CITROËN DS5 Owner's Handbook Manual
  1. Manuals
  2. Brands
  3. CITROËN Manuals
  4. Automobile
  5. DS5 DSign
  6. Owner's handbook manual

CITROËN DS5 Owner's Handbook Manual

Hide thumbs Also See for DS5:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Handbook, Owner's Handbook Manual
OWNER'S HANDBOOK

Advertisement

Table of Contents
loading

Related Manuals for CITROËN DS5

Summary of Contents for CITROËN DS5

  • Page 1 OWNER'S HANDBOOK...
  • Page 2 On-line owner's handbook You can fi nd your handbook on the CITROËN website, under Referring to the owner's handbook on-line also gives you "MyCitroën". access to the latest information available, easily identifi ed by the bookmark, associated with this symbol: This personal and customisable space allows you to establish direct and special contact with CITROËN.
  • Page 3 We draw your attention to the following... The "Familiarisation" section at the start of this document is intended as a quick way of getting CITROËN has a presence on every continent, to know your vehicle. Reading the detailed sections is essential to make the most of your a complete product range, vehicle, in complete safety.
  • Page 4 Familiarisation Familiarisation...

  • Page 5: Daytime Running Lamps

    Exterior Stop & Start This system puts the engine temporarily into standby during stops in the traffic (red lights, traffic jams, etc...). The engine restarts automatically as soon as you want to move off. The Stop & Start system reduces fuel consumption and exhaust emissions, and offers the comfort of complete silence when stationary.

  • Page 6: Automatic Headlamp Dipping

    Familiarisation Exterior Reversing camera This system, available only with satellite navigation, is activated automatically on Automatic headlamp dipping engaging reverse gear and provides an image This system automatically changes between in the colour screen. dipped and main beam, depending on the lighting and traffic conditions, using a camera located in the interior rear view mirror.

  • Page 7: Keyless Entry And Starting

    Access Keyless Entry and Starting Fuel tank Electronic key Unlocking Opening the fuel filler flap. Tank capacity: approximately 60 litres. With the electronic key on your person and in the recognition zone A around the vehicle, pass your hand behind the door handle to unlock the vehicle, then pull on the handle to open the door.
  • Page 8 Familiarisation Interior Audio and communication systems These systems benefit from the latest Head-up display technology: MP3 compatible audio systems, This system projects speed and cruise control/ USB player, Bluetooth hands-free system, speed limiter information onto a smoked strip satellite navigation system with colour screen, in the driver's field of vision, so that they do not auxiliary inputs, Hi-Fi audio system, ...

  • Page 9: Switch Panels

    Switch panels Illumination of the warning lamp indicates the state of the corresponding function. Deactivation of parking sensors. Activation of lane departure warning. Push button starting/stopping. Deactivation of the DSC/ASR Deactivation of the alarm. Locking/unlocking the passenger systems. compartment. Deactivation of Stop & Start. Opening the fuel filler flap.

  • Page 10: Sitting Comfortably

    Familiarisation Sitting comfortably Front seats Manual Head restraint height and angle adjustment. 2. Backrest angle adjustment. 3. Seat cushion height adjustment. 4. Seat forwards-backwards adjustment. 5. Driver's lumbar support adjustment. Electrical Angle, seat height and seat forwards- backwards adjustment. 2. Backrest angle adjustment. 3.
  • Page 11 Instruments and controls Bonnet release lever. 14. Controls for electric windows / electric child 27. Driver's airbag. 2. Headlamp height adjustment. lock / central locking. Horn. 3. Side adjustable air vents. 15. eMyWay controls. 28. Cruise control / speed limiter controls. 4.
  • Page 12 Familiarisation...

  • Page 13: Head Restraint Adjustment

    Sitting comfortably Head restraint adjustment Steering wheel adjustment Heated seats control To lower it, simultaneously press button A and Release the adjustment mechanism. 0 : off. push down on the head restraint. 2. Adjust for height and reach. 1 : low. To raise it, guide the head restraint upwards to 3.
  • Page 14 Familiarisation Sitting comfortably Door mirrors Rear view mirror Front seat belts Adjustment Automatic detection of day/night mode. Selection of the left or right mirror. 2. Rear view mirror adjustment. 2. Adjusting the position of the mirror glass. 3. De-selection of the mirror. 4.
  • Page 15 Seeing clearly Lighting Wipers Switching on "AUTO" mode Ring A Control stalk A: windscreen wipers  Briefly push the stalk downwards. Fast wipe. Lighting off. Normal wipe. Switching off "AUTO" mode Automatic illumination of headlamps. Int. Intermittent wipe. Park.  Briefly push the stalk downwards or place Sidelamps.

  • Page 16: Instrument Panel

    Familiarisation Monitoring Instrument panel Warning lamps On switching on, the dial needles go to the C. With the ignition on, the instrument panel With the ignition on, the orange and red extent of their travel then return to 0. screen should indicate the oil level * . warning lamps come on.

  • Page 17: Passenger Safety

    Passenger safety Front passenger's airbag Front seat belts and passenger's front airbag A. Left hand front seat belt not fastened or E. Left hand rear seat belt not fastened or unfastened warning lamp. unfastened warning lamp. B. Right hand front seat belt not fastened or Front passenger's airbag deactivated unfastened warning lamp.

  • Page 18: Driving Safely

    Familiarisation Driving safely Electric parking brake Before leaving the vehicle, check that the the brake warning lamp and the P warning lamp in the control lever A are on fixed (not flashing) . If towing a trailer or caravan or if the slope might vary (transport by boat or lorry, recovery of the vehicle...) make a maximum application of the parking...

  • Page 19: Starting / Stopping The Engine

    Driving safely Starting - stopping the engine Before starting Starting at temperatures Starting at temperatures above zero below zero Place the gear lever in neutral or in position N for an electronic or automatic Press the brake pedal. You must initiate preheating of the Diesel gearbox.

  • Page 20: Display In The Instrument Panel

    Familiarisation Driving safely Speed limiter "LIMIT" Cruise control "CRUISE" Display in the instrument panel The cruise control or speed limiter mode appears in the instrument panel when it is selected. Gear shift indicator Selecting speed limiter mode. Selecting cruise control mode. 2.
  • Page 21 Driving safely Stop & Start Going into engine STOP mode Going into engine START mode Deactivation / Reactivation The "ECO" warning lamp comes on The "ECO" warning lamp goes off in the instrument panel and the engine and the engine restarts automatically: goes into standby automatically: with a manual gearbox , when you fully depress the clutch pedal,...

  • Page 22: Eco-Driving

    Familiarisation Eco-driving Eco-driving is a range of everyday practices that allow the motorist to optimise their fuel consumption and CO emissions. Optimise the use of your gearbox Control the use of your electrical equipment With a manual gearbox, move off gently and change up without waiting. Before moving off, if the passenger compartment is too warm, ventilate it During acceleration change up early.
  • Page 23 Limit the causes of excess consumption Observe the recommendations on maintenance Spread loads throughout the vehicle; place the heaviest items in the Check the tyre pressures regularly, when cold, referring to the label in bottom of the boot, as close as possible to the rear seats. the door aperture, driver's side.

  • Page 24: Instruments And Controls

    Instruments and controls...

  • Page 25: Control Buttons

    Petrol-Diesel instrument panel Dials and screens Control buttons Rev counter (x 1 000 rpm or tr/min), 6. Gear shift indicator or gear lever position A. Main lighting and controls dimmer. graduation according to engine (petrol or and gear for an electronic or automatic B.

  • Page 26: Indicator And Warning Lamps

    Monitoring Indicator and warning lamps Visual indicators informing the driver that a When the engine is started, these same Certain warning lamps may come on in system is in operation, switched off or has a warning lamps should go off. one of two modes: fixed (continuous) or fault.

  • Page 27: Operation Indicator Lamps

    Operation indicator lamps If one of the following indicator lamps comes on in the instrument panel and/or instrument panel screen, this confirms that the corresponding system has come into operation. Warning / indicator lamp State Cause Action / Observations Left-hand flashing with buzzer.
  • Page 28 Monitoring Warning / indicator lamp State Cause Action / Observations Rear foglamps fixed. The rear foglamps are switched on. Turn the ring on the stalk rearwards to switch off the rear foglamps. Diesel engine fixed. The START/STOP switch has been Wait until the warning lamp goes off before starting.
  • Page 29 Warning / indicator lamp State Cause Action / Observations Automatic fixed. The wiper control is pushed Automatic front wiping is activated. wiping downwards. To deactivate automatic wiping, operate the control stalk downwards or put the stalk into another position. Passenger's fixed in the seat belt The control switch, located in the glove Move the control switch to the "OFF"...
  • Page 30 Monitoring Deactivation indicator lamps If one of the following indicator lamps comes on, this confirms that the corresponding system has been switched off intentionally. This is may be accompanied by an audible signal and a message in the instrument panel screen. Warning / indicator lamp State Cause...

  • Page 31: Warning Lamps

    Warning lamps When the engine is running or the vehicle is being driven, illumination of one of the following warning lamps indicates a fault which requires action on the part of the driver. Any fault resulting in the illumination of a warning lamp must be investigated further by reading the associated message in the instrument panel screen. If you encounter any problems, contact a CITROËN dealer or a qualified workshop.
  • Page 32 Monitoring Warning / indicator lamp State Cause Action / Observations Service on temporarily. A minor fault has occurred for which Identify the fault by reading the message shown in the there is no specific warning lamp. screen, such as, for example: opening of the doors, boot or bonnet, engine oil low level, screenwash low level,...
  • Page 33 Warning / indicator lamp State Cause Action / Observations Electric parking flashing. The electric parking brake is not You must stop as soon as it is safe to do so. brake applied automatically. Park on flat level ground, engage a gear (or place the The application/release is faulty.
  • Page 34 Monitoring Warning / indicator lamp State Cause Action / Observations Braking fixed. The braking system fluid level has You must stop as soon as it is safe to do so. dropped significantly. Top up with brake fluid listed by CITROËN. If the problem persists, have the system checked by a CITROËN dealer or a qualified workshop.
  • Page 35 Warning / indicator lamp State Cause Action / Observations Engine flashing. The engine management system has Risk of destruction of the catalytic converter. autodiagnosis a fault. Have it checked by a CITROËN dealer or a qualified system workshop. fixed. The emission control system has The warning lamp should go off when the engine is started.
  • Page 36 Monitoring Warning / indicator lamp State Cause Action / Observations Seat belt(s) fixed A seat belt has not been fastened or Pull the strap then insert the tongue in the buckle. not fastened / or flashing has been unfastened. unfastened accompanied by an audible signal.

  • Page 37: Coolant Temperature Gauge

    Coolant temperature gauge After driving for a few minutes, the temperature and pressure in the cooling system increase. To top up the level:  wait for the engine to cool,  unscrew the cap by two turns to allow the pressure to drop, ...

  • Page 38: Service Indicator

    Monitoring Service indicator More than 1 800 miles (3 000 km) Less than 600 miles (1 000 km) System which informs the driver when the remain before the next service is due remain before the next service is due next service is due, in accordance with the manufacturer's servicing schedule.
  • Page 39 Service overdue Service indicator zero reset Retrieving the service information For 5 seconds after the ignition is switched on, the spanner flashes to indicate that the service You can access the service information at any must be carried out as soon as possible. time.

  • Page 40: Engine Oil Level Indicator

    Monitoring Engine oil level indicator * On versions fitted with an electric oil level indicator, the state of the engine oil level is displayed in the instrument panel for a few seconds, after the servicing information. Oil level correct Oil level indicator fault The level read will only be correct if This is signalled by the display of the message "Oil the vehicle is on level ground and the...

  • Page 41: Distance Recorders

    Distance recorders Lighting dimmer The total and trip distances are displayed for thirty seconds when the ignition is switched off, when the driver's door is opened and when the vehicle is locked or unlocked. System for manual adjustment of the brightness of the instruments and controls in relation to the exterior brightness.
  • Page 42 Monitoring Black panel (black screen) with eMyWay System allowing certain screens to be switched off for night driving (available only with For more information, refer to the eMyWay). eMyWay part of the "Audio and The instrument panel remains on with the telematics"...

  • Page 43: Setting The Date And Time

    Setting the date and time Clock Audio system / Bluetooth Using the arrows, select " Display configuration " and confirm. Using the arrows, select " Date and time adjustment " and confirm. The analogue clock does not have an Press MENU . adjustment button.
  • Page 44 Monitoring eMyWay The clock, located in the dashboard, is synchronised with the time in the screen. It is set once the time is adjusted using the " SETUP " menu and every time the ignition is switched on. Select " Display configuration " and confirm. Select "...

  • Page 45: Trip Computer

    Trip computer System that gives you information on the journey in progress (range, fuel consumption…). Instrument panel screen Trip reset The current information tab with: ● the range, ● the current fuel consumption, ● the Stop & Start time counter. Information display Trip "1"...
  • Page 46 Monitoring Trip computer, a few definitions… Range Current fuel consumption Average speed (miles or km) (mpg or l/100 km or km/l) (mph or km/h) This indicates the distance This is the average fuel consumption This is the average speed calculated during the last few seconds.
  • Page 47 Access...

  • Page 48: Electronic Key Remote Control

    Electronic key remote control Unlocking the vehicle Complete unlocking Selective unlocking This setting is done in the  Press the open padlock to unlock configuration menu. the vehicle. Complete unlocking is activated by default.  To unlock only the driver's door, press the open padlock once.

  • Page 49: Unlocking The Boot

    Access Unlocking the boot Locking the vehicle  Press this button until you hear  Press the closed padlock to lock If one of the doors or the boot is not fully the boot unlock. The vehicle is the vehicle completely. closed, locking does not take place.

  • Page 50: "Keyless Entry And Starting" System

    "Keyless Entry and Starting" system Unlocking the vehicle Selective unlocking Complete unlocking This setting is done via the configuration menu. By default, complete unlocking is activated.  To unlock only the drivers door, with the electronic key on your person, pass your hand behind the driver's door handle then pull the door handle to open.

  • Page 51: Locating Your Vehicle

    Access Locking the vehicle Locating your vehicle This function allows you to identify Ensure that no one prevents the correct your vehicle from a distance, operation of the windows. particularly in poor light. Your vehicle Be aware of children when operating must be locked.

  • Page 52: Using The Remote Control

    Deadlocking Using the remote control With the Keyless Entry and Deadlocking renders the exterior and Starting system interior door controls inoperative.  Press the closed padlock to lock It also deactivates the manual central the vehicle completely. control button. Maintain pressure with your Therefore, never leave anyone inside finger for more than two seconds the vehicle when it is deadlocked.
  • Page 53 Access Back-up mechanical key Unlocking/locking using the integral key Complete unlocking Normal locking The integral key is used to lock and unlock the vehicle when the electronic key cannot operate:  Turn the key towards the front of the  Turn the key towards the rear of the vehicle cell battery flat, vehicle battery discharged vehicle to unlock the vehicle.
  • Page 54 Remote control problem - Changing the battery of reinitialisation the electronic key Following disconnection of the vehicle battery, replacement of the remote control battery or in the event of a remote control malfunction, you can no longer unlock, lock or locate your vehicle.

  • Page 55: Electrical Interference

    Access Lost electronic key Visit a CITROËN dealer with the vehicle's registration document and your personal identification documents and if possible the key code label. The CITROËN dealer will be able to retrieve the key code and the transponder code required to order a new key. Electronic key The electronic key is a sensitive system;...

  • Page 56: Central Locking Control

    Central locking control Automatic central locking of the Emergency control doors System allowing the doors to be locked and (anti-intrusion security) unlocked manually in the event of a malfunction of the central locking system or battery failure. The doors and boot can lock automatically while driving (speed above 6 mph (10 km/h)).
  • Page 57 Access Locking the front and rear Unlocking the front and rear passenger doors passenger doors  Open the doors.  Pull the interior door opening control.  On the rear doors, check that the child lock is not on (see the corresponding section). ...
  • Page 58 Boot Opening from outside Opening from inside Tailgate release System allowing the mechanical unlocking of the boot in the event of a battery or central locking system malfunction.  After unlocking the boot or the vehicle  Press this button until the boot is heard to using the electronic key - remote control, unlock.
  • Page 59 Access Alarm - Tilt The monitoring system is active: the indicator lamp in the button flashes once per second. The system checks for any change in the After the locking button on the remote control attitude of the vehicle. is pressed or the vehicle locked using the The alarm is triggered if the vehicle is lifted, Keyless Entry and Starting system, the exterior moved or knocked.
  • Page 60 Locking the vehicle with exterior perimeter monitoring only Deactivate the interior volumetric and anti-lift Deactivation of the interior Where the vehicle locks itself again monitoring to avoid unwanted triggering of the volumetric and anti-tilt monitoring automatically (occurs 30 seconds after alarm in certain cases such as: unlocking, if a door or the boot is not ...

  • Page 61: Triggering Of The Alarm

    Access Triggering of the alarm Locking the vehicle without activating the alarm This is indicated by sounding of the siren and flashing of the direction indicators for  Lock or deadlock the vehicle using the key thirty seconds. (integral with the remote control) in the Reactivation of the interior The monitoring functions remain active until driver's door lock.

  • Page 62: Electric Windows

    Electric windows Manual operation To open or close the window, press or pull the switch gently. The window stops as soon as the switch is released. Automatic operation To open or close the window, press or pull switch fully: the window opens or closes completely when the switch is released.
  • Page 63 Access Safety anti-pinch When the window rises and meets an obstacle, Reinitialisation of the it stops and immediately partially lowers again. electric windows In the event of unwanted opening of the window on closing, press the switch until the Following reconnection of the battery, the window opens completely, then pull the switch In the event of contact during operation safety anti-pinch function must be reinitialised.

  • Page 64: Cockpit Glass Roof

    Cockpit glass roof Electric blinds A tinted glass panoramic surface to increase There are two options for opening and closing: the light and visibility in the passenger compartment. Fitted with three electric blinds to improve  Pull or press the control without going ...
  • Page 65 Access Safety anti-pinch In automatic mode and at the end of its travel, If the blind stops and immediately opens again If the blind meets an obstacle during if the blind meets an obstacle while closing it during a closing manoeuvre: operation, you must reverse the stops and moves back slightly.
  • Page 66 Fuel tank Capacity of the tank: approximately 60 litres . Opening Refuelling  Introduce the nozzle and push it in fully (pushing open the non-return valve A on petrol vehicles).  Fill the tank (don't continue past the third cut-off of the nozzle, as this may cause malfunctions).

  • Page 67: Misfuel Prevention (Diesel)

    Access Misfuel prevention (Diesel) * Mechanical device which prevents filling the tank of a Diesel vehicle with petrol. It avoids the risk of engine damage that can result from filling with the wrong fuel. Low fuel level Located in the filler neck, the misfuel prevention device appears when the filler cap is removed. When the low fuel level in the Operation tank is reached, this warning lamp...
  • Page 68 Quality of the fuel used for Quality of the fuel used for petrol engines Diesel engines The petrol engines are perfectly compatible The Diesel engines are perfectly compatible with E10 or E24 type petrol biofuels (containing with biofuels which conform to current and 10 % or 24 % ethanol), conforming to European future European standards (Diesel fuel standards EN 228 and EN 15376.
  • Page 69 Comfort...

  • Page 70: Front Seats

    Front seats Manual Adjustments to the height and angle of the head restraint To raise it, pull upwards. To lower it, press on the lug and the head restraint at the same time. 2. Adjustment of the backrest angle Turn the wheel to adjust the angle of the backrest.
  • Page 71 Comfort Electric Adjustment of the seat cushion angle and height, and forwards-backwards adjustment  Raise or lower the front of the control to adjust the seat cushion angle.  Raise or lower the rear of the control to raise or lower the seat. ...

  • Page 72: Storing Driving Positions

    Storing driving positions Storing a position using Recalling a stored position buttons M / 1 / 2  Briefly press button 1 or 2 to recall the  Switch on the ignition. corresponding position.  Adjust your seat and the head-up display. An audible signal indicates the end of the ...
  • Page 73 Comfort Head restraint height and angle adjustment  To raise a head restraint, pull it upwards. The head restraint is fitted with a frame with notches which prevents it from  To remove the head restraint, press the lug A and pull the head restraint upwards. lowering;...

  • Page 74: Massage Function

    Heated seats control Massage function Activation  Press this switch. Its indicator lamp comes on and the massage function is activated for a period of 1 hour. During this time, massage is performed in 6 cycles of 10 minutes (6 minutes of massage followed by 4 minutes break).

  • Page 75: Rear Seats

    Comfort Rear seats Bench seat with split cushion and backrest (left hand 2/3, right hand 1/3) which can be folded individually to adapt the load space in the boot. Folding the cushion and backrest  Lift the cushion 1 by hand, lifting from the rear.
  • Page 76 Repositioning the seat backrest and cushion  Keep the seat belt guide 2 held against the  Reposition the cushion 1 . When repositioning the seat backrest, vehicle to avoid trapping the seat belt when  Release the seat belt guide 2 . take care not to trap the seat belts.

  • Page 77: Removing The Seat Cushion

    Comfort Removing the seat cushion Rear head restraints These have one position for use (up) and a  Remove the seat cushion 1 from its fixings Never drive with the head restraints by pulling upwards. stowed position (down). removed; they must be in place and They can also be removed.

  • Page 78: Door Mirrors

    Mirrors Door mirrors Folding Automatic: lock the vehicle using the electronic key. Manual: with the ignition on, move control A downwards. If the mirrors are folded using control A , they will not unfold when the vehicle is unlocked. Adjustment Each fitted with an adjustable mirror glass providing the lateral rearward vision necessary Unfolding...

  • Page 79: Rear View Mirror

    Comfort Steering wheel adjustment Rear view mirror Seeing clearly Adjustable mirror providing a central rearward view. Equipped with an anti-dazzle system, which darkens the mirror glass and reduces the nuisance to the driver caused by the sun, headlamps from other vehicles... Automatic day/night model ...

  • Page 80: Interior Fittings

    Interior fi ttings Glove box 2. Storage 3. Storage (according to version) 4. Ticket holder (according to version) 5. Removable ashtray / 12 V accessory socket (120 W) Press the lid to open the ashtray. To empty the ashtray, remove it by pulling it upwards.
  • Page 81 Comfort Cigarette lighter / Mats 12 V accessory Removable carpet protection. socket Fitting Refitting To refit the mat on the driver's side:  position the mat correctly,  refit the fixings by pressing,  check that the mat is secured correctly. To avoid any risk of jamming of the pedals: only use mats which are suited to...

  • Page 82: Centre Armrest

    Centre armrest USB Player Comfort and storage system for the driver and This connection box, consisting of a JACK When the USB port is used, the portable device front passenger. auxiliary socket and a USB port, is located in charges automatically. the front armrest (under the cover).

  • Page 83: Rear Armrest

    Comfort Rear armrest Ski fl ap  Lower the rear armrest for a more Facility for storing and transporting long objects. comfortable position. It may be fitted with cup holders and also gives access to the ski flap. Opening  Lower the armrest. ...

  • Page 84: Boot Fi Ttings

    Boot fi ttings Rear shelf It can be removed when carrying large objects. 2. Bag hooks 3. Stowing rings 4. Warning triangle retaining straps...

  • Page 85: Warning Triangle (Stowing)

    Comfort Warning triangle (stowing) Placing the triangle on the road Use the straps on the interior boot trim to stow the folded triangle or its storage box. Place the triangle behind the vehicle, as required by the legislation in force in your country.

  • Page 86: Heating And Ventilation

    Heating and Ventilation System which creates and maintains good conditions of comfort and visibility in the vehicle's passenger compartment. Controls The incoming air follows various routes depending on the controls selected by the driver, the front passenger and rear passengers. The temperature control enables you to obtain the level of comfort required by mixing the air of the various circuits.

  • Page 87: Recommendations For Ventilation And Air Conditioning

    Comfort Recommendations for ventilation and air conditioning In order for these systems to be fully effective, follow the operation and maintenance If after an extended stop in sunshine, guidelines below: the interior temperature is very high, first  To obtain an even air distribution, take care not to obstruct the exterior air intake grilles ventilate the passenger compartment for located at the base of the windscreen, the nozzles, the vents and the air outlets, as well a few moments.

  • Page 88: Dual-Zone Digital Air Conditioning

    Dual-zone digital air conditioning Automatic operation When the engine is cold, the air flow will reach its optimum level progressively, taking account of the weather and the desired comfort level so as to avoid too great a distribution of cold air. On entering the vehicle, if the interior temperature is much colder or warmer than the comfort value, there is no...
  • Page 89 Comfort Manual operation 4. Automatic visibility 2-3. Driver's-passenger's side If you wish, you can make a different choice programme from that offered by the system by changing a settings setting. The "AUTO" indicator lamps go off; the The driver and front passenger can See "Front demisting - defrosting".

  • Page 90: Air Fl Ow Adjustment

    5. Air conditioning On / Off 6. Air distribution adjustment 8. Air intake / Air recirculation Air recirculation enables the passenger  Press this button to switch off  Press one or more buttons to compartment to be isolated from exterior odours the air conditioning.

  • Page 91: Maximum Air Conditioning

    Comfort 9. Maximum air conditioning Switching the system off  If you want to quickly cool  Turn the air flow control to the the air in the passenger left until all of the indicator compartment, press this lamps go off. button;...

  • Page 92: Front Demist - Defrost

    Front Demist - Rear screen and door mirrors demist - Defrost defrost Switching on Automatic visibility programme  Press this button (located on  Switch off the demisting/defrosting the air conditioning system of the rear screen and door mirrors  Select this programme control panel) to demist/defrost as soon as appropriate, as lower to demist or defrost the...
  • Page 93 Driving...

  • Page 94: Starting-Switching Off The Engine

    Starting-switching off the engine With a manual gearbox , put the gear lever in neutral. With an electronic gearbox , put the gear lever in N . If one of the starting conditions is not With an automatic gearbox , put the gear lever in P or N . met, a reminder message appears in Starting using Starting with the "Keyless...

  • Page 95: Anti-Theft Protection

    Driving Ignition on without Anti-theft protection starting Switching off using the Electronic engine immobiliser electronic key The keys contain an electronic chip which has With the electronic key in the reader or the  Immobilise the vehicle. a secret code. When the ignition is switched Keyless Entry and Starting key inside the on, this code must be recognised in order for vehicle, pressing the "START/STOP"...

  • Page 96: Emergency Switch-Off

    Emergency starting with the Emergency switch-off Electronic key not recognised by Keyless Entry and Starting the "Keyless Entry and Starting" system system In the event of an emergency only, the engine can be switched of without conditions. To do this, press and hold the "START/STOP" button for about 3 seconds.

  • Page 97: Electric Parking Brake

    Driving Electric parking brake Programming the automatic mode It is recommended that you do not apply the parking brake in very cold Depending on the country of sale of the vehicle, the automatic application when the engine is conditions (ice) and during towing switched off and the automatic release when (breakdown, caravan...).

  • Page 98: Manual Application

    Manual application Manual release With the vehicle stationary, to apply the parking brake whether the engine is running or off, pull Maximum application control lever A . If necessary, you can make a maximum The application of the parking brake is application of the parking brake.

  • Page 99: Automatic Release

    Driving Automatic application, Automatic release engine off The electric parking brake releases automatically and progressively when you Immobilising the vehicle, With the vehicle stationary, the parking brake press the accelerator: engine running is automatically applied when the engine is  Manual gearbox : fully depress the clutch switched off.

  • Page 100: Emergency Braking

    Emergency braking In the event of a failure of the main service The emergency braking must only be brake or in an exceptional situation (e.g. driver used in exceptional circumstances. taken ill, under instruction, etc) a continuous pull on the control lever A will stop the vehicle. The Dynamic Stability Control system provides stability during emergency braking.

  • Page 101: Operating Faults

    Driving Operating faults If the electric parking brake fault warning lamp comes on together with one or more of the warning lamps presented in these tables, place the vehicle in a safe condition (on level ground, gear engaged) and contact a CITROËN dealer or a qualified workshop without delay. Situations Consequences Display of the message "...
  • Page 102 Situations Consequences To apply the electric parking brake:  immobilise the vehicle and switch off the ignition.  pull the control for at least 5 seconds or until application is complete.  switch on the ignition and check that the electric parking brake and possibly warning lamps come on.

  • Page 103: Special Situations

    Driving Special situations In some circumstances (engine start...), In the event of a malfunction of the parking the parking brake may adjust the level of brake in the on position or a battery failure, application itself. This is normal operation. manual release remains possible.

  • Page 104: Hill Start Assist

    Hill start assist Operation System which keeps your vehicle immobilised temporarily (approximately 2 seconds) when starting on a gradient, the time it takes to move your foot from the brake pedal to the accelerator pedal. This system only operates when: the vehicle is completely stationary, with your foot on the brake pedal, in particular conditions on a slope,...

  • Page 105: Engaging Reverse Gear

    Driving 6-speed manual gearbox Engaging 5th or 6th gear  Move the lever fully to the right to engage 5th or 6th gear. Engaging reverse gear  Raise the trigger under the knob and move the gear lever to the left then forwards. Only engage reverse gear when the vehicle is stationary with the engine at idle.

  • Page 106: Automatic Gearbox

    Automatic gearbox Gear selection gate Displays in the instrument panel Six speed automatic gearbox which offers a choice between the comfort of fully automatic operation, enhanced by sport and snow programmes, or manual gear changing. Four driving modes are offered: automatic operation for electronic management of the gears by the gearbox, sport programme for a more dynamic style...

  • Page 107: Moving Off

    Driving Moving off Automatic operation  With your foot on the brake, select  Select position D for automatic changing If you do not press the brake pedal position P or N . of the six gears. when trying to move the gear lever ...

  • Page 108: Manual Operation

    Sport and snow programmes Return to automatic Manual operation operation  Select position M for sequential changing These two special programmes supplement the  At any time, press the button selected of the six gears. automatic operation in very specific conditions again to quit the programme engaged and ...

  • Page 109: Stopping The Vehicle

    Driving Operating fault Invalid value during manual When the ignition is on, a message appears operation in the instrument panel screen to indicate a gearbox fault. This symbol is displayed if a gear In this case, the gearbox switches to back-up is not engaged correctly (selector mode and is locked in 3rd gear.

  • Page 110: Electronic Gearbox

    Electronic gearbox Gear lever Steering mounted control paddles Six-speed electronic gearbox system which offers a choice between the comfort of fully automatic operation or the pleasure of manual gear changing. There are two driving modes: automatic mode for automatic control of the gears by the gearbox, manual mode for sequential gear changing by the driver.

  • Page 111: Automatic Mode

    Driving Displays in the instrument panel Moving off When the engine is idling with the brakes off, if position R , A or M is When you move the lever, the symbol  To start the engine, place the gear lever in selected, the vehicle will move off corresponding to its position is displayed in the position N .

  • Page 112: Manual Gear Changing

    Manual mode Manual gear changing The gear change requests are only carried out if the engine speed permits. It is not necessary to release the accelerator during gear changes. When braking or slowing down, the gearbox changes down automatically to permit acceleration in the correct gear.

  • Page 113: Sport Setting

    Driving Sport setting Stopping the vehicle Operating fault Before switching off the engine, you can With the ignition on, the  After selection of manual or choose to: flashing of this warning lamp, automated mode, press the S button to switch on the Sport move to position N to engage neutral, accompanied by an audible leave the gear engaged;...

  • Page 114: Gear Shift Indicator

    Gear shift indicator System which reduces fuel consumption by recommending the most appropriate gear. Operation Example: Depending on the driving situation and your vehicle's equipment, the system may advise you to skip one (or more) gear(s). You can follow this instruction without engaging the intermediate gears.

  • Page 115: Tyre Under-Infl Ation Detection

    Driving Tyre under-infl ation detection This system does not avoid the need The tyre pressures for your vehicle can be found on the tyre pressure label (see to check the tyre pressures regularly (including the spare wheel) and before the "Identification markings" section). The tyre pressures must be checked a long journey.
  • Page 116 Under-inflation alert Operating fault The alert is given by the fixed illumination The flashing and then fixed The alert is maintained until the tyre or of this warning lamp, accompanied by illumination of the under-inflation tyres concerned is reinflated, repaired an audible signal, and depending on warning lamp accompanied by the or replaced.

  • Page 117: Stop & Start

    Driving Stop & Start The Stop & Start system puts the engine temporarily into standby - STOP mode - during stops in the traffic (red lights, traffic jams, or other...). The engine restarts automatically - START mode - as soon as you want to move off. The restart takes place instantly, quickly and silently. Perfect for urban use, the Stop &...
  • Page 118 Deactivation Going into engine START mode Special cases: START invoked automatically The "ECO" warning lamp goes off START mode is invoked automatically when: and the engine starts automatically: the driver's door is open, the driver's seat belt is not fastened, with a manual gearbox , when you fully the speed of the vehicle exceeds 15 mph depress the clutch pedal,...

  • Page 119: Maintenance

    Driving Reactivation Operating fault Maintenance Before doing anything under the Press the "ECO OFF" switch again. bonnet, deactivate the Stop & Start The system is active again; this is confirmed system to avoid any risk of injury by the switch warning lamp going off and a resulting from automatic operation of message in the screen.

  • Page 120: Lane Departure Warning System

    Lane departure warning system Activation Operating fault  Press this button, the indicator In the event of a fault, the indicator lamp in the lamp comes on. button flashes. Contact a CITROËN dealer or a qualified workshop. Detection - alert You are warned by the vibration of the driver's The detection may be impeded: seat cushion:...

  • Page 121: Head-Up Display

    Driving Head-up display Displays during operation System which projects information onto a Head-up display on / off. transparent strip in the field of vision of the 2. Display height adjustment. driver so that they do not have to take their 3.

  • Page 122: Activation / Deactivation

    Activation / Deactivation Brightness adjustment We recommend that adjustments are only made using these buttons when the vehicle is stationary. When stationary or while driving, no objects should be placed around the transparent strip (or on its cover) to avoid blocking the strip output and preventing its correct operation.

  • Page 123: Memorising Speeds

    Driving Memorising speeds This memorising of speeds applies to both the speed limiter and the cruise control. You can memorise up to 5 speeds in the system. By default, some speeds are already memorised. With the Audio System With eMyWay Access ...

  • Page 124: Speed Limiter

    Speed limiter Steering mounted controls Displays in the instrument panel System which prevents the vehicle from exceeding the speed programmed by the driver. When the programmed speed limit is reached, pressing the accelerator pedal no longer has any effect. Operation The speed limiter is switched on manually: it requires a programmed speed of at least 20 mph (30 km/h).
  • Page 125 Driving Programming Exiting the speed limiter mode  Turn dial 1 to the "LIMIT" position: the speed limiter mode is selected but is not  Turn dial 1 to the "0" position: the speed switched on (Pause). limiter mode is deselected. It disappears You do not have to switch the speed limiter on from the screen.

  • Page 126: Cruise Control

    Cruise control Steering mounted controls Displays in the instrument panel System which automatically maintains the speed of the vehicle at the value programmed by the driver, without any action on the accelerator pedal. Operation The cruise control is switched on manually: it requires a minimum vehicle speed of 25 mph (40 km/h) and engagement of: fourth gear on a manual gearbox,...
  • Page 127 Driving Programming Operating fault In the event of a cruise control malfunction,  Turn dial 1 to the "CRUISE" position: the the speed is cleared resulting in flashing of the cruise control mode is selected but is not dashes. switched on (Pause). Have it checked by a CITROËN dealer or a ...

  • Page 128: Rear Parking Sensors

    Parking sensors Rear parking sensors The system is switched on by engaging reverse gear. This is accompanied by an audible signal. The system is switched off when you exit reverse gear. This system indicates the proximity of an obstacle (person, vehicle, tree, gate, etc.) which comes within the field of detection of sensors located in the bumper.

  • Page 129: Front Parking Sensors

    Driving Front parking sensors Operating fault Deactivation / Activation of the front and rear parking sensors In addition to the rear parking sensors, the In the event of a malfunction front parking sensors are triggered when an of the system, when reverse obstacle is detected in front and the speed of gear is engaged this warning the vehicle is still below 6 mph (10 km/h).

  • Page 130: Reversing Camera

    Reversing camera A reversing camera is activated automatically The green lines represent the general direction The red lines represent around 30 cm beyond when reverse gear is engaged. of the vehicle. the limit of your vehicle's rear bumper. The The colour image is provided in the navigation audible signal becomes continuous from this screen.
  • Page 131 Visibility...

  • Page 132: Lighting Controls

    Lighting controls System for selection and control of the various front and rear lamps providing the vehicle's lighting and signalling. Main lighting Additional lighting Automatic lighting functions There are various lamps on the vehicle: Other lamps are installed to fulfil the Various automatic lighting functions are also sidelamps, to be seen, requirements of particular driving conditions:...
  • Page 133 Visibility Selection ring for main lighting mode Turn the ring to position the symbol required facing the mark. Lighting off. Automatic illumination of headlamps. Sidelamps only. Dipping the headlamps Dipped or main beam headlamps. Pull the stalk to switch the lighting between dipped / main beam headlamps.

  • Page 134: Front And Rear Foglamps

    Foglamps selection ring The foglamps operate with dipped and main beam headlamps. In good or rainy weather, both day and night, the front foglamps and the rear foglamps are prohibited. In these situations, the power of their beams may dazzle other drivers. They should only be used in fog or snow.
  • Page 135 Visibility Daytime running lamps (LEDs) Lighting left on audible signal An audible signal when a front door is opened warns the driver that the vehicle's exterior lighting is on, with the ignition off and in manual lighting mode. In this case, switching off the lighting stops the audible signal.

  • Page 136: Automatic Illumination Of Headlamps

    Automatic illumination of headlamps Operating fault The sidelamps and dipped beam headlamps are Association with the automatic "Guide-me-home" lighting switched on automatically, without any action on In the event of a malfunction the part of the driver, when a low level of external Association with the automatic lighting provides of the sunshine sensor, light is detected or in certain cases of activation of...
  • Page 137 Visibility Automatic headlamp dipping Switching on Pause If the situation requires a change of headlamp  Put the lighting control stalk ring beam, the driver can take over at any time. in the "AUTO" position.  Press the button, its indicator ...

  • Page 138: Manual Guide-Me-Home Lighting

    Manual guide-me-home Parking lamps lighting The system may suffer interference or not work correctly: under conditions of poor visibility (for example, snowfall, heavy rain or thick fog, ...), if the windscreen is dirty, misted or obscured (by a sticker, ...) in front of the camera, if the vehicle is facing highly reflective signs.

  • Page 139: Exterior Welcome Lighting

    Visibility Exterior welcome Door mirror spotlamps lighting Programming The remote switching on of the lighting makes The lighting duration is selected via your approach to the vehicle easier in poor the vehicle configuration menu. light. It is activated according to the level of light detected by the sunshine sensor.
  • Page 140 Manual adjustment Automatic adjustment of xenon headlamps of halogen headlamps To avoid causing a nuisance to other road In order to avoid causing a nuisance to other If a fault occurs, do not touch the xenon users, the height of the halogen headlamps road users, this system corrects the height of the bulbs.

  • Page 141: Directional Lighting

    Visibility Directional lighting Programming When the dipped or main beam headlamps are on, this function, allows the light beams to better follow the road. The system is activated or The use of this function, coupled with the deactivated in the vehicle xenon headlamps and the cornering lighting, configuration menu.

  • Page 142: Cornering Lighting

    Cornering lighting Switching on This function starts: when the corresponding direction indicator is switched on, from a certain angle of rotation of the steering wheel. Switching off With dipped or main beams, this function with cornering lighting The system does not operate: makes use of the beam from a front foglamp below a certain angle of rotation of the to illuminate the inside of a bend, when the...

  • Page 143: Wiper Controls

    Visibility Wiper controls Manual controls The vehicle's front and rear wipers are designed to improve the driver's visibility The wipers are controlled directly by the driver. progressively according to the climatic conditions. Windscreen wipers Programming Wiping speed: Various automatic wiper control modes are also available according to the following options: fast (heavy rain), automatic rain sensitive windscreen wipers,...

  • Page 144: Rear Wiper

    Rear wiper Windscreen and headlamp wash Rear wiper selection ring: park, intermittent wipe, wash-wipe (set duration). Reverse gear If a significant accumulation of snow  Pull the windscreen wiper stalk towards or ice is present, or when using a When reverse gear is engaged, the rear wiper you.

  • Page 145: Automatic Rain Sensitive Windscreen Wipers

    Visibility Automatic rain sensitive windscreen wipers The windscreen wipers operate automatically, without any action on the part of the driver, if rain is detected (sensor behind the rear view mirror), adapting their speed to the intensity of the rainfall. Switching on Switching off Briefly push the control stalk Briefly push the control stalk...
  • Page 146 Special position of the windscreen wipers Operating fault If a fault occurs with the automatic rain sensitive wipers, the wipers will operate in intermittent mode. Have it checked by CITROËN dealer or a qualified workshop. This position permits release of the windscreen To maintain the effectiveness of the Do not cover the rain sensor, linked with wiper blades.

  • Page 147: Courtesy Lamps

    Visibility Courtesy lamps Front - rear courtesy lamps Front - rear map reading lamps In this position, the courtesy lamp  With the ignition on, press the comes on gradually: corresponding switch. when the vehicle is unlocked, when the electronic key is removed from Take care to avoid leaving anything in the reader, contact with the courtesy lamps.

  • Page 148: Interior Mood Lighting

    Interior mood lighting Footwell lighting The dimmed passenger compartment lighting improves visibility in the vehicle when the light is poor. Switching on Adjusting the brightness of the courtesy lamp The soft lighting provided by the footwell lamps improves visibility in the vehicle when the light is poor.

  • Page 149: Child Safety

    Child safety...
  • Page 150 General points relating to child seats Although one of CITROËN main criteria when designing your vehicle, the safety of your children also depends on you. For maximum safety, please observe the CITROËN recommends that children following recommendations: should travel in the outer rear seats of in accordance with European regulations, your vehicle: all children under the age of 12 or less...
  • Page 151 Child safety Child seat in the front * "Rearward-facing" "Forward-facing" When a "rearward-facing" child seat is installed When a "forward-facing" child seat is installed Passenger seat in the fully back and on the front passenger seat , adjust the seat on the front passenger seat , adjust the highest position.

  • Page 152: Deactivating The Passenger's Airbag

    Deactivating the passenger's airbag The warning label present on both sides of Never install a rearward-facing child the passenger's sun visor repeats this advice. restraint system on a seat protected by In line with current legislation, the following an active front airbag. This could cause two pages contain this warning in all of the the death of the child or serious injury.
  • Page 153 Child safety Child seat at the rear "Rearward facing" "Forward facing" Centre rear seat When a "rearward facing" child seat is installed When a "forward facing" child seat is installed A child seat with a support leg must never be on a rear passenger seat , move the vehicle's on a rear passenger seat , move the vehicle's installed on the centre rear passenger seat .
  • Page 154 Child safety Installing child seats attached using the seat belt In accordance with European regulations, this table indicates the options for installing child seats secured using a seat belt and universally approved (a) according to the weight of the child and the seating position in the vehicle: Weight of the child and indicative age Under 13 kg From 9 to 18 kg...

  • Page 155: "Isofix" Mountings

    "ISOFIX" mountings Your vehicle has been approved in accordance with the latest ISOFIX regulations . The seats, represented below, are fitted with regulation ISOFIX mountings: To secure the child seat to the TOP TETHER : remove and stow the head restraint before installing the child seat on this seat (refit it after the child seat has been removed), open the TOP TETHER cover by pulling its...
  • Page 156 Locations for installing ISOFIX child seats In accordance with European Regulations, this table indicates the options for installing ISOFIX child seats on seats in the vehicle fitted with ISOFIX mountings. In the case of universal and semi-universal ISOFIX child seats, the ISOFIX size category, determined by a letter from A to G , is indicated on the child seat next to the ISOFIX logo.
  • Page 157 Child safety IUF: seat suitable for the installation of an I sofix For advice on securing of the top belt, refer to Remove and stow the head restraint U niversal seat, " F orward-facing" secured the "Isofix mountings" section. before installing a child seat with a using the top belt secured to the upper X: seat not suitable for the installation of a child backrest on a passenger seat.

  • Page 158: Installing A Booster Seat

    Advice on child seats Installing a booster seat The incorrect installation of a child seat in a For optimum installation of the "forward- vehicle compromises the child's protection in facing" child seat, ensure that the back of the event of an accident. the child seat is as close as possible to the The chest part of the seat belt must be Ensure that there is no seat belt or seat belt...

  • Page 159: Electric Child Lock

    Child safety Electric child lock Remote control system to prevent opening of the rear doors using their interior controls and use of the rear electric windows. Any other status of the indicator lamp indicates a fault with the electric child lock.
  • Page 160 Safety...

  • Page 161: Direction Indicators

    Direction indicators Hazard warning lamps Three fl ashes Press the button, the direction indicators flash.  Lower the lighting control stalk fully when They can operate with the ignition off. moving to the left. Move the stalk briefly upwards or downwards, ...

  • Page 162: Emergency Or Assistance Call

    Safety Emergency or Horn assistance call Audible warning system to alert other road users to an imminent danger. This system allows you to make an emergency  Press the central part of the multifunction or assistance call to the emergency services or steering wheel.

  • Page 163: Electronic Stability Programme (Esc)

    Electronic stability programme (ESC) Definitions Electronic Stability Programme incorporating the following systems: Anti-lock braking system (ABS) Anti-slip regulation (ASR) the anti-lock braking system (ABS) and the and electronic brake force electronic brake force distribution (EBFD), The ASR system (also known as Traction distribution (EBFD) the emergency braking assistance, Control) optimises traction in order to avoid...
  • Page 164 Safety Intelligent traction control Operation system ("Snow motion") Anti-lock braking system (ABS) When changing wheels (tyres and rims), Your vehicle has a system to help driving on and electronic brake force make sure that these are approved for snow: intelligent traction control. distribution (EBFD) your vehicle.

  • Page 165: Dynamic Stability Control (Dsc)

    Reactivation Deactivation In exceptional conditions (starting a vehicle The systems are reactivated automatically each which is bogged down, stuck in snow, on soft time the ignition is switched back on or from ground...), it may be advisable to deactivate 30 mph (50 km/h). the DSC and ASR, so that the wheels can turn Below 30 mph (50 km/h), you can reactivate freely and regain grip.
  • Page 166 Safety DSC/ASR After an impact, have these systems The DSC and ASR systems offer increased The correct operation of these systems checked by a CITROËN dealer or a depends on observation of the safety in normal driving, but they should not qualified workshop.

  • Page 167: Front Seat Belts

    Seat belts Front seat belts Rear seat belts Fastening The rear seats are each fitted with a seat belt, three-point anchorages with inertia reel and  Pull the strap, then insert the tongue in the force limiter (except for the centre rear seat). The front seat belts are fitted with a buckle.
  • Page 168 Safety Front seat belt warning lamps On switching on the ignition, warning lamp 1 comes on in the instrument panel and the corresponding warning lamp 2 and/or 3 come(s) on in red in the passenger's seat belt and front airbag warning lamp display if the corresponding seat belt is not fastened or is unfastened.
  • Page 169 Recommendations for children The driver must ensure that passengers use In order to be effective, a seat belt must: the seat belts correctly and that they are all be tightened as close to the body as Use a suitable child seat if the passenger is restrained securely before setting off.

  • Page 170: Front Airbags

    Safety Airbags Front airbags System designed to maximise the safety of the occupants (with the exception of the rear centre passenger) in the event of violent collisions. The airbags supplement the action of the force- limiting seat belts (with the exception of the centre rear passenger).
  • Page 171 According to version, this warning Reactivation lamp comes on either in the When you remove the child seat, with instrument panel or in the seat belt the ignition off , turn the switch to the and passenger's front airbag warning lamp "ON"...

  • Page 172: Lateral Airbags

    Safety Lateral airbags Deployment The curtain airbag is deployed at the same time as the corresponding lateral airbag in the event of a serious side impact applied to all or part of the side impact zone B , perpendicular to the longitudinal centreline of the vehicle on a horizontal plane and directed from the outside towards the inside of the vehicle.
  • Page 173 For the airbags to be fully effective, observe the following safety rules: Front airbags Lateral airbags Sit in a normal upright position. Wear a correctly adjusted seat belt. Do not drive holding the steering wheel by its Use only approved covers on the seats, Do not leave anything between the spokes or resting your hands on the centre compatible with the deployment the lateral...

  • Page 174: Practical Information

    Practical information...

  • Page 175: Temporary Puncture Repair Kit

    Temporary puncture repair kit List of tools Complete system consisting of a compressor and a sealant cartridge which permits All of these tools are specific to your vehicle temporary repair of a tyre so that you can and can vary according to equipment. Do not drive to the nearest garage.
  • Page 176 Practical information Description of the kit The tyre inflation pressures are given on this A. "Sealant" or "Air" position selector. Sealant cartridge. label. B. On "I" / off "O" switch. G. White pipe with cap for repair. C. Deflation button. H.

  • Page 177: Repair Procedure

    Repair procedure 1. Sealing  Uncoil the white pipe G fully.  Connect the compressor's electric plug to  Unscrew the cap from the white pipe. the vehicle's 12 V socket.  Switch off the ignition.  Connect the white pipe to the valve of the ...
  • Page 178 Practical information Tyre under-infl ation detection If the vehicle is fitted with tyre under- inflation detection, the under-inflation warning lamp will remain on after the wheel has been repaired until the system is reinitialised by a CITROËN dealer or a qualified workshop. ...
  • Page 179 2. Infl ation  Connect the compressor's electric plug to  Adjust the pressure using the compressor the vehicle's 12 V socket. (to inflate: switch B in position "I" ; to  Turn the selector A to the "air"  Start the vehicle again and leave the deflate: switch B in position "O"...

  • Page 180: Removing The Cartridge

    Practical information Removing the cartridge Checking tyre pressures / inflating accessories  Stow the black pipe.  Detach the angled base from the white pipe.  Support the compressor vertically.  Unscrew the cartridge from the bottom. You can also use the compressor, without ...

  • Page 181: Changing A Wheel

    Changing a wheel Access to the tools Procedure for changing a faulty wheel for the spare wheel using the tools provided with the vehicle * . Tyre under-infl ation detection The spare wheel is not fitted with a sensor. The punctured wheel must be repaired by a CITROËN dealer or a qualified workshop.
  • Page 182 Practical information Access to the spare wheel List of tools * All of these tools are specific to your vehicle and can vary according to the level of equipment. Do not use them for other purposes. Wheelbrace. For removing the wheel trim and removing the wheel bolts.

  • Page 183: Taking Out The Spare Wheel

    Taking out the spare wheel  Raise the floor to reveal the spare wheel  Detach the assembly of wheel and box  Press the tongue, slide the cover of the box carrier drive nut. from the rear of the vehicle. to mid travel then remove it for access to ...
  • Page 184 Practical information Putting the spare wheel back in place  Stow the jack in the box and refit the  Raise the assembly of wheel and box  Tighten fully and check that the wheel is covers. underneath the vehicle by turning the horizontally flush against the floor.

  • Page 185: Removing A Wheel

    Removing a wheel Parking the vehicle Immobilise the vehicle where it does not block traffic: the ground must be level, stable and not slippery. Apply the parking brake unless it has been programmed to automatic mode, switch off the ignition and engage first gear * to block the wheels.
  • Page 186 Practical information  Place the jack 2 in contact with one of the  Extend the jack 2 until its base plate is in  Raise the vehicle until there is sufficient two front A or rear B locations provided on contact with the ground.

  • Page 187: Fitting A Wheel

    Fitting a wheel Fitting the "space-saver" spare wheel If your vehicle is fitted with alloy wheels, when tightening the bolts on fitting, it is normal to notice that the washers do not come into contact with the "space-saver" spare wheel. The wheel is secured by the conical surface of each bolt.
  • Page 188 Practical information  Lower the vehicle fully.  Tighten the security bolt using the  Fold the jack 2 and detach it. wheelbrace 1 fitted with the security socket 5 .  Tighten the other bolts using the wheelbrace 1 only. ...

  • Page 189: Snow Chains

    Snow chains In wintry conditions, snow chains improve traction as well as the behaviour of the vehicle when braking. Advice on installation Use only the chains designed to be fitted to the The snow chains must be fitted only type of wheel fitted to your vehicle: ...

  • Page 190: Changing A Bulb

    Practical information Changing a bulb Front lamps Model with xenon headlamps Main beam headlamps (H1-35W). 2. Directional dipped / directional Risk of electrocution headlamps (D1S-35W). Xenon bulbs (D1S-35W) must be 3. Daytime running lamps / sidelamps replaced by a CITROËN dealer or a (light emitting diodes - LEDs).

  • Page 191: Dipped Beam Headlamps

    The headlamps are fitted with polycarbonate glass with a protective coating:  do not clean them using a dry or abrasive cloth, nor with a detergent or solvent product,  use a sponge and soapy water or a pH neutral product, ...
  • Page 192 Practical information Main beam headlamps Dipped beam headlamps (halogen model) (halogen model)  Remove the protective plastic cover by  Remove the protective plastic cover by  Press on the top of the connector then pulling on the tab. pulling on the tab. pivot the assembly downwards.

  • Page 193: Daytime Running Lamps / Sidelamps

    Daytime running lamps / sidelamps Direction indicators For the replacement of this type of LED lamp For reassembly, carry out these operations in Faster flashing of a direction indicator and lighting guides, contact a CITROËN dealer reverse order. warning lamp (left or right) indicates a or a qualified workshop.

  • Page 194: Front Fog Lamps

    Practical information Door mirror spotlamps Integrated direction indicator Front foglamps side repeaters You should contact a CITROËN dealer or a You should contact a CITROËN dealer or a  Remove the deflector under the body. qualified workshop for the replacement of the qualified workshop for the replacement of these ...

  • Page 195: Rear Lamps

    Rear lamps Direction indicators and brake Sidelamps lamps (on the wings) (light emitting diodes - LEDs). 2. Direction indicators (PY21W amber).  Open the boot then remove the access  Carefully remove the lamp unit from 3. Reversing lamps (P21W). cover.
  • Page 196 Practical information Reversing lamp (tailgate) Foglamp  Open the tailgate.  Carefully remove the lamp from the Access is by passing a hand under the bumper.  Turn the bulb holder a quarter of a turn and  Unclip the skirt of the lamp. outside.

  • Page 197: Number Plate Lamps

    Third brake lamp Number plate lamps (light emitting diodes - LEDs)  Insert a thin screwdriver into the slot Contact a CITROËN dealer or qualified in the lens. workshop.  Push it outwards to unclip it.  Remove the lens. ...

  • Page 198: Changing A Fuse

    Practical information Changing a fuse Procedure for replacing a failed fuse with a new fuse to rectify a failure of the corresponding function. Access to tooling Changing a fuse Installing electrical accessories Your vehicle's electrical system is designed to operate with standard or optional equipment.

  • Page 199: Dashboard Fuses

    Dashboard fuses Fuse Rating Functions N° The fusebox is placed in the lower dashboard F6 A or B Audio system. (left-hand side). Alarm. Front cigarette lighter, front 12 V socket. Rear 12 V socket. Rear map reading lamps. Courtesy mirror. F28 A or B Audio system.

  • Page 200: Engine Compartment Fuses

    Practical information Engine compartment fuses Fuse Rating Functions N° Front / rear screenwash pump. Headlamp wash pump. Horn. Right-hand main beam headlamp. Left-hand main beam headlamp. Left hand lamp mask. Right hand lamp mask. The fusebox is placed in the engine compartment near the battery.

  • Page 201: Access To The Battery

    12 V battery Procedure for starting the engine using another battery or charging a discharged battery. Access to the battery The presence of this label, in particular with the Stop & Start system, indicates the use of a 12 V lead-acid battery with Disconnecting the (+) cable special technology and specification;...

  • Page 202: Starting Using Another Battery

    Practical information Starting using another Charging the battery using battery a battery charger When your vehicle's battery is discharged, With Stop & Start, the battery does not the engine can be started using a slave battery have to be disconnected for charging. (external or on another vehicle) and jump lead cables.
  • Page 203 Before disconnecting the battery Protect your eyes and face before Some functions are not available if the Wait 2 minutes after switching off the ignition handling the battery. battery is not sufficiently charged. before disconnecting the battery. All operations on the battery must be Close the windows and the doors before carried out in a well ventilated area and disconnecting the battery.

  • Page 204: Load Reduction Mode

    Practical information Load reduction mode Energy economy mode Exiting economy mode System which manages the use of certain System which manages the duration of use of functions according to the level of charge certain functions to conserve a sufficient level These functions are reactivated automatically remaining in the battery.

  • Page 205: Changing A Wiper Blade

    Changing a wiper blade Before removing a front Fitting wiper blade  Put the corresponding new wiper blade in place and clip it.  Within one minute after switching off  Fold down the wiper arm carefully. the ignition, operate the wiper stalk to position the wiper blades vertically on the windscreen.

  • Page 206: Towing The Vehicle

    Practical information Towing the vehicle Towing your vehicle Towing another vehicle Procedure for having your vehicle towed or for towing another vehicle using a removable towing eye. Access to the tools  On the front bumper, unclip the cover by ...

  • Page 207: Towing A Trailer

    Towing a trailer Towbar suitable for the attachment of a trailer We recommend the use of genuine Driving with a trailer places greater or installation of a bicycle carrier, CITROËN towbars and their harnesses demands on the towing vehicle and the with additional lighting and signalling.
  • Page 208 Practical information Driving advice Distribution of loads Cooling Braking  Distribute the load in the trailer so that the Towing a trailer on a slope increases the Towing a trailer increases the braking distance. heaviest items are as close as possible to temperature of the coolant.

  • Page 209: Fitting Roof Bars

    Fitting roof bars When fitting transverse roof bars, take care to Maximum authorised load evenly Use accessories recommended by position them correctly: distributed on the roof bars, for a CITROËN observing the manufacturer's loading height not exceeding 40 cm recommendations and fitting (with the exception of bicycle carriers): instructions so as to avoid the risk 70 kg.
  • Page 210 Checks...

  • Page 211: Opening The Bonnet

    Checks Opening the bonnet Before doing anything under the bonnet, switch off the Stop & Start system to avoid any risk of injury resulting from an automatic change to START mode. Because of the presence of electrical equipment under the bonnet, it is recommended that exposure to water Opening (rain, washing, ...) be limited.

  • Page 212: Petrol Engines

    Petrol engines The various caps and covers allow access for checking the levels of the various fluids and for replacing certain components. Power steering reservoir. 2. Screenwash and headlamp wash reservoir. 3. Coolant reservoir. 4. Brake fluid reservoir. 5. Battery / Fuses. 6.

  • Page 213: Diesel Engines

    Checks Diesel engines The various caps and covers allow access for checking the levels of the various fluids, for replacing certain components and for priming the fuel system. Power steering reservoir. 2. Screenwash and headlamp wash reservoir. 3. Coolant reservoir. 4.

  • Page 214: Running Out Of Fuel (Diesel)

    Running out of fuel (Diesel) 1.6 litre HDi engine 2 litre HDi engine On vehicle fitted with HDi engines, the fuel system must be primed if you run out of fuel; refer to the corresponding engine compartment view.  Fill the fuel tank with at least five litres ...

  • Page 215: Checking Levels

    Checks Checking levels Check all of these levels regularly, in line with the maintenance and warranty guide. Top them up if necessary, unless otherwise indicated. If a level drops significantly, have the corresponding system checked by a CITROËN dealer or a qualified workshop. Take care when working under the bonnet, as certain areas of the engine may be extremely hot (risk of burns) and the cooling fan could start at any time (even with the ignition off).

  • Page 216: Engine Oil Change

    Brake fluid level Topping up the engine oil level Engine oil change The brake fluid level should be close Oil grade Refer to the maintenance and warranty guide to the "MAX" mark. If it is not, check The oil must be the correct grade for your for details of the interval for this operation.

  • Page 217: Coolant Level

    Checks Coolant level Screenwash / headlamp wash level The coolant level should be close to the "MAX" mark but should never exceed it. When the engine is warm, the temperature of the coolant is regulated by the fan.  Take and pinch the level gauge to block its The cooling fan may start after switching breather.

  • Page 218: Used Products

    Diesel additive level Used products (Diesel engine with particle emission filter) Avoid prolonged contact of used oil or fluids with the skin. A low additive level is Most of these fluids are harmful to indicated by illumination of health or indeed very corrosive. the service warning lamp, accompanied by an audible warning and a message in the instrument panel screen.
  • Page 219 Checks Checks 12 V battery Unless otherwise indicated, check these components in accordance with the The battery does not require any maintenance and warranty guide and according maintenance. to your engine. However, check that the terminals are clean and correctly tightened, Otherwise, have them checked by a CITROËN particularly in summer and winter.

  • Page 220: Oil Filter

    Air filter and passenger compartment filter Particle emission filter (Diesel) Manual gearbox Refer to the maintenance and The start of saturation of the The gearbox does not require any warranty guide for details of the particle filter is indicated by maintenance (no oil change).

  • Page 221: Brake Pads

    Checks Brake pads Electric parking brake Brake wear depends on the style of driving, particularly in the case This system does not require any Only use products recommended by of vehicles used in town, over short routine servicing. However, in the CITROËN or products of equivalent distances.

  • Page 222: Technical Data

    Technical data...

  • Page 223: Dimensions (In Mm)

    Technical data Dimensions (in mm)
  • Page 224 This handbook describes all of the equipment Automobiles CITROËN declares, by application available in the whole range. of the provisions of the European regulation (Directive 2000/53) relating to End of Life Vehicles, Your vehicle will be fi tted with some of this that it achieves the objectives set by this regulation equipment described in this document, depending and that recycled materials are used in the...
  • Page 225 13DS5.0040 Anglais...

Table of Contents