Mitsubishi NZ2GFCF-D62PD2 User Manual page 106

(2) Comparison condition types and setting
Depending on the selected comparison condition, the range to be compared with the present value differs.
(a) Coincidence output
Coincidence output 1 to 4 turn on when CH Present value (RWr10 to RWr11, RWr28 to RWr29) matches with
a point set in Point setting (Coincidence output 1 to 4) (RWw0 to RWw1, RWw4 to RWw5, RWw8 to RWw9,
RWwC to RWwD).
Coincidence
output
(b) Within-range output
Coincidence output 1 to 4 turn on when both the following conditions are satisfied.
• When CH Present value (RWr10 to RWr11, RWr28 to RWr29) is Lower limit value setting (Coincidence
output 1 to 4) (RWw0 to RWw1, RWw4 to RWw5, RWw8 to RWw9, RWwC to RWwD) or more
• When CH Present value (RWr10 to RWr11, RWr28 to RWr29) is Upper limit value setting (Coincidence
output 1 to 4) (RWw2 to RWw3, RWw6 to RWw7, RWwA to RWwB, RWwE to RWwF) or less
(c) Out-of-range output
Coincidence output 1 to 4 turn on when either of the following conditions is satisfied.
• When CH Present value (RWr10 to RWr11, RWr28 to RWr29) is less than Lower limit value setting
(Coincidence output 1 to 4) (RWw0 to RWw1, RWw4 to RWw5, RWw8 to RWw9, RWwC to RWwD)
• When CH Present value (RWr10 to RWr11, RWr28 to RWr29) exceeds Upper limit value setting
(Coincidence output 1 to 4) (RWw2 to RWw3, RWw6 to RWw7, RWwA to RWwB, RWwE to RWwF)
Within-range
output
Out-of-range
output
104
Point setting (Coincidence output 1 to 4)
(RWw0 to RWw1, RWw4 to RWw5,
RWw8 to RWw9, RWwC to RWwD)
Coincidence output 1 to 4
(RX10 to RX13)
Coincidence output 1 to 4
terminals (EQU1 to EQU4)
Lower limit value setting
(Coincidence output 1 to 4)
(RWw0 to RWw1, RWw4 to RWw5,
RWw8 to RWw9, RWwC to RWwD)
Coincidence output 1 to 4
(RX10 to RX13)
Coincidence output 1 to 4 terminals
(EQU1 to EQU4)
Coincidence output 1 to 4
(RX10 to RX13)
Coincidence output 1 to 4 terminals
(EQU1 to EQU4)
ON
OFF
* To turn off Coincidence output 1 to 4 (RX10 to RX13),
use Reset command (Coincidence output 1 to 4) (RY10 to RY13).
(RWw2 to RWw3, RWw6 to RWw7,
RWwA to RWwB, RWwE to RWwF)
ON
OFF
ON
OFF
Present
value
Upper limit value setting
(Coincidence output 1 to 4)
Present value