Mitsubishi NZ2GFCF-D62PD2 User Manual page 246

Remote input
Signal name
(RX) No.
CH1 Update flag
(Latch count
value)
RX29
Update flag
(Sampling count
value)
RX41 CH2
Update flag
(Periodic pulse
count value)
244
• This signal turns on when CH Latch count value (RWr12 to RWr13, RWr2A to RWr2B) is
updated.
( Page 133, Section 8.8,
CH Latch count value (RWr12 to RWr13, RWr2A to RWr2B) is updated without resetting
this flag.
• This signal turns off when CH Update flag reset command (Latch count value) (RY28,
RY40) is turned on.
*1
• Up to ΔT
delay occurs until this signal turns on after CH Latch count value (RWr12 to
1
RWr13, RWr2A to RWr2B) is updated.
(For the overview of the operation, refer to the description of CH Update flag reset
completed (Latch count value) (RX28, RX40).)
*1 For ΔT , refer to Page 283, Appendix 4.
1
• This signal turns on when CH Sampling count value (RWr12 to RWr13, RWr2A to RWr2B)
is updated.
( Page 136, Section 8.9)
• CH Sampling count value (RWr12 to RWr13, RWr2A to RWr2B) is updated without
resetting this flag.
• This signal turns off when CH Update flag reset command (Sampling count value) (RY28,
RY40) is turned on.
*1
• Up to ΔT
delay occurs until this signal turns on after CH Sampling count value (RWr12
1
to RWr13, RWr2A to RWr2B) is updated.
(For the overview of the operation, refer to the description of CH Update flag reset
completed (Sampling count value) (RX28, RX40).)
For ΔT
*1 , refer to Page 283, Appendix 4.
1
• This signal turns on when CH Periodic pulse count, difference value (RWr12 to RWr13,
RWr2A to RWr2B), CH Periodic pulse count, present value (RWr14 to RWr15, RWr2C to
RWr2D), and CH Periodic pulse count value update check (RWr16 to RWr17, RWr2E to
RWr2F) are updated.
( Page 139, Section 8.10)
• CH Periodic pulse count, difference value (RWr12 to RWr13, RWr2A to RWr2B), CH
Periodic pulse count, present value (RWr14 to RWr15, RWr2C to RWr2D), and CH
Periodic pulse count value update check (RWr16 to RWr17, RWr2E to RWr2F) are updated
without resetting this flag.
• This signal turns off when CH Update flag reset command (Periodic pulse count value)
(RY28, RY40) is turned on.
*1
• Up to ΔT delay occurs until this signal turns on after CH Periodic pulse count, difference
1
value (RWr12 to RWr13, RWr2A to RWr2B), CH Periodic pulse count, present value
(RWr14 to RWr15, RWr2C to RWr2D), and CH Periodic pulse count value update check
(RWr16 to RWr17, RWr2E to RWr2F) are updated.
(For the overview of the operation, refer to the description of CH Update flag reset
completed (Periodic pulse count value) (RX28, RX40).)
For ΔT
*1 , refer to Page 283, Appendix 4.
1
Description
Page 145, Section 8.12)