CITROËN ID 19 Repair Manual page 19

No. OF
ILLUSTRATION
GEARBOX
42 Stand for supporting engine on the car and removing gearbox
42 Support fixture
54 Spanner for clutch housing screws (two flats) . . . . . . . . . . . . .
61 Spanner for clutch housing screws (hexagon)
55 Spanner for nut of water pump driving pulley shaft . . . . . . . . .
101 Lever for disengagement of front brake shoes . . . . . . . . . . . . .
101 Fork for disengagement of brake catch
101 Spanner for adjustment of front brakes
53 Stand for gearbox for use on a bench . . . . . . . . . . . . . . . . . . . .
54 Spanner for bevel pinion nut . . . . . . . . . . . . . . . . . . . . . . . . . . .
57 Extractor body . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
52 Collet ring and thrust block for differential bearing extractor
52 Pad for differential shaft bearing extractor . . . . . . . . . . . . . . . .
57 Split collar and pressure pad for bevel pinion front bearing extractor
55 Spanner for nut of differential bearing (on shaft) . . . . . . . . . . .
55 Spanner for nut of differential bearing (in housing) . . . . . . . . .
57 Spring compressor for locking lever spring . . . . . . . . . . . . . . .
57 Spanner for spindle caps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
-58 Fixture for alignment of pulleys . . . . . . . . . . . . . . . . . . . . . . . .
56 Mandrel for positioning fork control balls . . . . . . . . . . . . . . . .
6 Fixture for calibrating springs
52 Mandrel for fitting differential bearings . . . . . . . . . . . . . . . . . .
55 Mandrel for fitting the oil seal on the differential shaft . . . . . .
55 Mandrel and bush for fitting the seal in the outside of the
differential bearing housing
13 Straight edge for dial gauge
54 Mandrel for mainshaft hearing . . . . . . . . . . . . . . . . . . . . . . . . .
54 Mandrel for assembly of bevel pinion
50 Fixture for adjusting crown wheel and bevel pinion . . . . . . . . .
51 Fixture for adjustment of differential bearings . . . . . . . . . . . . .
51 Dial gauge extension (differential bearing adjustment) . . . . . .
50 Support for dial gauge (adjustment of tooth clearance) . . . . . .
50 Dial gauge extension (adjustment of tooth clearance) . . . . . . .
61 Spanner for ball joint cups . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
61 Press for fitting selector ball joints . . . . . . . . . . . . . . . . . . . . . .
125 Hydraulic test bench
61 Spanner for hydraulic pipe union (9 mm opening) . . . . . . . . . .
61 Spanner for hydraulic pipe union (10 mm opening) . . . . . . . . .
INDEX OF SPECIAL TOOLS SHOWN IN THE MANUAL
DESCRIPTION
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
PRESSURE RESERVE UNITS
SERVICE
METHODS No. TOOL ON SALE REMARKS
. . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . .
MR-3053-130
MR-3691-80
. . . . . . . . . . . . . . . . . . . MR-3676-30
MR-3691-60
REFERENCE OF
1797-T
1799-T
1677-T
2431-T
1640-T
2127-T
2128-T
2129-T
1734-T
1750-T
1753-T
1742-T
1738-T
1770-T
1771-T
1792-T
1683-T
1793-T
2420-T see engine
1768-T
1767-T
1772-T
MR-3377
MR-3045
2044-T
1766-T
2438-T
2039-T
2439-T
2427-T
2290-T
2219-T
2221-T
17
IMPORTANCE
2
2
1
I
2
1
1
1
2
2
1
1
1
2
1
1
2
3
1
2
3
1
3
1
3
3
1
1
1
1
1
2
1
1
1
1