUTE button is virtually disengaged and not lit. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 276 PA to the stage or aligning the full-range loudspeakers to the subwoofers. The Output Delay parameter determines the delay time of the corresponding channel or the distance between different loudspeaker clusters. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 277 A delay’s title is shown black as soon as the mouse cursor is positioned on top of the corresponding icon to provide improved overview and handling. Bosch Security Systems B.V. User Manual...
Page 278 Speaker settings include factory-defined time constants, so this section is only for use when creating DSP settings from scratch. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 279 A click with the left mouse button onto this dot and keeping the mouse button pressed down lets you set the threshold for the corresponding limiter by vertically dragging the mouse. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 280 ”speaker files” (*.spk), contain factory-measured frequency- and phase responses of all common Electro- Voice or DY- NACORD loudspeaker systems. Some examples are provided in the IRIS-Net directory Speaker Files. HINT: When importing a speaker setting into a output channel the corresponding speaker file is imported automatically.
Page 281 HINT: The speaker impedance test is optimized for low impedance. Graphic Display Indication Element Default Range Description The switches "Show Loadplot A" and "Show Loadplot B" turn the indication of the corresponding impedance graphs ON or OFF. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 282 -10 / 0 / GEN. LEVEL sets the generator level for speaker impedance testing. 10 dBu CAUTION: Extremely high levels during measurement may result in seriously damaging connected components. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 283 A click on the Supervision & Test tab selects the page while in the Setup & Control Window. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 284 A green STATE indicator signals normal operation. A red STATE indicator signals error detection. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 285 (please refer to the owner‘s manual for more details). In this case the THERMAL WARNING indicator lights red. With the THERMAL HEADROOM parameter in IRIS-Net the threshold for the THERMAL WARNING indication can be changed to get the warning indication already at lower temperatures, meaning before the amplifier reduces the output power.
Page 286 Select the OMNEO device that is the signal source of the audio signal to be used in the RCM-28. Different OMNEO devices can be selected for INPUT CHANNEL A or B. CHANNEL Select the OMNEO channel to be used in the INPUT CHANNEL A or B. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 287 Firmware upgrade The RCM-28 FWUT FirmWare Update Tool is available in the download sections of www.dynacord.com or www.electro- voice.com Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 288: Rcm-810
Furthermore, the RCM-810 provides a control port with freely programmable control inputs and control outputs. Control inputs (GPI's) allow the connection of switches. IRIS-Net offers the possibility to program a variety of logic functions for the inputs. Control outputs (GPO's) allow the connection of external components, which, for example, are used to signal specific states to peripheral equipment.
Page 289 Keep the mouse button pressed while dragging the panel. Indications and Functions of the Amplifier Control Panel Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 290 Press Return on the keyboard to acknowledge your entry. HINT: Entering channel names is also possible within the Setup & Control Panel on the Config & Info page. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 291 Clicking on the VLD SET button of a 4 or 8 channel amplifier opens the VLD tab in the Setup & Control window. The LED indicator next to the button lights when VLD of the channel is activated. Bosch Security Systems B.V. User Manual...
Page 292 Clicking this switch activates the STATUS indicator on the amplifier’s rear panel as well as in the amplifier’s front panel window in the IRIS-Net software. Normally, the STATUS indicator blinks only during serial communication. Once the STATUS switch is engaged, the STATUS indicator blinks in a steady but fast sequence.
Page 293 (closed). HINT: When a control output has already been programmed, the programmed function defines the state of the control output and manual control is not possible. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 294 0...10027 ms Here you can program delay or debouncing times. Following a status 16.33 ms change the assigned function is initiated after the set time interval has Steps past. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 295 Each amplifier is capable of transmitting and receiving up to 5 different job codes. Programming job codes is nearly identical to the programming of control inputs and outputs. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 296 Transmit Job Nr. 3: GPI IN2 (Job Code 3 is transmitted when control input 2 is closing) – Transmit Job Nr. 4: Invert GPI IN2 (Job Code 4 is transmitted when control input 2 opens) Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 297 Output and Transmit Job Conditions: The following table lists all amplifier statuses that can be used for triggering control outputs or for sending Transmit Job Codes. Function Parameter Opt.Value Invert Triggering Event / Status Change Empty Not configured Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 298 COLLECTED ERROR STATE indicator resembles exactly the Amplifier State indicator of the System Check Window. The collected fault state message can be outputted via a control output. For detailed explanation please refer to chapter Config & Info. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 299 When the red PROTECT MUTE indicator lights, the signal path gets switched off. The amplifier needs to be switched off to prevent power amplifier and connected speaker systems from being damaged, this is indicated by the PROTECT and MUTE-LEDs being lit simultaneously. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 300 Additionally a 50 Hz Low Cut Filter can be activated for each channel. To select the page click onto the VLD register in the Setup & Control Window. Bosch Security Systems B.V. User Manual...
Page 301 Using IRIS-Net, upgrading the firmware is possible via the CAN Remote Control Interface. In this way you can install new firmware and future software extensions to always keep your Remote Amplifier System up-to-date.
Page 302 Connect the desired remote amp(s) via CAN-bus to your PC. Start the IRIS-Net software and open your project. Your remote amps and the icon of a PC with CAN-label should appear on your screen. The PC-icon represents the CAN-interface of your PC or notebook.
Page 303 The IRIS-Net software package always includes the most up-to-date remote amplifier firmware version. The corresponding file is located in the directory: \IRIS-Net\Firmware\RCM-810. This path also appears in the line “Location”. If you want to install a different (preferably newer) firmware version, you have to copy the corresponding file into this directory first.
Page 304 The actual firmware file including version number and date is indicated and can be selected in the line “Firmware”. The IRIS-Net software package always includes the most up-to-date remote amplifier firmware version. The corresponding file is located in the directory: \IRIS\Firmware\CPS DSA. This path also appears in the line “Location”.
Page 305 However, the software does not wait for acknowledgements of the concerned amps any longer. – If the IRIS-Net-software recognizes an error or “Time Out” during upgrading, it automatically switches to “Single Step” mode, which offers the possibility to repeat the upgrade in single steps. If a “Time Out” message is displayed while upgrading is in progress, under no circumstance switch off any amps! –...
Page 306 Start Update - Program. – If the checksum evaluation shows errors, repeat the entire upgrade procedure. Don’t forget to uncheck “Single Step” mode, for the upgrade to run automatically. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 307: Rev Wireless Microphone System
– "Smart" battery feature in the 9V transmitters means there is no wrong orientation – Interchangeable heads on the handheld transmitters – Cast magnesium case on the bodypack transmitter Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 308: Rev Device
Configuration menu or from the contextual menu within the IRIS-Net worksheet. To add devices to an IRIS-Net project, first select the desired device REVS or REVD in the Object Bar (or from the Devices window) and then drag and drop it into the worksheet. A dialog box opens, which lets you specify device- related settings such as amount of desired devices, address range, and interfaces.
Page 309 The edition of REV properties can be locked or unlocked. Pressing on the lock bitmap on the panel locks the edition. Pressing on lock again unlocks it. HINT: Locking or unlocking can be done only when no operation is performed currently on the receiver. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 310: Setup & Control
The CAN address of the left receiver (REV-D only) is always odd, the CAN address of the right receiver (both REV-S and REV-D) is always one higher than the left address and hence it is always even. In the IRIS-Net worksheet only the even CAN address is displayed on the receiver icon.
Page 311 Select the left or the right receiver. Right Rcvr HINT: The receiver selection option is disabled in a REVS receiver. Scan All Scan all o f the groups (factory and user) Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 312 Analyze operation. As this is a continuous operation it will continue until it is manually stopped. Click Stop to stop the operation. Sample Step and Dwell Time values can be modified from the list of values displayed in their respective combo-boxes. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 313 Set the sample step width in kHz. (kHz) Dwell Time Set the dwell time in seconds. (sec) Start Start the scan of the selected receiver Stop Stop the scan of the selected receiver. Misc Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 314 Allows adjusting the signal level at the XLR output. HINT: XLR Level is editable only if the Audio Out is selected as ‘Line’. Hi Z Level Allows adjusting the signal level at the Hi Z output. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 315: Digital Matrix
By using CobraNet or Dante redundant networks can be assembled. N8000 Device Start by creating an N8000 Device in your IRIS-Net project. Drag an N8000 from the Object Bar’s Devices category or from the Devices window into the worksheet (see also chapters: Devices and Configurations menu). The following dialog box appears: Enter the required number of devices and select a communication interface.
Page 316 Additional configuration windows can be navigated to by clicking on the icons at the top of the window. However, as a basic rule, IRIS-Net will remember which window was used last and reopen to this window next time you double click on the N8000 device icon.
Page 317 IRIS-Net internal device name of the N8000. IRIS-Net project filename. INFO This button displays information concerning the IRIS-Net project file. Date and time of the N8000 system clock. This button opens the system clock settings dialog box. SYNC This button syncs the N8000 system clock to the PC system clock.
Page 318 This indicates the DSP system’s estimated load. Adding supplementary DSP-Blocks is not possible when the actual load (DSP LOAD or DSP RAM) reaches 100%. Adding supplementary Delay-Blocks is not possible when the actual load (DELAY MEM) reaches 100%. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 319 There are several ways to restrict the rights for editing the DSP configuration of a N8000. Generally, editing the DSP configuration is only possible when logged-in in IRIS-Net as administrator. Therefore, it is advisable to create additional user accounts in an IRIS-Net project, besides the administrator account, and to assign appropriate passwords. Please also refer to the corresponding chapter "Password Protection of a Project"...
Page 320 An existing preset can be converted into a scene. A scene contains a defined subset of the preset parameters. Select the preset to be converted from the Preset List and press the SCENE button. The following dialog box appears: Bosch Security Systems B.V. User Manual...
Page 321 Select "Create Super Block" from the contextual menu. The Super Block dialog appears. Enter the desired name for the Super Block in the "Enter Super Block Name" dialog and click on OK. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 322 IRIS-Net DIGITAL MATRIX | en The Super Block appears in the list of superblocks. It is stored in the IRIS-Net installation directory in the subdirectory "superblocks". Use of a Super Block Please proceed as follows to add a Super Block to the DSP configuration: Open the category PROCESSING OBJECTS utilities of the N8000/P 64 or the category Advanced of the DPM 8016.
Page 323 The DSP blocks CobraNet Inputs provide the possibility to select a bundle to be received while the DSP blocks CobraNet Outputs allow configuring one bundle each for sending, including its contained channels. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 324 RECEIVE An error has been detected during data reception via CobraNet. TRANSMIT An error has been detected during data transmission via CobraNet. GENERAL System fault within the CM-1 module. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 325 Dante Inputs and Dante Outputs (see DANTE INPUTS, page 386) provide the possibility to select and configure Dante channels. HINT: The Dante Configuration dialog (menu Tools > Dante Configuration) provides the possibility to configure the Dante network. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 326 This window provides detailed information about an OM-1 OMNEO Interface module installed in the N8000. The DSP blocks OMNEO Inputs and OMNEO Outputs (see DANTE INPUTS, page 386) provide the possibility to select and configure OMNEO or Dante channels. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 327 Dante network. Left clicking the node in the matrix where the transmitter channel’s column and the receiver channel’s line meet with the mouse does connect an output to an input. Again clicking onto the corresponding node disconnects inputs and outputs. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 328 CAN BUS, RS-232 and N8000 CONTROL PORT settings can be made in here. Configuring the Ethernet interface is done under Network Settings in the General window. Additionally, Ethernet settings are also accessible from the Matrix > Configuration via USB menu within IRIS-Net. Element Description Bosch Security Systems B.V.
Page 329 Clicking with the right mouse button on the corresponding symbol of a control input provides opens the configuration dialog of this control input. (not yet activated) Displays the control inputs’ current condition. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 330 The Watchdog of the N8000 was activated. Press the CLEAR button to clear this error indication. BOOT COUNT Indicates the number of resets caused by the watchdog. Press the RESET button to reset the number to 0. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 331 (PLT) separately be configured in the input blocks. COLLECTED ERROR The FAULT-LED on the front panel of the N8000 lights at the occurrence of this STATE type of error. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 332 The RCM configuration does not represent the RCMs that are actually connected. REMOTE AMPLIFIER FAULT Collected Error for at least one RCM has been set. FAN SPEED Speed Description Slow High Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 333 In the Task Engine, different colors are used to distinguish the two types of variables. Analog blocks have blue connection nodes and blue wiring connection lines. Logic blocks have green connection nodes and green wiring connection lines. Connecting analog nodes to logic nodes is not allowed. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 334 Description The rational number at the output of the Addition block is always the sum of rational numbers of the (wired) inputs. Not all inputs have to be wired. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 335 The Boolean value at the output of the AND block is only true when all (wired) inputs are true. The Boolean value at the output of the OR block is only true when at least one (wired) input is true. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 336 (i.e. one input is true while the other input is false). Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 337 The Timer block sets the Boolean value „State“ at the output to true for the time „Duration“, if the Boolean value at the input changes from false to true. Following charts illustrate the functionality of the available block parameters: Retrigger Falling: Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 338 Edit Textbox dialog. This dialog allows editing the caption and e.g. font size and font type. Superblocks Superblocks are listed here. Please refer to page 240 how to use Superblocks. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 339: P 64 Digital Matrix
P 64 Device Start by creating an P 64 Device in your IRIS-Net project. Drag an P 64 from the Object Bar’s Devices category or from the Devices window into the worksheet (see also chapters: Devices and Configurations menu). The following dialog box appears: Bosch Security Systems B.V.
Page 340 Additional configuration windows can be navigated to by clicking on the icons at the top of the window. However, as a basic rule, IRIS-Net will remember which window was used last and reopen to this window next time you double click on the P 64 device icon.
Page 341 Indicates the MAC address of the connected P 64 when on-line. The MAC address of the P 64 is also shown on a label on the unit’s rear panel. IRIS-Net internal device name of the P 64. IRIS-Net project filename. INFO This button displays information concerning the IRIS-Net project file.
Page 342 There are several ways to restrict the rights for editing the DSP configuration of a P 64. Generally, editing the DSP configuration is only possible when logged-in in IRIS-Net as administrator. Therefore, it is advisable to create additional user accounts in an IRIS-Net project, besides the administrator account, and to assign appropriate passwords. Please also refer to the corresponding chapter "Password Protection Of A Project"...
Page 343 Presets have no influence on the DSP configuration itself - amount, type and wiring of DSP-Blocks. Element Description List of all P 64 presets. Selecting a preset with the left mouse button shows a description of the correspondent preset in the Preset Description window. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 344 An existing preset can be converted into a scene. A scene contains a defined subset of the preset parameters. Select the preset to be converted from the Preset List and press the SCENE button. The following dialog box appears: Bosch Security Systems B.V. User Manual...
Page 345 Select "Create Super Block" from the contextual menu. The Super Block dialog appears. Enter the desired name for the Super Block in the "Enter Super Block Name" dialog and click on OK. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 346 IRIS-Net DIGITAL MATRIX | en The Super Block appears in the list of superblocks. It is stored in the IRIS-Net installation directory in the subdirectory "superblocks". Use of a Super Block Please proceed as follows to add a Super Block to the DSP configuration: Open the category PROCESSING OBJECTS utilities of the N8000/P 64 or the category Advanced of the DPM 8016.
Page 347 The DSP blocks CobraNet Inputs provide the possibility to select a bundle to be received while the DSP blocks CobraNet Outputs allow configuring one bundle each for sending, including its contained channels. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 348 Synchronizing the DSP system to CobraNet is not possible. WATCHDOG The CM-1 is being reset because of a hardware or software failure. INTERFACE An error has been detected in the communication with the CM-1 interface. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 349 Dante Inputs and Dante Outputs (see DANTE INPUTS, page 386) provide the possibility to select and configure Dante channels. HINT: The DanteConfiguration dialog (menu Tools > DanteConfiguration) provides the possibility to configure the Dante network. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 350 OMNEO Inputs and OMNEO Outputs (see DANTE INPUTS, page 386) provide the possibility to select and configure OMNEO or Dante channels. HINT: The Dante Configuration dialog (menu Tools > Dante Configuration) provides the possibility to configure the Dante network. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 351 Dante networks are subject to a restriction. Only one transmitter channel can be connected to a receiver channel at a time (mixing signals is not possible). However, connecting a transmitter channel to various receiver channels is possible. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 352 BUS, RS-232 and P 64 CONTROL PORT settings can be made in here. Configuring the Ethernet interface is done under Network Settings in the General window. Additionally, Ethernet settings are also accessible from the Matrix > Configuration via USB menu within IRIS-Net. Bosch Security Systems B.V.
Page 353 Displays the current CAN-Bus status. Possible indications are: BUS OK, Bus Heavy, and Bus Off. USED BANDWIDTH Displays the used bandwidth of the CAN-Bus. CAN ERRORS Number of errors on the CAN-Bus that have been detected during send (TX) or reception (RX). Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 354 Further details can be set and are being displayed in the corresponding Config and Info dialogs. Element Description The current condition of each type of error gets indicated. Green means no error, red indicates that an error has been detected. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 355 The DYNACORD DPM 4000 that is connected via RS-232 port cannot be reached anymore. RS-232 PORTS Malfunction has been detected for an external device, which is being monitored via RS-232 port. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 356 The RCM configuration does not represent the RCMs that are actually connected. REMOTE AMPLIFIER FAULT Collected Error for at least one RCM has been set. FAN SPEED Speed Description Slow Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 357 The Virtual Analog block has the same behaviour as the IO Analog block, but has no connection property. Instead the rational number assigned to the ‚Value‘ property of the block will be sent to the output. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 358 The Not Equal block compares the rational numbers at the inputs. The Boolean value at the output is only true when the numbers that are present at the inputs differ from each other. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 359 The User Fault block is used for indicating a Boolean value by a User Fault. The User Fault is active when the input is true. The output always presents the state of the User Fault. Bosch Security Systems B.V. User Manual...
Page 360 The Not Equal block compares the Boolean values at the inputs. The Boolean value at the output is only true when the values at the inputs are different from each other (i.e. one input is true while the other input is false). Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 361 The Timer block sets the Boolean value „State“ at the output to true for the time „Duration“, if the Boolean value at the input changes from false to true. Following charts illustrate the functionality of the available block parameters: RetriggerFalling: Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 362 Edit Textbox dialog. This dialog allows editing the caption and e.g. font size and font type. Superbloc Superblocks are listed here. Please refer to page 240 how to use Superblocks. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 363 Stereo Crossover Delay Mono Delay x Delay blocks in Mono/Stereo with 10, 100, 500 or 2000 ms maximum delay. Entering values for distance and ambient temperature is possible. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 364 Expander Expander block with adjustable threshold, attack and release times, ratio and output level. Gate Gate block with adjustable threshold, attack, hold and release times and out- put level. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 365 FIR Controller blocks in Mono/Stereo with 1 to 5 ways. Controllers FIR Controller Each way has a 6- Band PEQ, a crossover with polarity, alignment delay, FIR filter, level control and a compressor/ Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 366 The Dante Output (DM-1) has 8 output channels. OMNEO Input The OMNEO input (OM-1) has 8 input channels. OMNEO Output - The OMNEO output (OM-1) has 8 output channels. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 367 Mute, Invert and Freeze Gain button. HINT: For using the automixer block with 16 or 24 inputs a DSP-2DSP Extension Module is required. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 368 THRESHOLD. 0.5 s 0.3... 20 s GAIN INCREASE defines the time interval that it takes the AGC to raise the signal level to the TARGET. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 369 However, All-Pass filters have frequency-dependent phase shifting (non-linear phase response), which is used for signal delay or phase equalization. Element Default Range Description Switch for selecting amplitude frequency response (magnitude) or phase response (phase) indication in the bode plot. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 370 Ambient noise can be picked up with up to 4 calibrated standard microphones. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 371 This meter indicates the current degree of amplification/ attenuation applied to program signals. -35 dBu -35...21 THRESHOLD defines the ambient noise level above which the program signal level is amplified. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 372 Each input channel has pilot tone detection, which, when activated, offers permanent monitoring of the output and the connecting audio cable of an external audio device. Activating and configuring pilot tone detection is possible in off-line mode from the Advanced Control window. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 373 Click with the right mouse button on the DSP block and select Advanced Control from the pop-up context menu of the Analog Line Input block to open the Advanced Control window. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 374 Without a pilot tone being present or if the signal level is below the set threshold, analysis results in a fault message on the corresponding input channel (red PLT button). HINT: Thresh (dBu) can only be configured OFFLINE. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 375 The fader display shows the numerical value of the current fader 8.0 dB setting and additionally provides the possibility for entering a desired value. Indicates a channel’s current output level. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 376 The checkbox activates the channel’s pilot tone generator. HINT: Gen. Used can only be configured OFFLINE. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 377 HINT: Freq (Hz) can only be configured OFFLINE. AUTO MIXER IRIS-Net provides Auto mixers with 2, 4, 6, 8, 10, 12, 16 or 24 inputs. For the 16 or 24 input Auto mixers a DSP-2 DSP extension card is required.
Page 378 SOLO button for monitoring a single input signal. PRIO button for increasing priority (= higher level) of input signal. Text field for labeling an input channel with an internal IRIS-Net name. CAUTION: The use of*(asterisk) and = (equal) in names is not permissible.
Page 379 50 dB (± 25 dB). 1000Hz FREQUENCY sets the center frequency of the band- Hz...20 pass filter. 0.4...1 The Q-value sets the quality and thus the response of the band-pass filter. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 380 – Multicast Bundle: a Multicast Bundle (bundle numbers 1 - 255) is not dedicated for one specific address. It is distributed throughout the entire network. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 381 16, 20 and 24 Bit. The channels of a bundle can have different bit rates. The MUTE button allows muting the corresponding channel. Text field for assigning an exclusive IRIS-Net name to the corresponding channel. CAUTION: Using * (asterisk) or = (equal) within a name is not permissible.
Page 382 The MUTE button allows muting the corresponding channel. Text field for giving a channel an internal IRIS-Net name. CAUTION: The use of * (asterisk) and = (equal) in names is not permissible. Bosch Security Systems B.V.
Page 383 This switch lets you toggle between amplitude frequency response (Magnitude) and phase response (Phase) indication. This switch allows selecting an amplification axis scaling of 25 dB (± 12.5 dB) or of 50 dB (± 25 Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 384 The LINK-Button allows linking (grouping) adjacent frequency bands (crossover ways). A frequency band’s LOPASS settings are automatically adopted to become the HIPASS settings of the adjacent band, and vice versa. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 385 The name of the respective filter is displayed in color when placing the mouse cursor over a spot. Bosch Security Systems B.V. User Manual...
Page 386 Text field for assigning the Dante Channel Name to the corresponding channel. The name is also used in the Dante Controller. CAUTION: Using * (asterisk) or = (equal) within a name is not permissible. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 387 CAUTION: The use of * (asterisk) and = (equal) in names is not permissible. OMNEO INPUTS The OMNEO Inputs DSP block is part of the OM-1 OMNEO module. The dialog provides 8 input channels from an OMNEO or Dante network. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 388 CAUTION: The use of * (asterisk) or = (equal) in names is not permissible. OMNEO OUTPUTS The OMNEO Output DSP block is part of the OM-1 OMNEO module. The dialog provides 8 output channels. The signal status of each channel is indicated. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 389 Delay blocks in monaural quality (1 input and 1 output) and stereo quality (2 inputs and 2 outputs) are available. Both types allow for delay times of 10, 100, 500 or maximally 2000 ms. Bosch Security Systems B.V. User Manual...
Page 390 A / B comparison of the effect that set parameters have on the sound characteristics. DEFAULT resets the temperature to 20° C or 68° F respectively. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 391 S/P DIF compatible audio signals. Switching between the two formats has to be performed manually, using the appropriate labeled buttons. When using the optical input, select OPTICAL as the signal type. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 392 Click with the right mouse button on the DSP block and select Advanced Control from the pop-up context menu of the Digital Input block to open the Advanced Control window. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 393 CHANNEL MODE Indicates the Channel mode (in Professional indicated, 2 mode only). channel, 1 channel, primary/ secondary, stereo, reserved for user applications, SCDSR, SCDSR (stereo left), SCDSR (stereo right), Multichannel Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 394 LINK button. This allows for the convenient synchronous setting of several output channels, e.g. for stereo signals. Element Default Range Description Permanent channel labeling. Channels are numbered from LINE 1 to LINE 8. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 395 Click with the right mouse button on the DSP block and select Advanced Control from the appearing contextual menu of the Digital Output block to open the Advanced Control window. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 396 This indicator signals in dB by how much the ducker reduces the signal level. A red bar that increases from the right to the left indicates the degree of gain reduction. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 397 The fader display shows the numerical value of the current fader setting and additionally provides the possibility for entering a desired value. MUTE button for muting the MIC or LINE signal. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 398 A short attack time means that even short signal dips below THRES- HOLD are efficiently expanded. Longer attack times leave signal dips below THRESHOLD untouched. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 399 The fader display shows the numerical value of the current fader setting and additionally provides the possibility for entering a desired value. FIR FILTER IRIS-Net provides FIR Filter blocks (Finite Impulse Response) of order 256 up to order 1792. Channel Parameters Element Description...
Page 400 HI PASS sets the cut-off frequency of the Hi pass filter. LO PASS sets the cut-off frequency of the Lo pass filter. FIR Filter Design Element Default Range Description ORDER of the FIR filter. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 401 The complete parameter set for a single loudspeaker is stored in the Speaker Setting file. IRIS-Net is shipped with a range of Speaker Setting files that hold parameter sets which have been optimized for Electro-Voice and DYNACORD loudspeaker systems. An overview of the...
Page 402 This block represents the 6 Channel EQs of the FIR/FIR-Drive controller. The graph shows the frequency response of the Channel EQ Block. Clicking on this block opens the CHANNEL EQ page. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 403 The parametric 6-Band equalizer is used for loudspeaker equalization. Select the Channel EQ by clicking onto the second block in the Flow Diagram Selector or by double clicking on the CHANNEL EQ block in the large Signal flow Diagram. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 404 For this function to be effective you first have to load speaker data in the Speaker register sheet. Filter Parameter Element Default Range Description Name of the corresponding filter band. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 405 Moving the mouse up or down lets you set the filters gain (depending on the type of filter). Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 406 The Separate switch allows indicating the individual transmission function of the controller ways. The Sum switch allows indication of the summed signal of all ways. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 407 12dB/Q=1.0, 12dB/ Q=1.2, 12dB/Q=1.5, 12dB/ Q=2.0, Bessel 12dB, Butterworth 12dB, Linkwitz/Riley 12dB, Bes- sel 18dB, Butterworth 18dB, Bessel 24dB, Butterworth 24dB, Linkwitz/Riley 24dB FREQ: 20 Hz...20 kHz Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 408 (engaged) the corresponding delay. The arrow sign next to SPEAKER opens a dialog for selecting speaker files. The text field shows the name of the currently loaded speaker file. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 409 Allows entering the ambient temperature. The -4...140 °F temperature entered is taken into account by the calculations IRIS-Net uses when changing between different distance type delay units. Temperatures can be entered in °C or °F. Editing X-Over filters via Mouse Dragging in the Graphic Display If a X-Over filter has been activated (filter type not set to OFF), a white dot in the frequency response graph represents the filters cut-off frequency.
Page 410 The fader display shows the numerical value of the current fader setting and additionally provides the possibility for entering a desired value. MUTE button for muting the output signal. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 411 Click on the fifth block in the Flow Diagram Selector or double click on the DYNAMICS block in the large Flow Diagram to select the Dynamics window. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 412 Limiter Parameters Element Default Range Description 21 dBu -9.0...+21. THRESHOLD defines the signal level at which the PA 0 dBu limiter sets in. 0.275... 8.696 V Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 413 Click on the fifth block in the Flow Diagram Selector or double click on the LIMITERS block in the large Flow Diagram to select the Limiters window. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 414 Calculator (Tools > Limiter Threshold Calculator) to calculate the corresponding voltage at the amplifier output. The Speaker Settings for DYNACORD or Electro-Voice speakers already include the correct setting for this parameter. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 415 Click onto one the dot with the left mouse button and keep it pressed down to set the threshold value of the compressor by dragging the mouse up or down. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 416 250 ms 10...1000 ms RELEASE defines the time that it takes to mute the signal after the HOLD period has passed. BYPASS activates (not engaged) or deactivates (engaged) the gate. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 417 The fader display shows the numerical value of the current fader setting and also provides the possibility for entering a desired value. GRAPHIC EQUALIZER IRIS-Net provides 10, 15 and 31 band graphic equalizers in monaural and stereo quality. Element Default Range...
Page 418 Lopass / Hipass creates low pass respectively high pass filters with adjustable frequency and slope. All pass is a filter which only affects the phase but not the frequency response of the transmission function. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 419 Bessel and Butterworth types, and to -6 dB in the Linkwitz-Riley types. The cutoff frequency is continuously variable from 10 Hz to 20 kHz. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 420 Clicking with the right mouse button on the white dot and keeping the mouse button pressed down allows changing the Q-values (if SLOPE is set to 12dB) of the filter. Bosch Security Systems B.V. User Manual...
Page 421 A white dot in the frequency response display represents an active filter (BYPASS not engaged). Clicking with the left mouse button on this dot and keeping the mouse button pressed down allows changing the filter’s frequency by moving the mouse to the left or to the right. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 422 HIGH-MID HIGH The complete parameter set for a single loudspeaker is stored in the Speaker Setting file. IRIS-Net is shipped with a range of Speaker Setting files that hold parameter sets which have been optimized for Electro-Voice and DYNACORD loudspeaker systems.
Page 423 This block represents the dynamics functions of the corresponding way. Two LEDs indicate whether compressors or limiters are activated. The graph indicates set values. Simply clicking onto this block branches to the DYNAMICS page. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 424 Switch for selecting amplitude frequency response (magnitude) or phase response (phase) indication Switch for scaling the amplitude axis to 25 dB (± 12.5 dB) or to 50 dB (± 25 dB) Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 425 Lo-Pass-, High-Pass- and All-Pass filters with 12dB/Oct 0.4...2.0 slope. (Allpass) 0 dB -18...+12 dB GAIN sets amplification (rising) or attenuation (lowering) of parametric EQs or Low-Shelving- and High- Shelving filters. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 426 Click on the third block in the Flow Diagram Selector or double click on the X-OVER block in the large Signal Flow Diagram to select the X-Over window. Presentation in the Graphic Display The following table lists the graphic displays different graphic renditions: Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 427 20 Hz and 20 12dB/Q=1.5, 12dB/Q=2.0, kHz is possible. Bessel 12dB, Butterworth 12dB, Linkwitz/Riley 12dB, Bessel 18dB, Butterworth 18dB, Bessel 24dB, Butterworth 24dB, Linkwitz/ Riley 24dB FREQ: 20 Hz...20 kHz Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 428 BYPASS activates (not engaged) or deactivates (enganged) the corresponding delay. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 429 Click on the fourth block in the Flow Diagram Selector or double click on the DYNAMICS block in the large Flow Diagram to select the Dynamics window. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 430 0 dBu the limiter sets in. 0.275... 8.696 V 5 ms 0...99 ms ATTACK defines how fast the gain is reduced after the signal level has declined the threshold level. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 431 Bessel and Butterworth types, and to -6 dB in the Linkwitz-Riley types. The cutoff frequency is continuously variable from 20 Hz to 20 kHz. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 432 Clicking with the right mouse button on the white dot and keeping the mouse button pressed down allows changing the Q-values (if SLOPE is set to 12dB) of the filter. Bosch Security Systems B.V. User Manual...
Page 433 A white dot in the frequency response display represents an active filter (BYPASS not engaged). Clicking with the left mouse button on this dot and keeping the mouse button pressed down allows changing the filter’s frequency by moving the mouse to the left or to the right. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 434 Fixed channel labeling: channels of a matrix of the dimension I x O are numbered from 1 to I. Text field for providing an input channel with an internal IRIS-Net name. CAUTION: The use of * (asterisk) and = (equal) in names is not permissible.
Page 435 MUTE button mutes the output signal. Text field for providing an output channel with an internal IRIS-Net name. CAUTION: The use of * (asterisk) and = (equal) in names is not permissible. Nodes...
Page 436 The notation I x O represents a matrix with I inputs and O outputs. The number of inputs (2 to 32) and outputs (2 to 32) can be selected when adding the DSP block to the configuration. Bosch Security Systems B.V. User Manual...
Page 437 Fixed channel labeling: channels of a matrix with the dimensions I x O are numbered from 1 to I. Text field for providing an input channel with an internal IRIS-Net name. CAUTION: The use of * (asterisk) and = (equal) in names is not permissible.
Page 438 0.0 dB 0...60 dB The input channel gain can be adjusted in steps of 6 dB. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 439 The DSP block Mixer allows mixing various input signals to output them via a single output (mono) or two outputs (stereo). Monaural and stereo mixers with 2, 4, 8, 16, 24 and 32 inputs are available. Bosch Security Systems B.V. User Manual...
Page 440 The Fader Display indicates the current fader setting as a numerical value and allows entering the desired value. Text field for labeling an input channel with an internal IRIS-Net name. CAUTION: The use of * (asterisk) and = (equal) in names is not permissible.
Page 441 (adjustable )width in the notch and less than infinite attenuation at the notch frequency. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 442 Q-values of the filter. PARAMETRIC EQ Equalizers accentuate or lower the audio signal within specific frequency ranges. IRIS-Net provides parametric 3-, 5-, 7- as well as 12-Band equalizers in monaural (1 input and 1 output) and stereo quality (2 inputs and 2 outputs) plus, in addition, PEQs with a freely selectable amount of filters between 1 and 32.
Page 443 EQs or low shelving and high shelving equalizers. depends 20 Hz...20 FREQ (frequency) sets the center frequency of a parametric EQ or the cut-off frequency of shelving and Hi / Lo pass filters. number of filters Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 444 An input signal with priority 0 assigned to an output gets connected through to the output in any case. If another signal (with another priority) is present at the output, it is mixed with the signal that has priority 0. For priority mode "horizontal" only: Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 445 Description Fixed channel labeling: channels are numbered from 1 to I. Text field for providing an input channel with an internal IRIS-Net name. CAUTION: The use of * (asterisk) and = (equal) in names is not permissible. 0...255 The Priority field shows the input channel’s set priority.
Page 446 Entering the desired value in dB is possible as well. MUTE button mutes the output signal. Textfeld zur Beschriftung des Eingangskanals mit einer IRIS-Net-internen Bezeichnung. CAUTION: The use of * (asterisk) and = (equal) in names is not permissible. Nodes...
Page 447 BYPASS activates (not engaged) or deactivates (engaged) the Limiter, which allows for quick A / B comparison between the limited and unlimited audio signal. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 448 5 ms 0...50 ms ATTACK defines how fast the gain is reduced after the signal exceeds the threshold level. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 449 0 ms 0...50 ms ATTACK defines how fast the gain is reduced after the signal exceeds the threshold level. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 450 Description The attenuation (gain reduction) indicator signals the degree of level reduction in dB. A red bar that increases from right to left indicates the degree of gain reduction. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 451 0.0 dB -18.0...+6.0 GAIN defines the compressor’s output amplification. GAIN allows matching input and output levels if compression lead to a level reduction of the output signal. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 452 IRIS-Net DIGITAL MATRIX | en RMS-COMPRESSOR (RCM-24) The characteristics of the Compressor (RCM-24) offered by IRIS-Net is identical to the compressors used in Precision Series power amps. Element Default Range Description This bar meter indicates gain reduction in dB, i.e. by how much the Compressor reduces the signal level.
Page 453 (Low-Shelving filter). The filter’s cut-off frequency is fixed to 666,6 Hz. The desired amplification or attenuation can be set by directly entering the desired value or by using the rotary control. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 454 Sine mode generates a sine signal with a constant frequency. Sweep mode generates a one-time or periodical sine sweep over a specific frequency range. Element Default Range Description The SINE button puts the tone generator in constant sine signal mode. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 455 The RS-232 interface is now ready for communication. ETHERNET SETTINGS Factory set values of the Ethernet port are: Parameter Setting IP address 192.168.1.100 Network mask 255.255.255.0 Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 456 /CLEAR execute none Deletes the existing log file /PRINT execute none Displays the existing log file /SAVE execute none Saves the log to a file "parser.log" in directory /flash/log Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 457 0, 1 State of remote device (0 = OK, 1 = REMOTEFAUL IDX1...IDX1 does not answer) 0, 1 State of condition (0 = false, 1 = true) CONDRESULT IDX1...IDX1 Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 458 Status of received Bundle (0 = NOT IDX1...IDX RECEIVED, 1 = ACTIVE) /SYSNAME /VALUE R / W max. 60 Name of device in CobraNet character /TXBUNDLE R / W 0...65535 Number of sent Bundle IDX1...IDX Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 459 IDX1...IDX 8, ALL /NAME R / W max. Input name IDX1...IDX 8, ALL charac ters /RAMPTIME R / W 0.001. Ramping Time of input (seconds) IDX1...IDX ..20 8, ALL Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 460 0.001... Ramping Time of input IDX1...IDX (seconds) 8, ALL /MIC.LINE R / W 0, 1 Selects input level (0 = Mic level, IDX1...IDX 1 = Line level) 8, ALL Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 461 Current Gain change as full scale GAINREDU value (32 bit) CTION Transform given value into dB by: 20 log (0x7FFFFF/ value) /HOLD /VALUE R / W 50...60000 Hold time in ms Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 462 20 log (256 * value / 0x7FFFFF) + 10 log (2) /HOLD /VALUE R / W 10...1000 Hold time in ms /VALUE R / W 10...3000 Time for GAIN INCREASE in ms INCREASE TIME Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 463 0, 1 Polarity of inputs (0 = normal, 1 POLARITY IDX1...I = inverted) /VALUE R / W 0, 1 Polarity of output (0 = normal, 1 POLARITY = inverted) Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 464 20 log (256 * value / 0x7FFFFF) + 10 log (2) /VUOUT /VALUE value1 Output level value2 Transform given values into dB by: 20 log (value1 / 0x7FFFFF) + value2 Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 465 Threshold in dB THRESHOL VALU Commands for Delay Read Write Values Description /DSP /BYPASS /VALUE R / W 0, 1 0 = Bypass not activated, 1 = PARA DELA Bypass activated Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 466 0 = Level 2 (+/- 1000 ppm) 1 = Level 3 (variable pitch) 2 = Level 1(+/- 50 ppm, high accuracy) 3 = reserved /COPYRIGHT 0, 1 Copyright bit of input signal IDX1...IDX Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 467 8, ALL /SAMPLERATE Sample rate of input signal IDX1...IDX /SRCBYPASS R / W 0, 1 Sample Rate Converter Bypass IDX1...IDX (0 = Bypass not activated, 1 = Bypass activated) Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 468 0 = normal, 1 = inverted POLARITY IDX1...I DX8, /NAME R / W max. 16 Output name IDX1...I charact DX8, R / W 0.001... Ramping Time of faders (in RAMPTIM IDX1...I seconds) DX8, Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 469 /MIXMIC R / W -30...0 Gain of MIC input VALU /RELEASE R / W 5...1000 Release time in ms VALU R / W -15...21 Threshold in dB THRESHOL VALU Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 470 _GAIN /RATIO R / W 1...10 Compressor ratio VALUE /RELEASE / R / W 10...1000 Release time in ms VALUE R / W -84...-25 Threshold in dB THRESHO VALUE Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 471 1...60 Read description of preset PRESET_INFO_READ /PRESET_SET_DESC W 1...60 Set description of preset (max. descrip- 32 characters) tion /PRESET_SET_PROP W 1...60 Set mute/unmute of preset MUTE/ during load NOMUTE Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 472 /IDX1...IDXn R / W 0, 1 0 = Bypass not activated, 1 = PARA GRAPHIC BYPASS Bypass activated EQ_x /VALUE R / W 20...1000 Frequency of LF FILTER LOWFR Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 473 Type des LF FILTER Loshelv, Hishelv, Hipass, Lopass /IDX2 R / W for future use /IDX3 R / W 0 = PEQ, Type of HF FILTER Loshelv, Hishelv, Hipass, Lopass Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 474 R / W 1...8 Compressor ratio COMPRESSO R.RATIO /COMPRES- /VALUE R / W 50...999 Release time in ms SOR.RELEAS /VALUE R / W -9...21 Threshold in dB COMPRESSO R.THRESHOL Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 475 R / W 10...999 Release time in ms LIMITER.RELE /VALUE R / W -9...21 Threshold in dB LIMITER.THR ESHOLD /XOVER.GAIN /VALUE R / W -30...6 Gain of crossover ways. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 476 12dB/ Q1.2, 8 = 12dB/ Q1.5, 9 = 12dB/Q2.0, 10 = 12dB-Bessel, 11 = 12dB-Butterworth, 12 12dB-Linkwitz, 13 = 18dB-Bessel, 14 = 18dB-Butterworth, 15 24dB-Bessel, 16 = 24dB-Butterworth, 17 = 24dB-Linkwitz Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 477 -80...0 Gain of crosspoint. IDX1...IDX Crosspoints are numbered column by column from top left to bot- tom right. /GAININ R / W -80...0 Gain of inputs 1 to n of IDX1...IDX matrix Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 478 0, 1 0 = normal, 1 = inverted POLARITY /SIGNAL /IDX1...IDXn 0, 1 Signal LED of inputs and outputs /SOLO /IDX1...IDXn R / W 0, 1 Solo of inputs Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 479 IDX1...IDXn Oct, 2 = 12dB/Oct) /TYPE R / W 0,1,2,3,4,5 0 = PEQ, 1 = Loshelv, 2 = Hishelv, 3 = IDX1...IDXn Hipass, 4 = Lopass, 5 = Allpass Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 480 /IDX1...IDXn 0...255 Priority of inputs PRIORITYPA GINGLINE Commands for Router Values Description Writ /ROUTING 0...n Connected crosspoint of output 1 PARA ROUTER POINTS IDX1...IDX to m of router Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 481 (e.g. IDX1 = HIGH, IDX2 = MID, IDX3 = LOW) 20...2000 Frequency of hipass. Ways are HIPASS.FR IDX1...IDXn numbered top-down. (e.g. IDX1 = HIGH, IDX2 = MID, IDX3 = LOW) Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 482 16 = 24dB- Butterworth, 17 = 24dB- Linkwitz /MUTE 0, 1 0 = not muted, 1 = muted IDX1...IDXn /POLARITY 0, 1 0 = normal, 1 = inverted IDX1...IDXn Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 483 0, 1 0 = Bypass not activated, 1 = Bypass DELAYBY IDX1...IDX250 activated PASS DELAYVAL IDX1...IDX250 0, 1 0 = Bypass not activated, 1 = Bypass EQ1BYPA IDX1...IDX250 activated Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 484 0, 1, 2 Routing of output A (0 = A, 1 = B, 2 = A+B) IDX1...IDX250 0, 1 0 = Bypass not activated, 1 = Bypass COMPBY IDX1...IDX250 activated PASS Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 485 Q1.2, 8 = 12dB/Q1.5, 9 = 12dB/Q2.0, 10 = 12dB-Bessel, 11 = 12dB-Butterworth, 12 = 12dB-Linkwitz, 13 = 18dB-Bessel, 14 = 18dB-Butterworth, 15 = 24dB-Bessel, 16 = 24dB-Butterworth, 17 = 24dB- Linkwitz Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 486 IDX1...IDX250 0.4...40 Quality of equalizer 1 EQ1QUAL IDX1...IDX250 /EQ2... (same as above, but for equalizer 2 to 5) IDX1...IDX250 /EQ5... /OUTPB ... (same as above, but for output B) Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 487 State of the two GPIs. The value 0 means „not activated“, so the input is open (high impedance). The value 1 means „activated“, so the input is connected (low impedance) to signal earth. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 488 0 = not muted, 1 = muted Link-Numbers for linking adjacent ways of a crossover Number of crossover ways Link-Number Hexadecimal representation of remote amplifiers connected to the device Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 489 Apart from the Ethernet network interface the N8000 also supports a USB interface. The USB driver is located in the \IRIS-Net\Driver\USB Netmax Driver folder and must be installed before the USB interface can be used. The N8000 can then be configured using the USB interface by selecting the Configuration via USB menu item in the Netmax menu of IRIS-Net.
Page 490 If the Ethernet network contains a DHCP server, it can be used to automatically and DHCP server conveniently configure the N8000’s Ether- net interface. NAME Internal IRIS-Net name of the N8000. ACTIVE PRESET Name of the currently loaded preset. Changing presets is possible via the Preset Manager. START-UP PRESET Name of the currently selected start-up preset.
Page 491 10. Reload the DM-1 Web Interface in the browser after the power cycle. 11. Click on the Upgrade Firmware button in the DM-1 Web Interface. 12. Open the folder /Firmware/DM-1 in the installation directory of IRIS-Net. 13. Select the file DLM-failsave-update.dnt and start the update process.
Page 492 Version V3.4.3-RC2. A complete firmware update to V3.4.2 (including failsafe & capability image) has to be done before the module is updated to the newest firmware version V3.4.3. OM-1 Firmware Update For updating the OM-1 firmware, use the OMNEO firmware upload tool (see directory /tools in the IRIS-Net installation directory). N8000 Browser Interface The browser interface of the N8000’s integrated web server is part of IRIS-Net’s existing possibilities for configuring...
Page 493 As shown in the screenshot below, a warning appears when you try to log in while another user already employs the browser interface. Completing the login at this point will exclude (log out) any other user from the active session. Bosch Security Systems B.V. User Manual...
Page 494 AM CET clocks are forwarded one hour to 3:00 AM CEST. CEST ends on the last Sunday in October when at 3:00 AM CEST clocks are set back one hour to 2:00 AM CET. Bosch Security Systems B.V. User Manual...
Page 495 The signaling of errors for which the Hold option has been selected is not reset, even if they occur only temporarily. This option is especially useful for detecting sporadic network errors. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 496 Memory/Configuration data error, please refer to tables DSP Faults and RCM Faults for Fault further detail Hardware Hardware Configuration fault in the N8000, please refer to table DSP Faults for further detail Configuration Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 497 IRIS-Net DIGITAL MATRIX | en Input Supervision Fault in Pilot Tone Detection (PLT) Temperature N8000 thermal overload Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 498 The DSP configuration requires a CobraNet board installed in the network module slot, but there is no board installed Cobranet Interface An error occurred during communication with the CM-1 interface Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 499 Ethernet which the N8000 slave unit has to answer. The N8000 slave unit signals a Heartbeat Fault whenever the periodic request has not been received while the N8000 server, on the other hand, signals a Remote N8000 Fault. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 500 If the Error check of connected device configuration is selected for one of the RS-232 ports, the user can use the corresponding Configure button to open the Error Check Parameters window to set interface transmission method and polling parameters. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 501 The entered value has to be in the range of 1 and 32 because the maximum number of nodes included in a row of a priority matrix is 32. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 502 Telnet Setup The Telnet Setup page allows activating the telnet connection of the device. To activate the telnet connection select the checkbox “Accept Telnet Connections”, then click Save Settings. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 503 IRIS-Net DIGITAL MATRIX | en The Set Telnet Password dialog appears. Enter a password and click Set Password. Notice! A minimum password length of 8 characters is strongly recommended. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 504 System status or change in state messages are referred to as events. Event types can be selected in two different ways: by event level or by event facility, where the latter describes a specific system part of the N8000. Event Levels Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 505 Pilot Tone Detection information Parser ASCII Control Protocol information Wall station Information concerning connected Wall stations The Event Log window lists the events in consecutive order including date and time stamp. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 506 The Main Setup page allows activating or deactivating the Task Manager of the N8000. HINT: Editing Conditions, Macros and Triggers is only possible when the Task Manager is deactivated. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 507 The N8000 is capable of managing up to 100 Conditions. Whether commands are being executed depends on Conditions. Commands to be executed are defined as Macros. Whether a Conditions result is true or false depends on the type of Condition and its respective parameters. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 508 0V...2V and 8V...10V only. On the other hand, if the input voltage is in the range of 2 volts and 8 volts, that is, if the input voltage is in a voltage range that is not feasible for using the inputs as digital input, the condition is true which results in error indication. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 509 The screenshot on the left shows the condition "EInterface". The conditions result is true whenever a fault is recognized on the N8000 interface. The following types of errors are available to select from: CobraNet, CAN Bus, GPI and RS-232 interface. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 510 Example: The screenshot on the left shows the condition "Temp High". This conditions result is true as long as the temperature stays above the maximum allowable temperature of 50°C. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 511 N8000. This is achieved by inverting Condition 1 "TempHigh" and Condition 2 "EInterface" and combining the results with the logic operation AND. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 512 "Amplifier X" represent remote amps with the CAN address X that are connected to the CAN bus. The conditions result is true if one or all of the selected amplifiers are in the selected status. Bosch Security Systems B.V. User Manual...
Page 513 CAN addresses between 1 and 4 are powered on. Macros The N8000 is capable of managing up to 100 macros. Macros are used to change the state of the N8000 or the states of connected remote amps. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 514 Amplifier Power: Execution of this macro switches power amps on or off. Amps specified in the amplifier list as "Amplifier X" represent remote amps with CAN address ”X” that are connected to the CAN bus. Bosch Security Systems B.V. User Manual...
Page 515 Digital Output: Execution of this macro changes the (digital) state of a control output of the N8000. It is possible to – set (relay contact closed, i.e. connected to ground), – reset (relay contact open) or – invert a control output. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 516 Device list has to be done in the Remote Devices window. User Fault: Execution of this macro assigns a random numerical Error Code to the selected User Fault.. HINT: ErrorCode"0"represents"noerror". Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 517 Sequence: Execution of this macro sequentially executes up to five other macros. Each macro of a sequence can depend on a condition. Conditions are defined on the Conditions page. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 518 Save Amplifier Preset: The current settings of the selected amps are stored in a selected User Preset. Amps specified in the amplifier list as „Amplifier X“ represent remote amps with CAN address „X“ that are connected to the CAN bus. Bosch Security Systems B.V. User Manual...
Page 519 IRIS-Net DIGITAL MATRIX | en LoadN8000Preset.Execution of this macro loads a selected Preset into the N8000. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 520 Save N8000 Preset: The macro saves the current settings of the N8000’s DSP configuration in a Preset. Preset number and preset name are user-definable. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 521 IRIS-Net DIGITAL MATRIX | en Triggers Triggers control the execution of macros depending on a specific state of a Condition. Up to 100 triggers can be employed. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 522 Up to 100 remote N8000 can be used in remote macros. Enable Allows deactivating a remote N8000 temporarily. IP Address The IP address of the remote N8000. Password The password of the user account „netmax“ of the remote N8000. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 523 Pressing the Upload Firmware button loads the selected firmware file into the memory buffer of the N8000. Pressing the Update button writes the new firmware into the N8000, which automatically reboots upon successfully completing the update process. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 524 Keep existing TCP/IP set- tings... checkbox. Pressing the Store Configuration button actually stores the uploaded configuration data in the N8000. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 525 N8000. In addition, loading a backup file (via Upload Configuration) into a number of N8000 System Controllers offers a quick and very convenient way to configure several N8000 absolutely identically. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 526 N8000 is currently part of an existing Ethernet network and settings such as IP address must be retained. Reboot The Reboot page allows rebooting the N8000. Rebooting the N8000 also terminates the current session of the browser interface. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 527 The use of special characters is not permissible. The password is case-sensitive. When logged in as administrator, the Change User Password page allows the assignment of new passwords to all users. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 528 The Boot Settings page is only accessible if you are logged in as administrator. Changing parameters on this page is not recommended. If you are in doubt, please, leave the pre-set values as they are. Bosch Security Systems B.V. User Manual...
Page 529: Touch Panels
TPI-5 Device First, create a TPI-5 Device in your IRIS-Net project, by selecting it from the Object List in the category Accessories and Misc. Hardware > Touchpanels. Alternatively select and drag and drop it to the worksheet from the window Accessories and Misc.
Page 530 P64, then the TPI-5 can't go online with the N8000 / P 64. General Error General Error in the TPI-5. N8000 Master Fault The Master Fault Flag of a N8000 / P64, which is connected to the TPI-5, is active. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 531 Activate the power supply system of the TPI-5. After some seconds an IRIS-Net project signals the successful start activity of the TPI-5. Start the IRIS-Net software on your PC. Click on Tools > Device Scan.
Page 532 Connect the network connection of your PC to the Ethernet interface of the TPI-5 with a crossover cable, or with a patch cable and a hub/switch. Activate the power supply system of the TPI-5. After some seconds a IRIS-Net project signals the successful start activity of the TPI-5. Bosch Security Systems B.V. User Manual...
Page 533 The message "Welcome to IRIS" is indicated. Enter doc*update=start and tap the return button. Figure 5.1: The IRIS-Net Update Server dialog appears on the screen of the TPI-5. The TPI-5 is now ready to receive. Start the IRIS-Net application on your PC.
Page 534 IRIS-Net TOUCH PANELS | en Select the entry IRIS-Net TPI in the Device Type list. All connected Touch Panels are shown in the Devices list. Select the Touch Panel from the Devices list that has to be updated. 10. Right click on the entry in the Devices list.
Page 535 After successful transmission the name of the transmitted project file is indicated in the IRIS-Net Update Server dialog on the touch panel. 14. Click on button Reload latest Project in the IRIS-Net Update Server dialog at the Touch Panel. . The new project is loaded Bosch Security Systems B.V.
Page 536 Updating the IRIS-Net application file The purpose of this procedure is to build a connection between a PC and a TPI-5 and updating the IRIS-Net project file of the TPI-5. In the following it is assumed that the file to be transferred is available at the PC and the network settings are set to factory defaults.
Page 537 Start the IRIS-Net application on your PC. Click on Tools > Device Scan. The dialog Device Scan appears. Select the entry IRIS-Net TPI in the Device Type list. All connected Touch Panels are shown in the Devices list. Bosch Security Systems B.V.
Page 538 11. Click on the button Send Application Package in the Update Dialog. The application file is now sent to the TPI-5. During the transmission a progress bar will pop up. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 539 IRIS-Net TOUCH PANELS | en Figure 5.3: After successfull transmission the file size and date of the application file is indicated in the IRIS-Net Update Ser- ver dialog on the TPI-5. 12. Click on button Update Application in the IRIS-Net Update Server dialog on the Touch Panel. The new Application Package will be extracted and installed.
Page 540: Tpi-8/Tpi-12
Consequences The purpose of this procedure is to build a connection between a PC and a TPI-8/TPI-12 and updating the IRIS-Net project file of the TPI-8/TPI-12. In the following it is assumed that the file to be transfered is available at the PC.
Page 541 IRIS-Net TOUCH PANELS | en Figure 5.4: The dialog IRIS-Net Update Server appears at the screen of the TPI-8/TPI-12. The TPI-8/TPI-12 is now ready-to- receive. Start IRIS-Net application on your PC. Click on Tools > Device Scan. The dialog Device Scan appears.
Page 542 IRIS-Net TOUCH PANELS | en Select the entry IRIS-Net in the Device Type list. All connected Touch Panels are shown in the Devices list. Select the Touch Panel from the Devices list that has to be updated. 10. Right click on the entry in the Devices list.
Page 543 V1.8.0 or newer. For older version of IRIS-Net (e.g. V1.7.1) please see page 404. The purpose of this procedure is to build a connection between a PC and a TPI-8/TPI-12 and updating the IRIS-Net project file of the TPI-8/TPI-12. In the following it is assumed that the file to be transferred is available at the PC.
Page 544 The message “Welcome to IRIS“ is indicated. Enter doc*update=start and tap the return button. Figure 5.5: The dialog IRIS-Net Update Server appears at the screen of the TPI-8/TPI-12. The TPI-8/TPI-12 is now ready-to- receive. Bosch Security Systems B.V. User Manual...
Page 545 Click on Tools > Device Scan. The dialog Device Scan appears. Select the entry IRIS-Net in the Device Type list. All connected Touch Panels are shown in the Devices list. Select the Touch Panel from the Devices list that has to be updated.
Page 546 11. If Archive not yet created! is indicated next to the Create Application Package button, click on the Create Application Package button. Figure 5.6: An application package is generated from the currently running IRIS-Net application. The file size and date of the generated package is indicated next to the Create Application Package button when finished.
Page 547 IRIS-Net TOUCH PANELS | en 17. To restore the previous version of IRIS-Net, turn off the power supply system of the Touch Panel. The previous version of IRIS-Net will be loaded when switching on the Touch Panel next time. Hot to update for IRIS-Net V1.8.3 and older HINT: The following description refers to IRIS-Net versions older than V2.0.
Page 548 The file is now sent to the TPI-8/TPI-12. The successful transmission is indicated by message “success” in the Update Mode dialog at the PC and also the TPI-8/TPI-12. 11. Enter doc*update=reboot and tap the return button. The TPI-8/TPI-12 reboots and uses the new IRIS-Net project file or IRIS-Net application. Bosch Security Systems B.V. User Manual...
Page 549: Digital Sound Processor
The overall signal processing is performed by two 24-bit Motorola signal processors. Additional Features are: – FLASH memory for software and preset updates via serial interfaces – PC-based operation and configuration software IRIS-Net – Standard MIDI-interface and RS-232 interface – RS-485 interface or switching contacts optionally available –...
Page 550 CONFIGURATION OF THE INTERFACE For using the Dx38 device in IRIS-Net the used COM port of the PC has to be selected. When using an USB-RS-485 adapters the system internal COM port can be found in the Control Panel, see following picture.
Page 551 IRIS-Net DIGITAL SOUND PROCESSOR | en In this example COM port 3 is used by the adapter. The value „COM3” must be entered for the Property „hardware” of the serial interface in IRIS-Net. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 552 RS-485 bus. These LEDs indicate, which frequency band the corresponding channel is set to. If a channel is configured for full range operation, all its func- tion-LEDs are simultaneously lit. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 553 RACE file import. MASTER EQ The MASTER EQ page provides access to the two 5-band parametric equalizers of the sound system processor inputs. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 554 RACE files are also accessible from this window. The FLOW DIAGRAM window opens when clicking on the first, fourth or eight block in the Flow Diagram Selector. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 555 Clicking with the right mouse button opens the Copy & Paste menu, which allows copying all parameters of the corresponding EQ block to any other EQ block within the same project. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 556 The EDITED indicator provides information whether a parameter has been altered since the last RECALL. If the indicator lights red, parameters have been edited and therefore differ from the ones of the preset that is shown. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 557 If the sound system processor is operated in Full Edit Mode, clicking the button LED Config opens the LED Configuration dialog. Recall a Presets Element Description DClicking the button RECALL... opens the Recall Preset dialog, where you can select and recall a Preset. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 558 In the worst case, this could lead to severe damage to the connected loudspeaker cabinets due to improper signal processing! Consequences Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 559 IRIS-Net allows the storing of all DSP parameters of an sound system processor together with the according preset name in a file, and to load sound system processor parameters from these files. Therefore, IRIS-Net creates a sub- directory \Presets during installation, where all factory-presets are saved in to. It is recommended to save your own presets in this directory as well.
Page 560 IRIS-Net DIGITAL SOUND PROCESSOR | en Import of EV RACE Files IRIS-Net allows importing loudspeaker presets that have been created in Electro-Voice RACE. Element Description Clicking IMPORT RACE FILE opens the Import RACE File dialog. First, you have to select the desired RACE file by use of the Browse... button. Because a RACE file can hold the data of up to 31 EV Dx38, you need to continue by selecting the desired device from the RACE file within the dialog ”SELECT...
Page 561 A click with the right mouse button opens the ”Copy & Paste” menu, which allows convenient copying all EQs of the corresponding out- put to any other EQ-filter bank within the same project. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 562 (depending on the selected filter type) by Bosch Security Systems B.V. User Manual...
Page 563 You can select the master delay window by clicking onto the third block in the Flow Diagram Selector or onto the MASTER DELAY block in the flow diagram. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 564 Except for the possibility to select ”All pass” as filter type, these filters are identical to the ones of the Master-EQ's. The Channel-EQ is selected by clicking on the fifth block of the flow diagram selector or by on the CHANNEL EQ block in the full-scale flow diagram. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 565 “electrical” graphs are indicated in dark colors. Selecting ”separate” results in a separated display of the sound system processor channels’ transfer functions while ”sum” shows the summed signal of the sound system processor channels. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 566 Q defines the quality or bandwidth of a parametric EQ. A high Q-value (PEQ), results in a narrowband filter, 0.4...2.0 (Hi-/ while a small Q-value results in a broadband filter. The Q-value also sets the quality and thus the Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 567 Clicking on the sixth block in the Flow Diagram Selector or on the X-OVER block in the large signal flow diagram opens the X-Over window. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 568 ”electrical” graphs are drawn in dark colors. The ”Separate” switch allows separate indication of the two amplifier channels’ transfer functions. The ”Sum” switch causes display of the summed signal of the two channels. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 569 LO-PASS 12dB, Linkwitz/Riley 12dB, filter to any LO-PASS filters within the same project. Bessel 18dB, Butterworth 18dB, Bessel 24dB, Butterworth 24dB, Linkwitz/ Riley 24dB FREQ: 20 Hz...20 kHz Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 570 ”lights” in color as soon as the mouse cursor is positioned on top of the corresponding white dot to provide improved overview and handling. An extra white graph is displayed in addition, representing the frequency response of the corresponding selected filter. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 571 A click with the right mouse button on this field opens the Copy & Paste menu, which allows copying all dynamics parameters of the corresponding channel to any other channels within the same project. Bosch Security Systems B.V. User Manual...
Page 572 BYPASS switches the limiter on (button is not engaged) or off (button is engaged). This allows quick A / B-comparison of the limited and non-limited audio signals. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 573 Nevertheless, they provide the user with the possibility for creating loudspeaker systems presets of a higher Bosch Security Systems B.V. User Manual...
Page 574 Clicking the button LOAD SPEAKER FILE opens a dialog that allows the selection of the desired speaker file. The name of the loaded loudspeaker model is shown in the black-shaded field. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 575 Setting an amount from 1 to 8 is possible. Clicking the CLEAR SPEAKER DATA button clears the previously loaded measured speaker data of the selected channel. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 576 The overall signal processing is performed by two 24-bit Motorola signal processors. Additional features are: – FLASH memory for software and preset updates via serial interfaces – PC-based operation and configuration software IRIS-Net – Standard MIDI-interface and RS-232 interface – RS-485 interface or switching contacts optionally available –...
Page 577 CONFIGURATION OF THE INTERFACE For using the DSP 244 device in IRIS-Net the used COM port of the PC has to be selected. When using an USB-RS-485 adapters the system internal COM port can be found in the Control Panel, see following picture.
Page 578 IRIS-Net DIGITAL SOUND PROCESSOR | en In this example COM port 3 is used by the adapter. The value „COM3” must be entered for the Property „hardware” of the serial interface in IRIS-Net. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 579 These keys allow to mute the output signal of the corresponding output channels. Pressing a key once switches the mute-function ON; the key’s red LED lights. Pressing the button again switches the mute-function OFF; the key’s LED is dimmed again. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 580 This page allows the programming of delay lines for the channels A and B as well as for the summed input A+B. CHANNEL EQ The CHANNEL EQ page offers access to the 4-band parametric equalizers of the sound system processor outputs for speaker equalization. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 581 RACE files are also accessible from this window. The FLOW DIAGRAM window opens when clicking on the first, fourth or eight block in the Flow Diagram Selector. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 582 Clicking with the right mouse button opens the Copy & Paste menu, which allows copying all parameters of the corresponding EQ block to any other EQ block within the same project. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 583 The EDITED indicator provides information whether a parameter has been altered since the last RECALL. If the indicator lights red, parameters have been edited and therefore differ from the ones of the preset that is shown. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 584 If the sound system processor is operated in Full Edit Mode, clicking the button LED Config opens the LED Configuration dialog. Recall a Presets Element Description Clicking the button RECALL... opens the Recall Preset dialog, where you can select and recall a Preset. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 585 Store is only possible if a user program number is selected. Clicking the STORE TO..button opens the Store To Preset dialog. In this dialog the Program Number can be selected and the corresponding Program Name can be entered. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 586 IRIS-Net allows the storing of all DSP parameters of an sound system processor together with the according preset name in a file, and to load sound system processor parameters from these files. Therefore, IRIS-Net creates a sub- directory \Presets during installation, where all factory-presets are saved in to. It is recommended to save your own presets in this directory as well.
Page 587 In many cases post-mixing console parametric equalization becomes redundant. The Master- EQ is selected by clicking on the second block of the flow diagram selector or on the MASTER EQ block in the full-scale flow diagram. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 588 A click with the right mouse button opens the ”Copy & Paste” menu, which allows convenient copying all EQs of the corresponding out- put to any other EQ-filter bank within the same project. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 589 BYPASS switches the corresponding filter ON (not engaged) or OFF (engaged), which allows for quick A / B-evaluation of the actual effect that a filter has on the sound. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 590 You can select the master delay window by clicking onto the third block in the Flow Diagram Selector or onto the MAS- TER DELAY block in the flow diagram. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 591 Master- EQ's. The Channel-EQ is selected by clicking on the fifth block of the flow diagram selector or by on the CHANNEL EQ block in the full-scale flow diagram. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 592 “electrical” graphs are indicated in dark colors. Selecting ”separate” results in a separated display of the sound system processor channels’ transfer functions while ”sum” shows the summed signal of the sound system processor channels. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 593 Q defines the quality or bandwidth of a parametric EQ. A high Q-value (PEQ), results in a narrowband filter, 0.4...2.0 (Hi-/ while a small Q-value results in a broadband filter. The Q-value also sets the quality and thus the Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 594 Clicking on the sixth block in the Flow Diagram Selector or on the X-OVER block in the large signal flow diagram opens the X-Over window. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 595 ”electrical” graphs are drawn in dark colors. The ”Separate” switch allows separate indication of the two amplifier channels’ transfer functions. The ”Sum” switch causes display of the summed signal of the two channels. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 596 LO-PASS 12dB, Linkwitz/Riley 12dB, filter to any LO-PASS filters within the same project. Bessel 18dB, Butterworth 18dB, Bessel 24dB, Butterworth 24dB, Linkwitz/ Riley 24dB FREQ: 20 Hz...20 kHz Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 597 ”lights” in color as soon as the mouse cursor is positioned on top of the corresponding white dot to provide impro- ved overview and handling. An extra white graph is displayed in addition, representing the frequency response of the corresponding selected filter. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 598 A click with the right mouse button on this field opens the Copy & Paste menu, which allows copying all dynamics parameters of the corresponding channel to any other channels within the same project. Bosch Security Systems B.V. User Manual...
Page 599 BYPASS switches the limiter on (button is not engaged) or off (button is engaged). This allows quick A / B-comparison of the limited and non-limited audio signals. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 600 A compressor’s / limiter’s title ”lights” in color as soon as the mouse cursor is positioned on top of the corresponding white dot to provide improved overview and handling. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 601 The summing display mode shows the result of sound system processor plus speaker transfer functions. Clicking on the Speaker tab in the Setup & Control window opens the Speaker page. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 602 Setting an amount from 1 to 8 is possible. Clicking the CLEAR SPEAKER DATA button clears the previously loaded measured speaker data of the selected channel. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 603: Dsp 600 Fir-Tune
To sum up, FIR-TUNE allows the linearization of frequency and phase of your DYNACORD loudspeakers. Activating FIRTUNE is as easy as loading a FIR Speaker Setting in the output channel of the DSP 600. The IRIS-Net software is used for loading Speaker Settings, and lots of DYNACORD FIR Speaker Settings are included. Please refer to the documentation of IRIS-Net for more details about using Speaker Settings.
Page 604 DSP 600 Device Start by creating an DSP 600 Device in your IRIS-Net project. Drag an DSP 600 from the Object Bar’s Devices category or from the Devices window into the worksheet (see also chapters: Devices and Configurations menu). Selected devices can be dragged around and repositioned at will.
Page 605 D/A- converters. Label of input or output channels, the labels can be edited at the Config & Info window. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 606 Config & Info The Config & Info window provides information and basic settings for the selected DSP 600. Additionally, editing labels and configuration of control port functions is possible as well. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 607 Shows the uptime of the DSP 600. Network Settings Element Default Description IP ADDRESS 192.168.1.100 IP address of the DSP 600 MAC ADDRESS MAC address of the DSP 600 Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 608 When signal transmission fails, the ERROR LED lights red. AES/EBU SAMPLE 32 to 192 Shows the sampling rate of the incoming signal when the input has RATE been successfully synchronized. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 609 Opens the Preset Recall for Port x dialog. This dialog allows assignment of a factory or user preset to the input. Preset Recall for Port x This dialog lists the 60 Factory Presets and 30 User Presets of the DSP 600. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 610 The Flow Diagram Selector can be accessed from any DSP page offering navigation means within the DSP signal processing functions. The Flow Diagram Selector lets you select different function blocks, where the actually selected block is displayed in a light grey engaged field. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 611 All parameters that are necessary for the saving, loading and previewing of presets are also accessible from this window. The FLOW DIAGRAM window opens when clicking on the first (IN), fifth (RTG) or 13. block (OUT) in the Flow Diagram Selector. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 612 Input Parametric EQ page. Clicking with the right mouse button opens the Copy & Paste menu, which allows copying all parameters of the corresponding EQ block to any other DSP 600 INPUT PEQ block within the same project. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 613 Clicking with the right mouse button opens the Copy & Paste menu, which allows copying all parameters of the corresponding ARRAY PEQ block to any other EQ block within the same project. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 614 Clicking with the right mouse button opens the Copy & Paste menu, which allows copying all parameters of the corresponding Delay block to any other DSP 600 Speaker Delay block within the same project. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 615 The EDITED indicator provides information whether a parameter has been altered since the last RECALL. If the indicator lights red, parameters have been edited and therefore differ from the ones of the preset that is shown. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 616 The loaded preset becomes instantly audible when in on-line mode. Be sure to select the desired preset with the correct set of parameters. In the worst case, this could lead to severe damage to the connected loudspeaker cabinets due to improper signal processing! Consequences Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 617 Clicking the ASSIGN .. button opens the Set Initial Preset... dialog. In this dialog a factory preset or user preset can be selected as startup preset. Clicking the X buttons clears the Startup preset selection. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 618 IRIS-Net allows the storing of all DSP parameters of an sound system processor together with the according preset name in a file on a PC, and to load sound system processor parameters from these files. Therefore, IRIS-Net creates a sub- directory \Presets during installation, where all factory-presets are saved in to. It is recommended to save your own presets in this directory as well.
Page 619 A click with the right mouse button opens the ”Copy & Paste” menu, which allows convenient copying all EQs of the corresponding output to any other DSP 600 Input PEQ filter bank within the same project. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 620 (Bypass), which allows for quick A / B-evaluation of the actual effect that a filter has on the sound. Press the EQ FLAT button to reset the gain of all filters to 0 dB. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 621 The Master-EQ is selected by clicking on the third block (GEQ) of the flow diagram selector or on the INPUT PROCES- SING GEQ block in the full-scale flow diagram. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 622 Deactivating every single EQ-Band is possible by setting this checkbox. Deactivating a band does not change the band’s previously made settings. Press the EQ FLAT button to reset the gain of all filters to 0 dB. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 623 You can select the input delay window by clicking onto the fourth block (DLY) in the Flow Diagram Selector or onto the INPUT PROCESSING DELAY block in the flow diagram. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 624 The Array Parametric EQ is selected by clicking on the sixth block (PEQ) of the flow diagram selector or onto the ARRAY CONTROL PEQ block in the full-scale flow diagram. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 625 The ”Sum” switch causes display of the summed signal of the output channels, including Output level and Mute. If the ”Sum ” switch is not pressed the output channels’ transfer functions are indicated separately. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 626 The Q-value also sets 0.4 to 2.0 the quality and thus the response of Hi, Lo and All pass (Hi-/Lo-/ filters with slopes of 12dB/oct.. Allpass) Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 627 You can select the Array Delay window by clicking onto the seventh block (DLY) in the Flow Diagram Selector or onto the ARRAY CONTROL DELAY block in the flow diagram. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 628 Delay allows delaying the corresponding output channel’s audio signal by an adjustable period of time. The caption of this button indicates the current state of the delay. Press the ACTIVE button to deactivate the delay. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 629 The Output Parametric EQ is selected by clicking on the eight block (PEQ) of the flow diagram selector or on the SPEAKER PROCESSING PEQ block in the full-scale flow diagram. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 630 The ”Sum” switch causes display of the summed signal of the output channels, including output level and mute. If the ”Sum ” switch is not pressed the output channels’ transfer functions are indicated separately. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 631 All pass filters with slopes of 12dB/oct.. Allpass) 0 dB -18 to +12 GAIN defines the amplification (increase) or attenuation (reduction) of parametric EQs or low shelving and high shelving equalizers. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 632 Clicking on the ninth block (XOV)in the Flow Diagram Selector or on the SPEAKER PROCESSING X-OVER block in the large signal flow diagram opens the X-Over window. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 633 The ”Sum” switch causes display of the summed signal of the output channels. If the ”Sum ” switch is not pressed the output channels’ transfer functions are indicated separately. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 634 HI-PASS filter to any HI- 12dB, Linkwitz/Riley 12dB, PASS filters within the same project. Bessel 18dB, Butterworth 18dB, Bessel 24dB, Butterworth 24dB, Linkwitz/ Riley 24dB FREQ: 20 Hz to 20 kHz Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 635 ”lights” in color as soon as the mouse cursor is positioned on top of the corresponding white dot to provide improved overview and handling. OUTPUT FIR Each output of the DSP 600 offers a 512 taps FIR filter. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 636 The ”Sum” switch causes display of the summed signal of the output channels. If the ”Sum ” switch is not pressed the output channels’ transfer functions are indicated separately. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 637 Press the ACTIVE button to deactivate the filter (Bypass), which allows for quick A / B-evaluation of the actual effect that the filter has on the sound. Adjusts the gain of the signal between -30 dB and +6 dB. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 638 Allows selection of the FIR filter type of the corresponding output channel. Press this button to generate the FIR filter. OUTPUT DELAY Individual output delays can be set for each output channel of the DSP 600. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 639 You can select the output delay window by clicking onto the eleventh block (DLY) in the Flow Diagram Selector or on the SPEAKER PROCESSING DELAY block in the flow diagram. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 640 Clicking on the 12. block (LIM) in the Flow Diagram Selector or double clicking on the SPEAKER PROCESSING LIMITERS block in the large flow diagram opens the Output Limiters window. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 641 A click with the right mouse button opens the ”Copy & Paste” menu, which allows convenient copying all limiter settings of the corresponding output to any other limiter within the same project. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 642 Press the ACTIVE button to deactivate the peak limiter. The ACTIVATED LED lights green if the TEMP limiter is active. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 643 A click with the left mouse button onto this dot and keeping the mouse button pressed down lets you set the threshold for the corresponding limiter by vertically dragging the mouse. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 644 The summing display mode shows the result of sound system processor plus speaker transfer functions. Clicking on the Speaker tab in the Configuration Panel opens the Speaker Dialog. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 645 Supervision & Test The Supervision window allows configuration of the test and pilot tone generator, additionally the status of the pilot tone detection is indicated. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 646 Activate the test generator for input channel A and/or input channel B. 0 dBu -80 to 0 dBu Enter the signal level for input channel A or B in dBu. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 647 (eye icon set) and can be edited (lock icon not set). Remove the eye icon of a parameter that should not be visible on the front panel. Activate the lock icon of a parameter that should not be editable at the front panel. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 648 IRIS-Net DIGITAL SOUND PROCESSOR | en Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 649: Dx46 Fir-Drive
To sum up, FIR-DRIVE allows the linearization of frequency and phase of your Electro-Voice loudspeakers. Activating FIRDRIVE is as easy as loading a FIR Speaker Setting in the output channel of the Dx46. The IRIS-Net software is used for loading Speaker Settings, and lots of Electro-Voice FIR Speaker Settings are included. Please refer to the documentation of IRIS-Net for more details about using Speaker Settings.
Page 650 Dx46 Device Start by creating an Dx46 Device in your IRIS-Net project. Drag an Dx46 from the Object Bar’s Devices category or from the Devices window into the worksheet (see also chapters: Devices and Configurations menu). Selected devices can be dragged around and repositioned at will.
Page 651 D/A-converters. Label of input or output channels, the labels can be edited at the Config & Info window. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 652 Config & Info The Config & Info window provides information and basic settings for the selected Dx46. Additionally, editing labels and configuration of control port functions is possible as well. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 653 Shows the software‘s version number. UPTIME Shows the uptime of the Dx46. Network Settings Element Default Description IP ADDRESS 192.168.1.100 IP address of the Dx46 MAC ADDRESS MAC address of the Dx46 Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 654 ERROR LED lights red. AES/EBU SAMPLE 32 to 192 Shows the sampling rate of the incoming signal when the input has RATE been successfully synchro- nized. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 655 Opens the Preset Recall for Port x dialog. This dialog allows assignment of a factory or user preset to the input. Preset Recall for Port x This dialog lists the 60 Factory Presets and 30 User Presets of the Dx46. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 656 A short description of each DSP page is provided in the following table. Please refer to the corresponding chapters for a more detailed explanation. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 657 All parameters that are necessary for the saving, loading and previewing of presets are also accessible from this window. The FLOW DIAGRAM window opens when clicking on the first (IN), fifth (RTG) or 13. block (OUT) in the Flow Diagram Selector. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 658 Input Parametric EQ page. Clicking with the right mouse button opens the Copy & Paste menu, which allows copying all parameters of the corresponding EQ block to any other Dx46 INPUT PEQ block within the same project. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 659 Clicking with the right mouse button opens the Copy & Paste menu, which allows copying all parameters of the corresponding ARRAY PEQ block to any other EQ block within the same project. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 660 Clicking with the right mouse button opens the Copy & Paste menu, which allows copying all parameters of the corresponding Delay block to any other Dx46 Speaker Delay block within the same project. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 661 The EDITED indicator provides information whether a parameter has been altered since the last RECALL. If the indicator lights red, parameters have been edited and therefore differ from the ones of the preset that is shown. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 662 The loaded preset becomes instantly audible when in on-line mode. Be sure to select the desired preset with the correct set of parameters. In the worst case, this could lead to severe damage to the connected loudspeaker cabinets due to improper signal processing! Consequences Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 663 Clicking the ASSIGN .. button opens the Set Initial Preset... dialog. In this dialog a factory preset or user preset can be selected as startup preset. Clicking the X buttons clears the Startup preset selection. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 664 IRIS-Net allows the storing of all DSP parameters of an sound system processor together with the according preset name in a file on a PC, and to load sound system processor parameters from these files. Therefore, IRIS-Net creates a sub- directory \Presets during installation, where all factory-presets are saved in to. It is recommended to save your own presets in this directory as well.
Page 665 A click with the right mouse button opens the ”Copy & Paste” menu, which allows convenient copying all EQs of the corresponding output to any other Dx46 Input PEQ filter bank within the same project. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 666 (Bypass), which allows for quick A / B-evaluation of the actual effect that a filter has on the sound. Press the EQ FLAT button to reset the gain of all filters to 0 dB. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 667 The Master-EQ is selected by clicking on the third block (GEQ) of the flow diagram selector or on the INPUT PROCES- SING GEQ block in the full-scale flow diagram. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 668 Deactivating every single EQ-Band is possible by setting this checkbox. Deactivating a band does not change the band’s previously made settings. Press the EQ FLAT button to reset the gain of all filters to 0 dB. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 669 You can select the input delay window by clicking onto the fourth block (DLY) in the Flow Diagram Selector or onto the INPUT PROCESSING DELAY block in the flow diagram. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 670 The Array Parametric EQ is selected by clicking on the sixth block (PEQ) of the flow diagram selector or onto the ARRAY CONTROL PEQ block in the full-scale flow diagram. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 671 The ”Sum” switch causes display of the summed signal of the output channels, including Output level and Mute. If the ”Sum ” switch is not pressed the output channels’ transfer functions are indicated separately. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 672 The Q-value also sets 0.4 to 2.0 the quality and thus the response of Hi, Lo and All pass (Hi-/Lo-/ filters with slopes of 12dB/oct.. Allpass) Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 673 You can select the Array Delay window by clicking onto the seventh block (DLY) in the Flow Diagram Selector or onto the ARRAY CONTROL DELAY block in the flow diagram. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 674 Delay allows delaying the corresponding output channel’s audio signal by an adjustable period of time. The caption of this button indicates the current state of the delay. Press the ACTIVE button to deactivate the delay. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 675 The Output Parametric EQ is selected by clicking on the eight block (PEQ) of the flow diagram selector or on the SPEAKER PROCESSING PEQ block in the full-scale flow diagram. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 676 The ”Sum” switch causes display of the summed signal of the output channels, including output level and mute. If the ”Sum ” switch is not pressed the output channels’ transfer functions are indicated separately. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 677 FREQ (frequency) sets the center frequency of a 250 / 1k 20 kHz parametric EQ or the cut-off frequency of shelving and Hi / / 4k / 16k Lo pass filters. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 678 Clicking on the ninth block (XOV)in the Flow Diagram Selector or on the SPEAKER PROCESSING X-OVER block in the large signal flow diagram opens the X-Over window. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 679 The ”Sum” switch causes display of the summed signal of the output channels. If the ”Sum ” switch is not pressed the output channels’ transfer functions are indicated separately. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 680 HI-PASS filter to any HI- 12dB, Linkwitz/Riley 12dB, PASS filters within the same project. Bessel 18dB, Butterworth 18dB, Bessel 24dB, Butterworth 24dB, Linkwitz/ Riley 24dB FREQ: 20 Hz to 20 kHz Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 681 A filter’s title ”lights” in color as soon as the mouse cursor is positioned on top of the corresponding white dot to provide improved overview and handling. OUTPUT FIR Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 682 The Output FIR is selected by clicking on the tenth block (FIR) of the flow diagram selector or on the SPEAKER PRO- CESSING FIR block in the full-scale flow diagram. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 683 FIR filter parameters together with the corresponding file name. ".gkf" is automatically added as file extension. Clears the current FIR filter settings. A Default-FIR-Filter (Thru) is activated instead. Clicking on the NEW button opens the Filter Design dialog. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 684 21 to 20000 LO Pass sets the cut-off frequency of the Lo pass filter. 40 dB 21 to 100 dB STOP RIPPLE sets the slope of the FIR filter. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 685 You can select the output delay window by clicking onto the eleventh block (DLY) in the Flow Diagram Selector or on the SPEAKER PROCESSING DELAY block in the flow diagram. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 686 Clicking on the 12. block (LIM) in the Flow Diagram Selector or double clicking on the SPEAKER PROCESSING LIMITERS block in the large flow diagram opens the Output Limiters window. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 687 A click with the right mouse button opens the ”Copy & Paste” menu, which allows convenient copying all limiter settings of the corresponding output to any other limiter within the same project. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 688 Press the ACTIVE button to deactivate the peak limiter. The ACTIVATED LED lights green if the TEMP limiter is active. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 689 The summing display mode shows the result of sound system processor plus speaker transfer functions. Clicking on the Speaker tab in the Configuration Panel opens the Speaker Dialog. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 690 Description Switch for selecting output 1, 2, 3, 4. 5 or output 6 for limiter editing. The name of the loaded loudspeaker model is shown in the black-shaded field. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 691 Supervision & Test The Supervision window allows configuration of the test and pilot tone generator, additionally the status of the pilot tone detection is indicated. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 692 (eye icon set) and can be edited (lock icon not set). Remove the eye icon of a parameter that should not be visible on the front panel. Activate the lock icon of a parameter that should not be editable at the front panel. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 693 IRIS-Net DIGITAL SOUND PROCESSOR | en Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 694: Dx46 And Dsp 600
"?" can be utilized to query parameter settings or commands of the corresponding level. To step down one level you have to enter "..". Use "/" to get back to level 1. Bosch Security Systems B.V. User Manual...
Page 695 Indicates the highest number of all control inputs with state „0“. /PORT1 Preset to be loaded when Port 1 is closed. /PORT5 Preset to be loaded when Port 5 is closed. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 696 Read locked state /ERROR ON, OFF Read error state (OFF = no error) Read sample rate in kHz SMPRATE /ETH /MAC Read MAC address Read or write IP address Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 697 Write to save a user preset. /LIST List of all presets. DEVICE PARAMETER INDEX TABLE Index Parameter Values Description /IDX00 lock flag list for device NONE, 0 to 9 “Set” means locked parameters Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 698 0 = peq, 1 = loshelv, 2 = hishelv, 3 = locut, 4 = hicut, 5 = allpass /IDX08 parametric eq1 slope 1 / 2 1 = 6dB, 2 = 12dB /IDX09 parametric eq1 frequency 20 to 20000 Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 699 20 to 20000 /IDX28 parametric eq6 gain -18 to 12 /IDX29 parametric eq6 quality 0.4 to 40 /IDX2A parametric eq7 bypass 0 / 1 0 = active, 1 = bypass Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 700 -12 to +12 20Hz /IDX46 graphic eq bypass band 0 / 1 0 = active, 1 = bypass 25Hz /IDX47 graphic eq gain band -12 to +12 25Hz Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 701 -12 to +12 200Hz /IDX5A graphic eq bypass band 0 / 1 0 = active, 1 = bypass 250Hz /IDX5B graphic eq gain band -12 to +12 250Hz Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 702 2kHz -12 to +12 /IDX6E graphic eq bypass band 0 / 1 0 = active, 1 = bypass 2.5kHz /IDX6F graphic eq gain band -12 to +12 2.5kHz Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 703 0 to 1000 default milliseconds, units can be appended (ms, samples, feet, inch, meter, cm, us, sec) /IDX84 input mute 0 / 1 0 = normal, 1 = muted Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 704 0 = peq, 1 = loshelv, 2 = hishelv, 3 = locut, 4 = hicut, 5 = allpass /IDX15 array peq 2 slope 1 / 2 1 = 6dB, 2 = 12dB /IDX16 array peq 2 frequency 20 to 20000 Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 705 0 = peq, 1 = loshelv, 2 = hishelv, 3 = locut, 4 = hicut, 5 = allpass /IDX33 speaker peq 2 slope 1 / 2 1 = 6dB, 2 = 12dB /IDX34 speaker peq 2 frequency 20 to 20000 Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 706 7 = s12q12, 8 = s12q15, 9 = s12q20, 10 = bessel12, 11 = butter12, 12 = linkwz12, 13 = bessel18, 14 = butter18, 15 = bessel24, 16 = butter24, 17 = linkwz24 Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 707 /IDX62 thermo limiter setting set of 12 values whitespace separated complete list of values in the order: r_vc c_vc r_m c_m z brms ctime atime rtime t_max t_wall t_knee Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 708: Updating The Firmware
The actual firmware file including version number is indicated and can be selected in the line “Firmware”. The IRIS-Net software package always includes the most up-to-date firmware version. The corresponding file is located in the directory: \IRIS-Net\Firmware\DX46 or \IRIS-Net\Firmware\DSP600. This path also appears in the line “Location”.
Page 709 The actual firmware file including version number is indicated and can be selected in the line “Factory Preset Bank”. The IRIS-Net software package always includes the most up-to-date factory presets version. The corresponding file is located in the directory: \IRIS-Net\Firmware\DX46 or \IRIS-Net\Firmware\DSP600. This path also appears in the line “Location”.
Page 710: Pws Programmable Wall Station
PWS Device Begin by creating a PWS device in your IRIS-Net project, by dragging a PWS from the Devices category into the Object List or from the Devices window over the Worksheet (see also chapter Devices and Menu Configurations). The following dialog appears: Bosch Security Systems B.V.
Page 711: Operation
Operation A previously configured wall station can be operated on-line as well as off-line under IRIS-Net. Double click on a PWS in the IRIS-Net worksheet to display the wall station’s front panel. All front panel controls can be operated using the mouse.
Page 712 Click on MODIFY FUNCTIONS / CONNECTIONS to set the assigned functionality/parameter of a control. Notes on how to edit function and connections of a control are provided in the chapter IRIS-Net > Editing Objects > Add Control Elements. HINT: Up to 12 connections can be assigned to a control.
Page 713 PWS-C CAN Bus coupler have to be identical and may exist only once on a specific CAN Bus. When adding new wall stations to an IRIS-Net project, CAN addresses are automatically allocated in ascending order.
Page 714: Button Types
BUTTON TYPE Action Button shows how to configure a PWS-6 to switch between presets in a conference room. Therefore, it is assumed that the IRIS-Net project includes a NetMax N8000 with three presets: MUSIC (U01, background music), SPEECH (U02, e.g. for presentations) and MUTE (U03). The three upper buttons of the PWS-6 shall be configured to switch between these three presets.
Page 715: Channel Selection
PWS-4 so that the Up/Down buttons can be used to individually control the volume setting for announcements and background music. Therefore, it is assumed that the IRIS-Net project includes a NetMax N8000 with a 2x1 monaural mixer. Announcements shall be fed to input 1 and the background music to input 2. The two upper buttons of the PWS- 4 are to be used to select the desired signal (i.e.
Page 716 The following example for the usage of the button type "Pushbutton" shows how to configure a button of a PWS-6 to serve as "Push-to-Talk button". Threrefore, it is assumed that the IRIS-Net project includes a NetMax N8000 with a 4 x 4 priority matrix and the signal of a microphone is being fed to input 1 of that matrix.
Page 717 BUTTON TYPE “Switch Button” shows how to configure the buttons of a PWS-6 to be able to select different sound reinforcement zones of a building. Therefore, it is assumed that the IRIS-Net project includes a NetMax N8000 equipped with an AO-1 Analog Output Card, with the card’s outputs 1 to 3 representing the different areas in a building.
Page 718 Repeat steps 4 to 9 for Button 2 (label "ROOM 2", connection "N8000_1.DSP.AnalogOut_1.Ch2") and Button 3 (label "ROOM 3", connection "N8000_1.DSP.AnalogOut_1.Ch3"). The following illustration shows the Configuration Dialog after configuration of the third button is finished. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 719: Promatrix 8000
IRIS-Net PROMATRIX 8000 | en PROMATRIX 8000 Please note the following when using project files in different versions of IRIS-Net. “old” IRIS-Net version “new” IRIS-Net version Updates The Task Engine of the DPM 8016 has changed, updating all Task Engine blocks is necessary.
Page 720 No updates of project file necessary. 3.1.2 3.1.3 No updates of project file necessary. 3.1.3 3.1.4 No updates of project file necessary. 3.1.4 3.2.0 No updates of project file necessary. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 721 Relay modules, in total (DCS 408 or n * 255 DCS 409) Number of relays, in total 2000 n * 2000 Task Engine blocks 1024 n * 1024 Task Engine connections per block Network channels Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 722: Dpm 8016 Paging Manager
DPM 8016 Device Start by creating an DPM 8016 Device in your IRIS-Net project. Drag an DPM 8016 from the Object Bar’s Devices category or from the Devices window into the worksheet (see also chapters: Devices and Configurations menu). The following dialog box appears: Bosch Security Systems B.V.
Page 723 Additional configuration windows can be navigated to by clicking on the icons at the top of the window. However, as a basic rule, IRIS-Net will remember which window was used last and reopen to this window next time you double click on the device icon.
Page 724 System language Korean or Chinese For using system languages Korean or Chinese the call station firmware type “CST_Vx.x.xA” has to be used. Please be patient when uploading this firmware to the call station. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 725 MAC address of the DPM 8016 is also shown on a label on the unit’s rear panel. NAME IRIS-Net internal device name of the DPM 8016. BUZZER Select ON to indicate a connection failure to a call station (selectable via the drop down field) via the integrated buzzer of the DPM 8016.
Page 726 Press the change button to edit the setting of the password for going online LEVEL 3) in IRIS-Net. FIRMWARE UPDATE PASSWORD Press the change button to edit the setting of the password for updating the (ACCESS LEVEL 4) firmware of the system. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 727 LED on the front panel of the DPM lights, the FAULT relay opens and a signal sound. Detected types of errors for which the checkbox HOLD is ticked are stored. Sporadic errors are indicated until the corresponding HOLD checkbox is unchecked. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 728 Watchdog error of the DPM. This error type is logged conforming to standards, press the CLEAR button to reset the error. FIRMWARE The DPM firmware version is not compatible with the IRIS-Net version used. A firmware update is recommended. MODULES Invalid module configuration of the DPM 8016.
Page 729 Fault condition on the PCA bus. Further details are provided in the Interface dialog. The parameter %u gives the slot number of the erroneous module. AUDIO NET Fault condition on the audio network. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 730 Manually setting or resetting an error. DSP Dialog In this dialog the DSP configuration of the DPM 8016 is shown. Double clicking on a DSP-Block’s icon allows editing its configuration and settings in detail. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 731 Double click the block to open the Input dialog. Select the entry Advanced Control from the context menu of the block to open the Advanced Control dialog. Bosch Security Systems B.V. User Manual...
Page 732 INV button for inverting the input signal’s polarity. Text field for labeling an input channel, e.g. giving it an application specific name. CAUTION: Using * (asterisk) and/or = (equal) signs in a name is not permissible. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 733 Description The unique name or description of the uploaded message. Use the corresponding text field to edit the description. The description can be edited in offline or online mode. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 734 Select the default chime or pre-chime signal to use if no chime is uploaded to the MM-2 module. Chime This settings is valid for all DPM 8016 in the PROMATRIX system. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 735 Equalizers accentuate or lower the audio signal within specific frequency ranges. Two parametric 3- Band equalizers are available for each UI-1 Universal Input Module or MM-2 Message Manager Module. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 736 0 dB -18 to +18 dB GAIN defines the amplification (increase) or attenuation (reduction) of parametric EQs or low shelving and high shelving equalizers. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 737 Compressor sets in. Entering the desired value is 3.085 V 0.275 to 8.696 V possible in dBu as well as in V. The entered value is automatically converted in both directions. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 738 Compressor (engaged), which allows for quick A / B comparison between the com- pressed and uncompressed audio signal. DELAY The Delay block allows to delay the audio signal of AO-1 output modules by up to 220 ms. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 739 5 BAND PEQ Equalizers accentuate or lower the audio signal within specific frequency ranges. Two parametric 5- Band equalizers are available for each AO-1 Analog Output Module. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 740 0 dB -18 to +18 dB GAIN defines the amplification (increase) or attenuation (reduction) of parametric EQs or low shelving and high shelving equalizers. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 741 BYPASS switches the corresponding filter ON (not engaged) or OFF (engaged), which allows for quick A / B-evaluation of the actual effect that a filter has on the sound. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 742 BYPASS activates (not engaged) or deactivates (engaged) the Limiter, which allows for quick A / B comparison between the limited and unlimited audio signal. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 743 The PLT button appears only when the pilot tone generator has previously been activated in the Advanced Control window. MUTE button for muting the output signal. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 744 The Alarm Chime dialog allows the configuration of the internal alarm and chime generators. Element Default Range Description Alarm Configuration -3.0 dB -80 to 0 dB Fader for setting the alarm level. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 745 Inputs used for alarms, announcements etc. can not be routed – Inputs used for a MM-2 Message Module can not be routed – Manual routings override existing BGM routings – Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 746 Configuring the Task Engine as well as wiring DSP blocks is possible only in offline mode. Please refer to section “How to configure a Control” on page 20 how to assign functions and connections to a Task Engine block. Bosch Security Systems B.V. User Manual...
Page 747 (alarm, announcement, message, etcetera) is overwritten by a conflicting existing paging with higher priority. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 748 The current value at the input is assigned to the connection. HINT: Initialization and updating of Remote Boolean Values depends on the connection to the remote DPM 8016. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 749 The Greater block compares the rational numbers at the inputs. The Boolean value at the output is only true when the rational number of the upper input is greater than the rational number of the lower input. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 750 The Convert block converts a rational number to a Boolean value. The rational number 0.0 is converted to the Boolean value 0, the rational number 1.0 is converted to the Boolean value 1. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 751 INPUT CHANNEL: When using ALARM = EXTERN select the input channel of the DPM 8016, where the external alarm signal is present. – DESTINATIONS: Select the destination zone(s) or group(s) for the alarm. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 752 INPUT CHANNEL: When using ALARM = EXTERN select the input channel of the device, where the external alarm signal is present. – DESTINATIONS: Select the destination zone(s) or group(s) for the alarm. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 753 – INPUT CHANNEL: Select the input channel of the device, where the announcement signal is present. – DESTINATIONS: Select the destination zone(s) or group(s) for the announcement. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 754 LOOP: Select this checkbox to repeat the chime automatically. – HOLD: Hold means that the message is stopped at the loop end. – DESTINATIONS: Select the destination zone(s) or group(s) for the chime. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 755 LOOP: Select this checkbox to repeat the message automatically. – HOLD: Hold means that the message is stopped at the loop end. – DESTINATIONS: Select the destination zone(s) or group(s) for the message. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 756 Hold: See illustration below. – Retrigger Falling: See illustration below. – Retrigger Rising: See illustration below. – State: State of the block (1 = time running) – Timer Value Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 757 The Text Box allows labeling the task engine configuration. Click the Modify Properties entry in the context menu to open the Edit Textbox dialog. This dialog allows editing the caption and e.g. font size and font type. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 758 Ok range. The USER FAULT is set to 1 if the rational number at the input is below or above the Ok range. Following properties are used to select the USER FAULT: – userfault_connection – userfault_idx Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 759 Superblocks Superblocks are listed here. Please refer to page 240 how to use Superblocks. Alarm Types Type Graphical Illustration Extern DIN Alarm Slow Whoop Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 760 Ship Alarm 1 Ship Alarm 2 Ship Alarm 3 Ship Alarm 4 Ship Alarm 5 Ship Alarm 6 Ship Alarm 7 Ship Alarm 8 Ship Alarm 9 Ship Alarm 10 Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 761 Ship Alarm 16 Ship Alarm 17 SILENCE Chime types 1_TONE 2_TONE 3_TONE 4_TONE 2x2_TONE 2_TONE_PRE Characters for CST Text block Available characters for text messages at DPC 8015 display " & Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 762 IRIS-Net PROMATRIX 8000 | en < “space” Pagings Dialog The paging dialog allows the configuration of pagings (e.g. alarm or EVAC message) with dynamic or static destinations. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 763 The value used to trigger the stop of (or subtraction of destinations from) an active paging. The rising edge of the value is evaluated. PAGING The paging initiated by the condition. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 764 Select IMMEDIATE if the paging should stop immediately or the zones should be removed immediately. TRIGGERED Select TRIGGERED if the paging should be triggered by the value selected below. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 765 Keywords in condition list Keywords can be selected from the condition list to start a signal: Pagings.VCondition%d.Value where %d is replaced with an ongoing decimal number. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 766 Button LED, even if there is no signal running due to the empty zone pattern. The Call Station buzzer will not beep. See also – Pagings Dialog, page 765 – Pagings Dialog, page 766 Programs Dialog The Programs dialog allows to configure 16 programs for back ground music. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 767 Edit the priority of the program selected in the program list (range: 1 to 69). LEVEL (dB) Edit the level of the program selected in the program list (range: -80 to 0 dB). Only the level can be edited in online mode. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 768 The condition that starts the background music, e.g. a switch connected to a GPI of the device. INVERT Set the checkbox to invert the condition that starts the back ground music. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 769 The Interface window allows configuring the different interfaces located on the rear panel of the DPM 8016. All REMOTE CAN BUS and DPM 8016 CONTROL PORT settings can be made in here. Configuring the Ethernet interface is done under Network Settings in the General window. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 770 PASSWORD field. Go online (write) to set the password in the DPM. HINT: Editing the password setting is possible in offline mode only. TCP Port TCP port of the ASCII control protocol. The default port is 6273. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 771 When selecting the checkbox “ENABLE” a specific topology with 100 zones is created automatically. Please take care to start with this topology, as then the first 100 zones are reserved for the Promatrix 4000 system. Existing zones may be deleted. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 772 Select the GPO contact or the virtual TE value for signaling the DPM operating mode. In standby mode the GPO is open. EXTERNAL ON/STANDBY Select the digital GPI or virtual TE value to be used for switching to standby mode. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 773 HINT: The “Power Calculator” tool can be used to calculate the power consumption of a DPM 8016 or a complete PROMATRIX 8000 system. The tool can be found in directory “/Tools” or can be requested from the IRIS-Net support team.
Page 774 Usage of EOL 8001 modules is only possible if direct topology is used. LINE SUPERVISION TABLE Element Description ZONE/LINE System internal description of the zone or line. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 775 EXPORT All measurement data of the LINE SUPERVISION TABLE are exported to a csv file. Open the file in a spreadsheet for further processing. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 776 Topology/Zones Dialog The Topology/Zones dialog window allows configuration of Topologies and Zones. Zones are configured in a topology, each zone can be selected to be member of a Group. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 777 Click on this button to create a new Group. The All group, including all zones, is created automatically. For every new group the zones can be selected via the checkboxes in the group column. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 778 Select the input source of the amplifier channel. This Combo box lists all output channels of AO-1 modules of the DPM 8016. There is a combo box for each channel of the amplifier (1, 2 or 4). Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 779 In this case the relays have to be assigned manually. Select the output channel of the amplifier to be used as input for this topology. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 780 In this case the relays have to be assigned manually. IN A or B Select the output channel of the amplifier to be used as input for part A or B of this topology Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 781 This combo box lists all type of topologies that can be created in the Promatrix 8000 system. Number Of Zones Number of zones to be created in the selected topology. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 782 This combo box lists all available relays of DCS or DPA devices in the PROMATRIX 8000 system. Enter a name for the zone. This control allows setting the priority value of a priority relay. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 783 Select the output channel of the amplifier to be used as input for the call line of this topology IN (Prog) Select the output channel of the amplifier to be used as input for the program line of this topology Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 784 This dialog allows to create, edit or delete groups. It is also possible to add or remove zones from a selected Group. To remove a zone from a group, select the zone in the GROUP MEMBERS section and press the delete button. Bosch Security Systems B.V. User Manual...
Page 785 In case of failure of the Ethernet AudioNet Redundancy is enabled. This function allows transmitting a signal in a predefined zone pattern to all DPMs, if the function is activated and a Destination is defined. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 786 COLLECTED ERROR AUDIO NET flag is set at the same time. The current condition of each type of error gets indicated. Green means no error, red indicates that an error has been detected. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 787 The number of devices connected to the audio network (Ethernet) is not COMPLETE identical to the number of configured devices. COLLECTED This error is indicated as “AUDIO NET” error in the Supervision dialog. ERROR AUDIO NET Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 788 To connect an external device to the Controller via Ethernet, the Ethernet port of the Controller must be configured. Following table lists the keywords of the Controller for Ethernet configuration. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 789 Description Idx.y Unique identifier: x is the number x in the IRIS-Net internal device name, e.g. „Device_x“ y is a unique paging request number of the local Controller Change ON, if the paging request Idx.y has activated one or more local audio outputs of the Controller...
Page 790 For assigning a Boolean value via the ASCII Control Protocol the Task Engine block type „Input Logic“ is used. The value of the block‘s property function must be set to <LVal><id>. The value of the block‘s property connection must be set to DPM8016_x.OpenInterface Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 791 Analog values Following format is used to query the value of a analog value: <AVal><id> ? Element Description AVal Indicates the use of a analog value in the Task Engine Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 792 Fault group 17:1 DATA „DPM Data fault“ asserted WATCHDOG INT-2 Fault INT-2#1 1 Fault group 3 asserted „Watchdog fault“ FIRMWARE INT-3 Fault INT-3#1 1 Fault group 18 asserted „DPM software fault“ Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 793 Line-Nr. of EXT-5 Line-Nr. of Fault EXT-5#100 1 Fault group 16:100 FAULT faulty line faulty line „Line fault:#100“ asserted with 1 to 500: Zone A, 501 to 1000: Zone B Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 794 USER FAULT 9 User defined USR-9 User defined Fault USR-9#17 1 Fault group 28:17 “User fault 9:#17” asserted USER FAULT User defined USR-1 User defined Fault USR-10#17 Fault group 29:17 1 “User fault asserted 10:#17” Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 795: Dpc 8000 Call Station
DPC 8015 Device Start by creating an DPC 8016 Device in your IRIS-Net project. Drag a DPC 8015 from the Object Bar’s Devices category or from the Devices window into the worksheet (see also chapters: Devices and Configurations menu). The following dialog box appears: Bosch Security Systems B.V.
Page 796 Additional configuration windows can be navigated to by clicking on the icons at the top of the window. However, as a basic rule, IRIS-Net will remember which window was used last and reopen to this window next time you double click on the Call Station device icon.
Page 797 When there are several DPM 8016 in the project or there are several call stations connected to a single UI-1 Universal Input Module you can select the call station (kit) to configure here. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 798 1 to 16. The entered value is adopted by pressing RETURN. The entered address has to match the setting in the call station's menu and may only exist once on the CAN-Bus. When adding new call stations to an IRIS-Net project, CAN addresses are automatically assigned in ascending order.
Page 799 When pressing this button, the backlight of the call station's LCD screen blinks regularly in quick succession. The status indicator of the call station Device in IRIS-Net blinks at the same time. This function serves for checking communication and for identification or search of a call station in a larger system.
Page 800 Clicking onto the button „..." opens the Destinations Dialog for selecting desired Zones and/or Groups. Clear Key A switch of the type "Clear Key" allows configuring an ALL/CLEAR button. Pressing the button on the call station selects or deselects all Zones and/or Groups. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 801 LED only = indicates the value of the logic variable, the value is not changed by the button Select the LED of the button that should indicate the value „1“ of the logic variable: – Primary LED (green/red) – Secondary LED (yellow) – None Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 802 Active Selecting this checkbox allows the user to press the button even though the call station has been locked. when locked Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 803 Stop Signal Chime Pressing the button on the call station stops chimes. Stop Signal Alarm Pressing the button on the call station stops alarms. Stop Signal Text Pressing the button on the call station stops signal texts. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 804 Ship Alarm 9 – Ship Alarm 10 – Ship Alarm 11 – Ship Alarm 13 – Ship Alarm 14 – Ship Alarm 15 – Ship Alarm 16 – Ship Alarm 17 Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 805 Selecting this checkbox allows the user to press the button even though the call station has been locked locked. On Key A switch of the type “On” allows switching the PROMATRIX 8000 system on or off (standby) using a button of the call station. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 806 EVAC ore Business Message from the Message Manager. Element Description Destination Clicking onto the button „..." opens the Destinations Dialog for selecting desired Zones and/or Groups. Priority Select the priority (0 to 100) of the message. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 807 Selecting this checkbox allow the user to press the button even though the call station has been locked. Diagnostics The diagnostics dialog is used for supervision of the call station. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 808 Watchdog error in DPC. This error type is logged according standards, press the CLEAR button to reset the error. FIRMWARE The firmware version of the DPC is to old. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 809 Supervision fault of the alarm button or the key switch. POWER SUPPLY Power supply out of range. COLLECTED ERROR STATE: The FAULT-LED at the call station lights at the occurrence of this type of error. DPC DEVICE Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 810: Pmx-Csk Call Station Kit
Internal supervision with event log - fulfills all requirements of relevant national and international standards PMX-CSK Device Start by creating an PMX-CSK Device in your IRIS-Net project. Drag an PMX-CSK from the Object Bar’s Devices category or from the Devices window into the worksheet (see also chapters: Devices and Configurations menu). The following dialog box appears: Bosch Security Systems B.V.
Page 811 Additional configuration windows can be navigated to by clicking on the icons at the top of the window. However, as a basic rule, IRIS-Net will remember which window was used last and reopen to this window next time you double click on the PMX-CSK device icon.
Page 812 Element Description This paragraph provides explanation of how to select the proper call station for configuration, when several call stations are connected to a single UI-1 Universal Input Module. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 813 DIP switch S22 on the call station kit and may only exist once on the CAN- Bus. When adding new call stations to an IRIS-Net project, CAN addresses are automatically assigned in ascending order.
Page 814 When pressing this button, the backlight of the call station's LCD screen blinks regularly in quick succession. The status indicator of the call station Device in IRIS-Net blinks at the same time. This function serves for checking communication and for identification or search of a call station in a larger system.
Page 815 Watchdog error in CSK. This error type is logged according standards, press the button connected to ESC_K to reset the error. FIRMWARE The firmware version of the CSK is to old. MICROPHONE Microphone error in CSK. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 816 Supervision fault of the alarm button or the key switch. POWER SUPPLY Power supply out of range. COLLECTED ERROR: The FAULT-LED at the call station lights at the occurrence of this type of error. DPC DEVICE Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 817: Dpa 8000 Power Amplifier
REMOTE CAN BUS. The amplifiers have been designed for use in an evacuation system. Control usually is taken care of by the DPM 8016 Paging Manager and the configuration by means of IRIS-Net. If amplifiers are operated without employing a DPM 8016, the configuration can be created in IRIS-Net and permanently be stored in the amplifier, so that the desired state (preset) is activated, each time the device is powered ON.
Page 818: Control Panel
Keep the mouse button pressed while dragging the panel. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 819 Using the left mouse button, click in the entry field and enter the desired name for the channel. Press Return on the key- board to acknowledge your entry. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 820 Clicking this switch activates the STATUS indicator on the amplifier’s rear panel as well as in the amplifier’s front panel window in the IRIS-Net software. Normally, the STATUS indicator blinks only during serial communication. Once the STATUS switch is engaged, the STATUS indicator blinks in a steady but fast sequence.
Page 821 Element Description MODEL Shows the amplifier type NAME IRIS-Net internal name of the amplifier FIRMWARE Shows the amplifier‘s software version number (operating system, firmware) Opens the firmware update dialog. PRV / DIR / AEC For each amplifier output channel the signal of the direct input (DIR), the AEC input (AEC) or the previous input (PREV) can be selected.
Page 822 The text field allows specifying a name for the corresponding output channel. The output voltage of the output channel can be set to 50, 70 or 100 Volts. The configuration in IRIS-Net must be identical to the hardware configuration of the amplifier, please refer to the owner‘s manual for details.
Page 823 Additionally the ready relays changes to „not operational“ state. DEVICE LOST The CAN bus connection between DPM and DPA is broken. AMPLIFIER MODEL Amplifier type in IRIS-Net and actually connected hardware do not match. MEMORY/DATA Memory or Read/Write error. Bosch Security Systems B.V.
Page 824 COLLECTED ERROR The FAULT LED at the DPA front panel lights at the occurrence of this type of error. STATE Press this button to activate the COLLECTED ERROR STATE manually. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 825: Dcs Digital Control System
DCS Device First of all, create a new DCS device in your IRIS-Net project by dragging a DCS with the desired number of height units (HU) from the Object List's Devices category or out of the Devices Window into the worksheet (please also refer to the chapter "Configuration of Devices and Menus").
Page 826 Double clicking on a DCS Device opens the configuration dialog box. Configuration dialog Double clicking on a DCS Device in the IRIS-Net worksheet opens the Configuration Dialog box which allows making all the settings that are necessary for starting up the DCS system.
Page 827 – Frame 1: Slot 1 always has to be equipped with a DCS 801R. IRIS-Net automatically adds a DCS 801R. Rearranging or deleting the DCS 801R is not possible. If the DCS system consists of only one frame, slots 2 to 10 can be equipped with the following card types: DCS 408R, DCS 409R, DCS 412R, DCS 416R, DCS 406R.
Page 828 DCS 801R is equipped with exceeds the maximum number of modules that a DCS-400 rack can host. Element Description Name of the module CAUTION: Using * (asterisk) and/or = (equal) signs in a name is not permissible. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 829 It can also be used to provide switching contacts when higher voltages and/or currents exist. Element Description Name of the module CAUTION: Using * (asterisk) and/or = (equal) signs in a name is not permissible. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 830 State of the relay in error condition. Detailed information about the "error condition" of a DCS system is provided in the description of the DCS 801R module. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 831 PROMATRIX 8000 | en DCS 412R LOGIK INPUT MODULE The DCS 412R module is used for connecting control lines, buttons, switches, and sensors to be able to evaluate their statuses (on, off) in the IRIS-Net system. Element Description Name of the module CAUTION: Using * (asterisk) and/or = (equal) signs in a name is not permissible.
Page 832 The Supervision dialog is used for supervision of the DCS. You have the option to choose, which errors are combined and indicated in a general fault message. HINT: This Supervision dialog is only available when the DCS is connected to a DPM 8016. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 833 The firmware version of the DCS is not compatible with the DPM firmware version. A firmware update is recommended. DCS MODULES The module configuration of the DCS in IRIS-Net does not match the actual module configuration. POWER SUPPLY Supply voltage out of range.
Page 834: Promatrix 6000
IRIS-Net PROMATRIX 6000 | en PROMATRIX 6000 Please note the following when using project files in different versions of IRIS-Net. “old” IRIS-Net version “new” IRIS-Net version Updates 3.0.0 3.0.1 No updates of project file necessary. 3.0.1 3.1.0 No updates of project file necessary.
Page 835 Additional configuration windows can be navigated to by clicking on the icons at the top of the window. However, as a basic rule, IRIS-Net will remember which window was used last and reopen to this window next time you double click on the device icon.
Page 836 System language Korean or Chinese For using system languages Korean or Chinese the call station firmware type “CST_Vx.x.xA” has to be used. Please be patient when uploading this firmware to the call station. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 837 MAC address of the PMX-4CR12 is also shown on a label on the unit’s rear panel. NAME IRIS-Net internal device name of the PMX-4CR12. BUZZER Select ON to indicate a connection failure to a call station (selectable via the drop down field) via the integrated buzzer of the PMX-4CR12.
Page 838 Press the change button to edit the setting of the password for going online LEVEL 3) in IRIS-Net. FIRMWARE UPDATE PASSWORD Press the change button to edit the setting of the password for updating the (ACCESS LEVEL 4) firmware of the system. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 839 LED on the front panel of the device lights, the FAULT relay opens and a signal sound. HOLD Detected types of errors for which the checkbox HOLD is ticked are stored. Sporadic errors are indicated until the corresponding HOLD checkbox is unchecked. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 840 Watchdog error of the device. This error type is logged conforming to standards, press the CLEAR button to reset the error. FIRMWARE The device firmware version is not compatible with the IRIS-Net version used. A firmware update is recommended. HARDWARE Error in the power supply or the A/D converters of the device.
Page 841 Active if any system fault is active in the system. “ALL" switch button control can be used to activate system-wide collection for this fault on the controller. SYSTEM COMBINED FAULT Active if any COMBINED FAULT STATE is active in the system. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 842 The number must always be “2”. 0.0 dB 0 to 60 dB The gain of the MIC/LINE input channels can be adjusted in 6 dB steps. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 843 Indicates the level of the message. Level ranges from -80 dB to +18 dB. Default level is 0.0 dB. Use the corresponding spin control to edit the level. The level can be edited in offline or online mode. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 844 HINT: For creating audio messages the software Audacity from http://audacity.sourceforge.net/ can be used. 3 BAND PEQ Equalizers accentuate or lower the audio signal within specific frequency ranges. Eight parametric 3-Band equalizers are available. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 845 BYPASS switches the corresponding filter ON (not engaged) or OFF (engaged), which allows for quick A / B-evaluation of the actual effect that a filter has on the sound. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 846 Element Default Range Description OUT 1-4 Press the output channel button to view or edit the corresponding Parametric EQ settings. Pressing BYPASS ALL switches of all filters. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 847 Element Default Range Description OUT 1-4 Press the output channel button to view or edit the corresponding Peak Limiter settings. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 848 MUTE button for muting the output signal. ALARM CHIME The Alarm Chime dialog allows the configuration of the internal alarm and chime generators. Element Default Range Description Alarm Configuration Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 849 0.01 to 0.4 FADE OUT defines how fast the gain of the background music signal is returned to the preset level once the input signal drops below the threshold level. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 850 (alarm, announcement, message, etcetera) is overwritten by a conflicting existing paging with higher priority. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 851 Engine configuration. The Calendar Entry block is being used to create time-dependant Boolean values. The outputted Boolean value depends on the configuration of this block and the current system time. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 852 TE.RANGE_CHECK_1.range.min and lower or equal than the property TE.RANGE_CHECK_1.range.max – range.max: Enter the upper bound of the range to be checked – range.min: Enter the lower bound of the range to be checked Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 853 The Not Equal block compares the Boolean values at the inputs. The Boolean value at the output is only true when the values at the inputs are different from each other (e.g. one input is true while the other input is false). Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 854 INPUT CHANNEL: When using ALARM = EXTERN select the input channel of the DPM 8016, where the external alarm signal is present. – DESTINATIONS: Select the destination zone(s) or group(s) for the alarm. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 855 INPUT CHANNEL: When using ALARM = EXTERN select the input channel of the device, where the external alarm signal is present. – DESTINATIONS: Select the destination zone(s) or group(s) for the alarm. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 856 – INPUT CHANNEL: Select the input channel of the device, where the announcement signal is present. – DESTINATIONS: Select the destination zone(s) or group(s) for the announcement. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 857 LOOP: Select this checkbox to repeat the chime automatically. – HOLD: Hold means that the message is stopped at the loop end. – DESTINATIONS: Select the destination zone(s) or group(s) for the chime. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 858 LOOP: Select this checkbox to repeat the message automatically. – HOLD: Hold means that the message is stopped at the loop end. – DESTINATIONS: Select the destination zone(s) or group(s) for the message. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 859 Hold: See illustration below. – Retrigger Falling: See illustration below. – Retrigger Rising: See illustration below. – State: State of the block (1 = time running) – Timer Value Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 860 The Text Box allows labeling the task engine configuration. Click the Modify Properties entry in the context menu to open the Edit Textbox dialog. This dialog allows editing the caption and e.g. font size and font type. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 861 Ok range. The USER FAULT is set to 1 if the rational number at the input is below or above the Ok range. Following properties are used to select the USER FAULT: – userfault_connection – userfault_idx Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 862 Superblocks Superblocks are listed here. Please refer to page 240 how to use Superblocks. Chime types 1_TONE 2_TONE 3_TONE 4_TONE 2x2_TONE 2_TONE_PRE Alarm Types Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 863 DIN Alarm Slow Whoop Siren Two-Tone Alarm Telephone Alarm Ship Alarm 1 Ship Alarm 2 Ship Alarm 3 Ship Alarm 4 Ship Alarm 5 Ship Alarm 6 Ship Alarm 7 Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 864 Ship Alarm 15 Ship Alarm 16 Ship Alarm 17 SILENCE Pagings Dialog This dialog allows the configuration of pagings (e.g. alarm or EVAC messages) with dynamic or static destinations. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 865 The value used to trigger the stop of (or subtraction of destinations from) an active paging. The rising edge of the value is evaluated. PAGING The paging initiated by the condition. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 866 Select NEXT SEQUENCE if zones should be removed only after the message ended. When selected, the paging is stopped immediately after the message ended. Can only be used for MM-2 Messages. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 867 See also – Configuration Dialog, page 898 – Pagings Dialog, page 765 – Pagings Dialog, page 766 Programs Dialog The Programs dialog allows to configure 4 programs for background music. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 868 Edit the priority of the program selected in the program list (range: 1 to 69). LEVEL (dB) Edit the level of the program selected in the program list (range: -80 to 0 dB). Only the level can be edited in online mode. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 869 CALL STATIONS Select the call stations where the selected program will be listed in the menu. UserMix Dialog This dialog allows configuring audio routings (e.g. background music) in the system. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 870 The Interface window allows configuring the different interfaces located on the rear panel of the device. All REMOTE CAN BUS and CONTROL PORT settings can be made in here. Configuring the Ethernet interface is done under Network Settings in the General window. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 871 TCP port of the ASCII control protocol. The default port is 6273. NUMBER OF LOGIC VALUES Enter the number of logic values of the task engine to be available via the ASCII control protocol. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 872 It is possible to manually change the condition of the control outputs (normally open contact / normally closed contact). PowerManagement Dialog The Power Management dialog allows configuring the standby mode of the device in detail. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 873 PERIPHERAL DEVICE STATUS Set the checkbox to monitor the status of peripheral devices.. COMBINED POWER STATE This LED is green, if all selected power supply status are OK. SYSTEM OPERATION MODE & CST TEXT Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 874 Notice! The “Power Calculator” tool can be used to calculate the power consumption of the system. The tool can be found in directory “/Tools” or can be requested from the IRIS-Net support team. Notice! The properties “Operating Mode” and “Standby LED” can be used for advanced power management configuration via the Task Engine, please refer to section Properties, page 788.
Page 875 HINT: If the zone is connected via a line relay, the relay will be deactivated when there is a short cut (short cut protection for other lines on the same amplifier). EOL FAULT This LED lights red, if a EOL error has occurred. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 876 The Line Supervision table is automatically generated from the available zones filled with default values. Notice! Use copy & paste to copy configurations from one element to another element in the line supervision table. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 877 The Topology/Zones dialog window allows configuration of Topologies and Zones. Zones are configured in a topology, each zone can be selected to be member of a Group. IRIS-Net offers basic validation checks if the connections are valid. If a rule is not followed correctly, the connection line turns red.
Page 878 If a 2-in-N or Program/Call topology is selected and the amplifier should be backed up by a spare amplifier, two spare amplifier channels are required. It is not allowed to backup both channels of the topology with one spare amplifier channel only. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 879 This dialog allows to create, edit or delete groups. It is also possible to add or remove zones from a selected Group. To remove a zone from a group, select the zone in the GROUP MEMBERS section and press the delete button. Bosch Security Systems B.V. User Manual...
Page 880 PMX-4CR12 and connected devices. High priority signals prevent changing into standby mode. Following settings are available: Value Description Switch PMX-4CR12 in standby mode Switch PMX-4CR12 in operating mode HINT: The mode of peripheral devices connected to the PMX-4CR12 is set automatically. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 881 In case of failure of the Ethernet, AudioNet Redundancy is enabled. This function allows transmitting a signal in a predefined zone pattern to all PMX-4CR12 controllers, if the function is activated and a Destination is defined. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 882 TRANSMIT REDUNDANCY CALLS ENABLE Enable/Disable transmission of redundancy calls. The highest prioritized call above or equal the VAC priority will be transmitted as redundancy call. Activated by default. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 883 SWITCH FAULT 2 User-selectable Supervised or Isolated GPIs for network Switch supervision. COLLECTED ERROR This error is indicated as “AUDIO NET” error in the Supervision dialog. Show Network details Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 884 MAC address of the OM-1 module. IP ADDRESS IP- address of the OM-1 module. PRIMARY/SECONDARY OPERATIONAL STATUS The physical port state; UP/DOWN. SPEED The link speed in Mbit/s. PRIORITY The priority of the port. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 885 HINT: Only one single Ethernet connection can be used at one time. HINT: The password protection of the ASCII Control Protocol can be configured at the Interfaces dialog of the Controller. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 886 Description Idx.y Unique identifier: x is the number x in the IRIS-Net internal device name, e.g. „Device_x“ y is a unique paging request number of the local Controller Change ON, if the paging request Idx.y has activated one or more local audio outputs of the Controller...
Page 887 Indicates the use of a analog value in the Task Engine Unique identifier of the analog value in the Task Engine Question mark Example: Query: “AVal 7” Response: “AVal7 -30.2222” Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 888: Pmx-4R24
Off: Zone in idle condition PMX-4R24 Device Start by creating a PMX-4R24 Device in your IRIS-Net project. Drag a PMX-4R24 from the Object Bar’s Devices category or from the Devices window into the worksheet (see also chapters: Devices and Configurations menu). The following dialog box appears: Bosch Security Systems B.V.
Page 889 Additional configuration windows can be navigated to by clicking on the icons at the top of the window. However, as a basic rule, IRIS-Net will remember which window was used last and reopen to this window next time you double click on the device icon.
Page 890 Description MODEL Indicates PMX-4R24, so you know the model of the device. NAME IRIS-Net internal device name of the Router. FIRMWARE Indicates the firmware version of the Router when on-line. Opens the firmware update dialog. NOTE: The default password for the firmware update is “0000”.
Page 891 Element Description STATE The current condition of each type of error gets indicated. Green means no error, red indicates that an error has been detected. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 892 Watchdog error of the device. This error type is logged conforming to standards, press the CLEAR button to reset the error. FIRMWARE The firmware version is not compatible with the IRIS-Net version used. A firmware update is recommended. POWER SUPPLY Error in the power supply of the device.
Page 893: Pmx-15Cst
The settings option for Voice Alarm (EN54-16) for a Controller is no longer available. PMX-15CST Device Start by creating a PMX-15CST device in your IRIS-Net project. Drag a PMX-15CST from the Object Bar’s Devices category or from the Devices window into the worksheet (see also chapters: Devices and Configurations menu). The following dialog box appears: Select the call station bus the device is connected to.
Page 894 Additional configuration windows can be navigated to by clicking on the icons at the top of the window. However, as a basic rule, IRIS-Net will remember which window was used last and reopen to this window next time you double click on the Call Station device icon.
Page 895 When pressing this button, the backlight of the call station's LCD screen blinks regularly in quick succession. The status indicator of the call station Device in IRIS-Net blinks at the same time. This function serves for checking communication and for identification or search of a call station in a larger system.
Page 896 Pressing the button on the call station automatically selects the Zones and/or Groups in which the spoken message is being heard. Notice! Different behavior of the TALK button can be configured for locked or unlocked state. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 897 Selection A switch of the type "Selection" allows configuring a SELECT button. Pressing the button on the call station selects the Zones and/or Groups that have been configured here. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 898 A switch of the type "Logical Key" allows setting the value of a logic variable (0 or 1). Pressing the button on the call station sets the logic variable to the desired value. The adjacent LED is operated according to the resulting parameter. Bosch Security Systems B.V. User Manual...
Page 899 – Up = increases the value of the numerical variable – Down = decreases the value of the numerical variable Parameter The numerical variable whose value is being changed. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 900 Select Monitoring to open the Audio Monitoring dialog in the display of the call station. Stop Key A switch of the type "Stop" allows canceling a process that is currently running on the system. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 901 Trigger Type Select the desired functionality for a button on a call station; available are: – Push (pushbutton) – Toggle (switches between two states) – Trigger (triggers a function) Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 902 A switch of the type "Chime Key" allows the launch of a gong (chime) signal in the system. Element Description Destination Clicking onto the button „..." opens the Destinations Dialog for selecting desired Zones and/or Groups. Priority Select the chime priority (0 to 100). Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 903 EVAC Message Key or Business Message Key A switch of the type "EVAC Message Key" or “Business Message Key” allows starting a prerecorded message of type EVAC ore Business Message from the Message Manager. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 904 Push (pushbutton) – Toggle (switches between two states) Active when locked Selecting this checkbox allow the user to press the button even though the call station has been locked. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 905 Watchdog error in the Call Station. This error type is logged according standards, press the CLEAR button to reset the error. FIRMWARE The firmware version of the Call Station is too old. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 906: Pmx-Csk
PMX-2P500 Device Start by creating an PMX-2P500 device in your IRIS-Net project. Drag an PMX-2P500 from the Object Bar’s Devices category or from the Devices window into the worksheet (see also chapters: Devices and Configurations menu). The following dialog box appears: Bosch Security Systems B.V.
Page 907 Additional configuration windows can be navigated to by clicking on the icons at the top of the window. However, as a basic rule, IRIS-Net will remember which window was used last and reopen to this window next time you double click on the device icon.
Page 908 Description MODEL Indicates PMX-2P500, so you know the model of the device. NAME IRIS-Net internal device name of the Amplifier. FIRMWARE Indicates the firmware version of the Amplifier when on-line. Opens the firmware update dialog. NOTE: The default password for the firmware update is “0000”.
Page 909 Element Description STATE The current condition of each type of error gets indicated. Green means no error, red indicates that an error has been detected. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 910 Watchdog error of the device. This error type is logged conforming to standards, press the CLEAR button to reset the error. FIRMWARE The firmware version is not compatible with the IRIS-Net version used. A firmware update is recommended. PROTECT Protect mode of amplifier activated.
Page 911: Paviro
IRIS-Net PAVIRO | en PAVIRO Please note the following when using project files in different versions of IRIS-Net. “old” IRIS-Net version “new” IRIS-Net version Updates 3.0.0 3.0.1 No updates of project file necessary. 3.0.1 3.1.0 No updates of project file necessary.
Page 912 Additional configuration windows can be navigated to by clicking on the icons at the top of the window. However, as a basic rule, IRIS-Net will remember which window was used last and reopen to this window next time you double click on the device icon.
Page 913 System language Korean or Chinese For using system languages Korean or Chinese the call station firmware type “CST_Vx.x.xA” has to be used. Please be patient when uploading this firmware to the call station. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 914 MAC address of the PVA-4CR12 is also shown on a label on the unit’s rear panel. NAME IRIS-Net internal device name of the PVA-4CR12. BUZZER Select ON to indicate a connection failure to a call station (selectable via the drop down field) via the integrated buzzer of the PVA-4CR12.
Page 915 The Supervision window shows the condition of the PVA-4CR12. When on-line, all fault conditions are being indicated. It is possible to select for each type of error whether it is displayed in a collected fault message, buffered and/or indicated at the call station displays. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 916 LED on the front panel of the device lights, the FAULT relay opens and a signal sound. HOLD Detected types of errors for which the checkbox HOLD is ticked are stored. Sporadic errors are indicated until the corresponding HOLD checkbox is unchecked. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 917 Watchdog error of the device. This error type is logged conforming to standards, press the CLEAR button to reset the error. FIRMWARE The device firmware version is not compatible with the IRIS-Net version used. A firmware update is recommended. HARDWARE Error in the power supply or the A/D converters of the device.
Page 918 Manually setting or resetting an error. DSP Dialog In this dialog the DSP configuration of the Controller is shown. Double clicking on a DSP-Block’s icon allows editing its configuration and settings in detail. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 919 The gain of the MIC/LINE input channels can be adjusted in 6 dB steps. The +48V button of the MIC/LINE input channels is for activating phantom power whenever a suitable condenser microphone is being used. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 920 Indicates the level of the message. Level ranges from -80 dB to +18 dB. Default level is 0.0 dB. Use the corresponding spin control to edit the level. The level can be edited in offline or online mode. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 921 HINT: For creating audio messages the software Audacity from http://audacity.sourceforge.net/ can be used. 3 BAND PEQ Equalizers accentuate or lower the audio signal within specific frequency ranges. Eight parametric 3-Band equalizers are available. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 922 BYPASS switches the corresponding filter ON (not engaged) or OFF (engaged), which allows for quick A / B-evaluation of the actual effect that a filter has on the sound. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 923 Element Default Range Description OUT 1-4 Press the output channel button to view or edit the corresponding Parametric EQ settings. Pressing BYPASS ALL switches of all filters. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 924 Element Default Range Description OUT 1-4 Press the output channel button to view or edit the corresponding Peak Limiter settings. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 925 MUTE button for muting the output signal. ALARM CHIME The Alarm Chime dialog allows the configuration of the internal alarm and chime generators. Element Default Range Description Alarm Configuration Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 926 0.01 to 0.4 FADE OUT defines how fast the gain of the background music signal is returned to the preset level once the input signal drops below the threshold level. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 927 The Output Analog block is a variable parameter for rational numbers which always assigns the current value at the input to the connection. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 928 The Multiplication block multiplies the rational number of the upper input with the rational number of the lower input. The output always presents the result of this analog operation. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 929 (wired) inputs are true. The OR block provides 2 inputs for Boolean values. The Boolean value at the output is only true when at least one (wired) input is true. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 930 The Not Equal block compares the Boolean values at the inputs. The Boolean value at the output is only true when the values at the inputs are different from each other (e.g. one input is true while the other input is false). Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 931 INPUT CHANNEL: When using ALARM = EXTERN select the input channel of the DPM 8016, where the external alarm signal is present. – DESTINATIONS: Select the destination zone(s) or group(s) for the alarm. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 932 INPUT CHANNEL: When using ALARM = EXTERN select the input channel of the device, where the external alarm signal is present. – DESTINATIONS: Select the destination zone(s) or group(s) for the alarm. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 933 – INPUT CHANNEL: Select the input channel of the device, where the announcement signal is present. – DESTINATIONS: Select the destination zone(s) or group(s) for the announcement. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 934 LOOP: Select this checkbox to repeat the chime automatically. – HOLD: Hold means that the message is stopped at the loop end. – DESTINATIONS: Select the destination zone(s) or group(s) for the chime. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 935 LOOP: Select this checkbox to repeat the message automatically. – HOLD: Hold means that the message is stopped at the loop end. – DESTINATIONS: Select the destination zone(s) or group(s) for the message. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 936 Hold: See illustration below. – Retrigger Falling: See illustration below. – Retrigger Rising: See illustration below. – State: State of the block (1 = time running) – Timer Value Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 937 The Text Box allows labeling the task engine configuration. Click the Modify Properties entry in the context menu to open the Edit Textbox dialog. This dialog allows editing the caption and e.g. font size and font type. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 938 Ok range. The USER FAULT is set to 1 if the rational number at the input is below or above the Ok range. Following properties are used to select the USER FAULT: – userfault_connection – userfault_idx Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 939 Superblocks Superblocks are listed here. Please refer to page 240 how to use Superblocks. Chime types 1_TONE 2_TONE 3_TONE 4_TONE 2x2_TONE 2_TONE_PRE Alarm Types Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 940 DIN Alarm Slow Whoop Siren Two-Tone Alarm Telephone Alarm Ship Alarm 1 Ship Alarm 2 Ship Alarm 3 Ship Alarm 4 Ship Alarm 5 Ship Alarm 6 Ship Alarm 7 Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 941 Ship Alarm 15 Ship Alarm 16 Ship Alarm 17 SILENCE Pagings Dialog This dialog allows the configuration of pagings (e.g. alarm or EVAC messags) with dynamic or static destinations. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 942 The value used to trigger the stop of (or subtraction of destinations from) an active paging. The rising edge of the value is evaluated. PAGING The paging initiated by the condition. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 943 Select NEXT SEQUENCE if zones should be removed only after the message ended. When selected, the paging is stopped immediately after the message ended. Can only be used for MM-2 Messages. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 944 See also – Configuration Dialog, page 974 – Pagings Dialog, page 765 – Pagings Dialog, page 766 Programs Dialog The Programs dialog allows to configure 4 programs for background music. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 945 Edit the priority of the program selected in the program list (range: 1 to 69). LEVEL (dB) Edit the level of the program selected in the program list (range: -80 to 0 dB). Only the level can be edited in online mode. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 946 CALL STATIONS Select the call stations where the selected program will be listed in the menu. UserMix Dialog This dialog allows configuring audio routings (e.g. background music) in the system. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 947 The Interface window allows configuring the different interfaces located on the rear panel of the device. All REMOTE CAN BUS and CONTROL PORT settings can be made in here. Configuring the Ethernet interface is done under Network Settings in the General window. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 948 TCP port of the ASCII control protocol. The default port is 6273. NUMBER OF LOGIC VALUES Enter the number of logic values of the task engine to be available via the ASCII control protocol. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 949 It is possible to manually change the condition of the control outputs (normally open contact / normally closed contact). PowerManagement Dialog The Power Management dialog allows configuring the standby mode of the device in detail. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 950 PERIPHERAL DEVICE STATUS Set the checkbox to monitor the status of peripheral devices.. COMBINED POWER STATE This LED is green, if all selected power supply status are OK. SYSTEM OPERATION MODE & CST TEXT Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 951 Notice! The “Power Calculator” tool can be used to calculate the power consumption of the system. The tool can be found in directory “/Tools” or can be requested from the IRIS-Net support team. Notice! The properties “Operating Mode” and “Standby LED” can be used for advanced power management configuration via the Task Engine, please refer to section Properties.
Page 952 HINT: If the zone is connected via a line relay, the relay will be deactivated when there is a short cut (short cut protection for other lines on the same amplifier). EOL FAULT This LED lights red, if a EOL error has occurred. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 953 The Line Supervision table is automatically generated from the available zones filled with default values. Notice! Use copy & paste to copy configurations from one element to another element in the line supervision table. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 954 The Topology/Zones dialog window allows configuration of Topologies and Zones. Zones are configured in a topology, each zone can be selected to be member of a Group. IRIS-Net offers basic validation checks if the connections are valid. If a rule is not followed correctly, the connection line turns red.
Page 955 If a 2-in-N or Program/Call topology is selected and the amplifier should be backed up by a spare amplifier, two spare amplifier channels are required. It is not allowed to backup both channels of the topology with one spare amplifier channel only. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 956 This dialog allows to create, edit or delete groups. It is also possible to add or remove zones from a selected Group. To remove a zone from a group, select the zone in the GROUP MEMBERS section and press the delete button. Bosch Security Systems B.V. User Manual...
Page 957 The “PVACON_1.BuzzerControl” property of the PVA-4CR12 allows configuring the integrated buzzer. Following settings are available: Value Description Buzzer is activated is a new error appears. Buzzer is deactivated. CST_1 Buzzer is activated if the call station (CST_1, CST_2,...) is not connected. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 958 In case of failure of the Ethernet, AudioNet Redundancy is enabled. This function allows transmitting a signal in a predefined zone pattern to all PAVIRO controllers, if the function is activated and a Destination is defined. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 959 TRANSMIT REDUNDANCY CALLS ENABLE Enable/Disable transmission of redundancy calls. The highest prioritized call above or equal the VAC priority will be transmitted as redundancy call. Activated by default. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 960 SWITCH FAULT 2 User-selectable Supervised or Isolated GPIs for network Switch supervision. COLLECTED ERROR This error is indicated as “AUDIO NET” error in the Supervision dialog. Show Network details Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 961 MAC address of the OM-1 module. IP ADDRESS IP- address of the OM-1 module. PRIMARY/SECONDARY OPERATIONAL STATUS The physical port state; UP/DOWN. SPEED The link speed in Mbit/s. PRIORITY The priority of the port. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 962 Following table lists the default setting of the Controller’s Ethernet port. Parameter Default IP address 192.168.1.100 Network mask 255.255.255.0 Standard gateway 192.168.1.1 Port 6273 HINT: Only one single Ethernet connection can be used at one time. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 963 Description Idx.y Unique identifier: x is the number x in the IRIS-Net internal device name, e.g. „Device_x“ y is a unique paging request number of the local Controller Change ON, if the paging request Idx.y has activated one or more local audio outputs of the Controller...
Page 964 Description AVal Indicates the use of a analog value in the Task Engine Unique identifier of the analog value in the Task Engine Question mark Example: Query: “AVal 7” Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 965: Pva-4R24
Off: Zone in idle condition PVA-4R24 Device Start by creating a PVA-4R24 Device in your IRIS-Net project. Drag a PVA-4R24 from the Object Bar’s Devices category or from the Devices window into the worksheet (see also chapters: Devices and Configurations menu). The following dialog box appears: Bosch Security Systems B.V.
Page 966 Additional configuration windows can be navigated to by clicking on the icons at the top of the window. However, as a basic rule, IRIS-Net will remember which window was used last and reopen to this window next time you double click on the device icon.
Page 967 Element Description STATE The current condition of each type of error gets indicated. Green means no error, red indicates that an error has been detected. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 968 Watchdog error of the device. This error type is logged conforming to standards, press the CLEAR button to reset the error. FIRMWARE The firmware version is not compatible with the IRIS-Net version used. A firmware update is recommended. POWER SUPPLY Error in the power supply of the device.
Page 969: Pva-15Cst
– PVA-15CST Device Start by creating a PVA-15CST device in your IRIS-Net project. Drag a PVA-15CST from the Object Bar’s Devices category or from the Devices window into the worksheet (see also chapters: Devices and Configurations menu). The following dialog box appears: Select the call station bus the device is connected to.
Page 970 Additional configuration windows can be navigated to by clicking on the icons at the top of the window. However, as a basic rule, IRIS-Net will remember which window was used last and reopen to this window next time you double click on the Call Station device icon.
Page 971 When pressing this button, the backlight of the call station's LCD screen blinks regularly in quick succession. The status indicator of the call station Device in IRIS-Net blinks at the same time. This function serves for checking communication and for identification or search of a call station in a larger system.
Page 972 Pressing the button on the call station automatically selects the Zones and/or Groups in which the spoken message is being heard. Notice! Different behavior of the TALK button can be configured for locked or unlocked state. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 973 Selection A switch of the type "Selection" allows configuring a SELECT button. Pressing the button on the call station selects the Zones and/or Groups that have been configured here. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 974 A switch of the type "Logical Key" allows setting the value of a logic variable (0 or 1). Pressing the button on the call station sets the logic variable to the desired value. The adjacent LED is operated according to the resulting parameter. Bosch Security Systems B.V. User Manual...
Page 975 – Up = increases the value of the numerical variable – Down = decreases the value of the numerical variable Parameter The numerical variable whose value is being changed. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 976 Select Monitoring to open the Audio Monitoring dialog in the display of the call station. Stop Key A switch of the type "Stop" allows canceling a process that is currently running on the system. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 977 Trigger Type Select the desired functionality for a button on a call station; available are: – Push (pushbutton) – Toggle (switches between two states) – Trigger (triggers a function) Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 978 A switch of the type "Chime Key" allows the launch of a gong (chime) signal in the system. Element Description Destination Clicking onto the button „..." opens the Destinations Dialog for selecting desired Zones and/or Groups. Priority Select the chime priority (0 to 100). Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 979 EVAC Message Key or Business Message Key A switch of the type "EVAC Message Key" or “Business Message Key” allows starting a prerecorded message of type EVAC ore Business Message from the Message Manager. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 980 Push (pushbutton) – Toggle (switches between two states) Active when locked Selecting this checkbox allow the user to press the button even though the call station has been locked. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 981 Watchdog error in the Call Station. This error type is logged according standards, press the CLEAR button to reset the error. FIRMWARE The firmware version of the Call Station is too old. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 982: Pva-Csk
PVA-CSK Device Start by creating a PVA-CSK device in your IRIS-Net project. Drag a PVA-CSK from the Object Bar’s Devices category or from the Devices window into the worksheet (see also chapters: Devices and Configurations menu). The following dialog box appears: Bosch Security Systems B.V.
Page 983 Additional configuration windows can be navigated to by clicking on the icons at the top of the window. However, as a basic rule, IRIS-Net will remember which window was used last and reopen to this window next time you double click on the Call Station device icon.
Page 984 When pressing this button, the backlight of the call station's LCD screen blinks regularly in quick succession. The status indicator of the call station Device in IRIS-Net blinks at the same time. This function serves for checking communication and for identification or search of a call station in a larger system.
Page 985 Indicates the firmware version of the Call Station when on-line. UPDATE Press this button to update the firmware of the call station. NOTE: The default password for the firmware update is “0000”. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 986 Watchdog error in the Call Station. This error type is logged according standards, press the CLEAR button to reset the error. FIRMWARE The firmware version of the Call Station is too old. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 987: Pva-2P500
PVA-2P500 Device Start by creating a PVA-2P500 device in your IRIS-Net project. Drag a PVA-2P500 from the Object Bar’s Devices category or from the Devices window into the worksheet (see also chapters: Devices and Configurations menu). The following dialog box appears: Bosch Security Systems B.V.
Page 988 Additional configuration windows can be navigated to by clicking on the icons at the top of the window. However, as a basic rule, IRIS-Net will remember which window was used last and reopen to this window next time you double click on the device icon.
Page 989 Description MODEL Indicates PVA-2P500, so you know the model of the device. NAME IRIS-Net internal device name of the Amplifier. FIRMWARE Indicates the firmware version of the Amplifier when on-line. Opens the firmware update dialog. NOTE: The default password for the firmware update is “0000”.
Page 990 Element Description STATE The current condition of each type of error gets indicated. Green means no error, red indicates that an error has been detected. Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956...
Page 991 Watchdog error of the device. This error type is logged conforming to standards, press the CLEAR button to reset the error. FIRMWARE The firmware version is not compatible with the IRIS-Net version used. A firmware update is recommended. PROTECT Protect mode of amplifier activated.
Page 994 Bosch Sicherheitssysteme GmbH Robert-Bosch-Ring 5 85630 Grasbrunn Germany www.dynacord.com © Bosch Sicherheitssysteme GmbH, 2017...

Bosch IRIS-Net User Manual

Quick Links

Related Manuals for Bosch IRIS-Net

Summary of Contents for Bosch IRIS-Net

Table of Contents