Barco DP2K-12C Service Manual page 356

Index
engine fan - voltage low
engine fan - voltage too low
engine switch - not ok 37
fcb - force lps/lamp off (overtemperature, lamp house not
connected or engine not connected)
icp fan - speed low 72
icp fan - voltage high 73
icp fan - voltage low 73
imb - logical marriage tamper event
imb - no communication
imb - physical marriage tamper event
imb - service door tamper event
lamp - lamp is off due to an error
lamp - no communication
lamp - set lamp on failed
lamp - temperature high
lamp - temperature sensor open
lamp - temperature sensor short
lamp - temperature too high
lamp anode fan - speed low
lamp anode fan - speed too low
lamp anode fan - voltage high
lamp anode fan - voltage low
lamp anode fan - voltage too low
lamp cathode fan - speed low
lamp cathode fan - speed too low
lamp cathode fan - voltage high
lamp cathode fan - voltage low
lamp cathode fan - voltage too low
lamp house - not connected
lamp power supplies - at least one lamp power supply could not
be detected 59
lamp power supplies - communication failed
lamp power supplies - communication failed with at least one
lamp power supply 59
lamp power supplies - lamp is on, but smps is off
lamp power supplies - zero lamp power supplies detected
lamp rear fan - speed low
lamp rear fan - voltage high
lamp rear fan - voltage low
lamp rear fan - voltage too low
lamp run time - exceeds maximum
lamp run time - read failed
lamp run time - read limits failed
lamp run time - warning
lens - no lens parameter file has been activated
lens focus position - requested target not reached
lens horizontal shift position - requested target not reached
lens motors - voltage too low
lens vertical shift position - requested target not reached
lens zoom position - requested target not reached
light pipe - temperature high
light pipe - temperature sensor open
light pipe - temperature sensor short
light pipe - temperature too high
light sensor - no communication
maintenance - maintenance required
pfc heatsink - temperature high
prism switch - warning (lens probably touches prism)
smps fan - voltage high
smps fan - voltage low 55
smps fan - voltage too low
smps fan 1 (left side) - speed low
smps fan 2(right side) - speed low
smps primary heatsink - temperature high
smps secondary heatsink - temperature high
smps secondary heatsink - temperature sensor open
smps secondary heatsink - temperature sensor short
system - read projector identification failed
ti-boards - system status = fail
ti-icp - certificate error 65
ti-icp - icp board not detected
ti-icp - key error 66
ti-icp - read satellite info failed
ti-icp - read system status failed
ti-icp - satellite firmware mismatch
352
52
52
47
69
68
69
69
60
29
60
46
46
47
46
34
33
53
53
53
35
34
54
54
54
37
31
59
36
55
56
55
60
60
60
60
73
39
72
38
69
70
70
69
29
73
48
55
55
35
36
49
49
32
61
66
63
63
63
ti-icp - self test = fail
ti-link-decryptor - logical marriage tamper event
ti-link-decryptor - no communication
ti-link-decryptor - physical marriage tamper event
ti-link-decryptor - read system status failed
ti-link-decryptor - security log almost full
ti-link-decryptor - security log is full
ti-link-decryptor - security tamper event
ti-link-decryptor - service door tamper event
ti-link-decryptor - system error
Error code number
5003 29
5004 29
5005 31
5020 32
5042 32
5053 33
5072 33
5073 34
5082 34
5083 35
5103 35
5113 36
5123 36
5143 36
5160 37
5180 37
5191 38
5230 38
5231 39
5232 40
5233 41
5253 41
5263 42
5273 43
5280 43
58 5281 43
5283 43
5284 43
5285 43
5290 44
5291 44
5293 44
5294 44
5295 45
5300 45
5301 45
40 5303 45
5304 45
41 5305 46
5310 46
5311 46
5314 46
5315 47
5320 47
5331 48
5340 48
5341 48
38 5343 48
5344 48
5345 49
5351 49
5361 49
5364 49
5365 49
5371 49
49 5372 49
49 5373 50
5381 50
5382 50
5383 50
5391 50
5392 50
5393 51
5431 51
5432 51
65
66
68
68
68
67
62
66
29, 31–63, 65–73
R5905043 DP2K-12C/11CX 19/02/2018
68
68