Huawei Quidway S9300 Configuration Manual page 125

Quidway S9300 Terabit Routing Switch
Configuration Guide - Device Management
Configuration Roadmap
The configuration roadmap is as follows:
1.
2.
3.
Data Preparation
To complete the configuration, you need the following data:
l
l
Procedure
Step 1 Configure each interface to ensure that the routes between Layer 2 devices are reachable.
# Configure Switch A.
<Quidway> system-view [Quidway] sysname SwitchA [SwitchA] vlan batch 2 to 3
[SwitchA-vlan1] quit [SwitchA] interface GigabitEthernet 1/0/1 [SwitchA-
GigabitEthernet1/0/1] port link-type trunk [SwitchA-GigabitEthernet1/0/1] port
trunk pvid vlan 2 [SwitchA-GigabitEthernet1/0/1] port trunk allow-pass vlan 2
[SwitchA-GigabitEthernet1/0/1] quit [SwitchA] interface gigabitethernet 1/0/2
[SwitchA-GigabitEthernet1/0/2] port link-type trunk [SwitchA-GigabitEthernet1/0/2]
port trunk pvid vlan 3 [SwitchA-GigabitEthernet1/0/2] port trunk allow-pass vlan 3
[SwitchA-GigabitEthernet1/0/2] quit
# Configure Switch B.
<Quidway> system-view [Quidway] sysname SwitchB [SwitchB] vlan 2 [SwitchB-vlan2]
quit [SwitchB] interface gigabitethernet 1/0/1 [SwitchB-GigabitEthernet1/0/1] port
link-type trunk [SwitchB-GigabitEthernet1/0/1] port trunk pvid vlan 2 [SwitchB-
GigabitEthernet1/0/1] port trunk allow-pass vlan 2 [SwitchB-GigabitEthernet1/0/1]
quit [SwitchB] interface gigabitethernet 1/0/2 [SwitchB-GigabitEthernet1/0/2] port
link-type trunk [SwitchA-GigabitEthernet1/0/2] port trunk pvid vlan 2 [SwitchB-
GigabitEthernet1/0/2] port trunk allow-pass vlan 2 [SwitchB-GigabitEthernet1/0/2]
quit
# Configure Switch C.
<Quidway> system-view [Quidway] sysname SwitchC [SwitchC] vlan 2 [SwitchC-vlan2]
quit [SwitchC] interface gigabitethernet 1/0/1 [SwitchC-GigabitEthernet1/0/1] port
link-type trunk [SwitchC-GigabitEthernet1/0/1] port trunk pvid vlan 2 [SwitchC-
GigabitEthernet1/0/1] port trunk allow-pass vlan 2 [SwitchC-GigabitEthernet1/0/1]
quit [SwitchC] interface gigabitethernet 1/0/2 [SwitchC-GigabitEthernet1/0/2] port
link-type trunk [SwitchC-GigabitEthernet1/0/2] port trunk pvid vlan 2 [SwitchC-
GigabitEthernet1/0/2] port trunk allow-pass vlan 2 [SwitchC-GigabitEthernet1/0/2]
quit
Step 2 Configure the remote observing port.
# Configure GE 1/0/1 on Switch A as the remote observing port.
[SwitchA] observe-port 1 interface gigabitethernet 1/0/1 vlan 2
Step 3 Configure the remote mirrored port.
# Configure GigabitEthernet1/0/2 of SwitchA as the remote observing port to monitor packets
received by users.
Issue 03 (2011-12-29)
Configure each interface to ensure that the routes between Layer 2 devices are reachable.
Configure GE 1/0/1 on Switch A as the remote observing port.
Configure GE 1/0/2 on Switch A as a mirrored port.
ID of the VLAN to which packets are mirrored
Index of the observing port
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
6 Mirroring Configuration
113