CITROËN ID 19 Repair Manual page 35

ID 19 OPERATION No. ID
100-Z : Xnppmg and assemblzng an engzne-gearbox assembly
"P.
1lJ IUU-L 55
TOOLS
To Assemble.
To fit the distributor :
Put the distributor in position.
Move the distributor driving dog until it coincides with that of the oil pump.
Fit the metal fixing plate of the housing and tighten fixing screws (spring washer under head)
. . . . . . . . . . . . . . . . . .
Fit the dipstick support tube and the dipstick. Insert the earth lead terminal of contact breaker under the tube fixing
bracket. Tightenthe screw (plain and spring washer under head). Hook the distributor return spring to the
tubefixingbracket
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fit the crankcase breather, inserting a paper gasket.
Tighten the fixing screws (spring washer under head). . . . . .
Fit the petrol pump, inserting cork gasket.
Tighten the fixing nuts (spring washer) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
a>
Fit the inlet manifold, inserting a gasket. Tighten fixing screws (plain washer under head) . . . . . . . . . . . . . . . .
b) Fit carburettor, inserting a fibre gasket. Tighten nuts (spanner 1645-T, see Pl.
16,
fig. 3) . . . . . . . . . . . . . . . .
cl
Connect the flexible petrol feed pipe to the carburettor.
d)
Connect the vacuum pipe to the distributor and the carburettor.
12 mm box spanner
12 mm box spanner
12 mm box spanner
14 mm box spanner
12 mm box spanner
Spanner 1645-T
Fit and adjust the position of high pressure pump (see Op. ID 111-O).
4
Fit the pressure regulator and its intermediate support.
Fit the fixing screws without tightening them (spring
washers under heads).
b)
Fit the pipe connecting the pump and the control valve. Tighten unions (spanner 2220-T, see ~1.61, fig. 3). . .
c>
Tighten intermediate support fixing Bcrews. Fit only the 2nd type support,
reinforced with 2 welded plates.
Fit the steel water outlet pipe on the cylinder head.
Insert the gasket sealed with "hermetic". Tighten the fixing
screws (plain washers under heads) and insert the screen locking plate
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fit the exhaust pipe, inserting gaskets.
Fit the bracket for fixing the screen (longest at the front). Tighten all the
nuts progressively(springwashers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fit the starter. Tightenthe fixing screw and locknut
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Spanner 2220-T
12 mm box spanner
12 mm box spanner
12 mm box spanner
14-17 mm box
spanners
6
7
8
9
10
11
12
13
14
15