Table of Contents
Advertisement
ID
19
OPERATION
No.
ID
21 l-3
: Work on the distributor
Op.ID
211-3
115
13
14
15
16
17
18
19
20
21
22
23
24
Place
on
the
contact
support
(23),
the
insulating
washer
(24),
the
contact
(22),
fitting
the
contact
spring
between
the
support
(23)
and
the
terminal
of the
primary
wire.
Tighten
the
nut.
Attach
terminal
(20)
to
the
contact
support
(23)
and
tighten
screw
(25)
(spring
washer
under
the
head).
Place
the
flat
ring
(19)
on
the
plate.
Oil
the
spindle
and
place
it
in
the
body
of the
distributor,
using
two
adjusting
washers.
Fit
the
dog
(6).
Make
sure
that
the
hole
for
pin
(5)
in
the
shaft
is
off-set.
Between
the
dog
and
the
distributor
insert
an
adjusting
washer
(7).
Place
the'pin
(5)
in
position
temporarily.
Make
sure
that
the
spindle
turns
freely
and
that
the
longitudinal
play
does
not
exceed
0.4
mm.
If it
does
then
use
another
adjusting
washer
Drive
in
the
pin
(5)
and
place
the
pin
retaining
spring
(4)
in
position.
Make
sure
that
the
direction
of the
winding
of
the
spring
(4)
is left
hand
(see
fig.
2).
If
not,
turn
the
spring
round
to
reverse
the
direction
of winding.
Place
the
friction
washer
on
spindle.
Place
the
cam
(18)
in
position;
with
the
small
side
of the
dog
towards
the
operator,
the
groove
in
the
cam
will
be
on
the
right.
Fit
the
rollers
(17),
the
smaller
end
upwards.
Fit
the
springs
(15)
of the
advance
weights
(16).
Place
the
contact
support
plate
assembly
(12)
in
the
distributor
body
on
the
ring
(14).
(Oil
the
balls
first
with
Vaseline
oil).
Connect
the
earth
lead
by
means
of
screw
(26).
Fit
the
pilot
rod
(lo),
the
diaphragm
control
rod
(9)
and
the
retainer
ring
on
the
support
plate
driving
peg.
Fit
the
primary
terminal
(3),
the
primary
contact
strip
(l),
the
primary
wire
to
the
coil
and
the
condenser
(2).
Connect
the
vacuum
diaphragm
(8)
to
the
control
rod
(9)
and
tighten
the
diaphragm
fixing
screws
(spring
washers
under
heads).
Fit
the
distributor
cover
retaining
springs
(27),
adjust
the
nuts
(28)
to make
contact
with
the
flat
ring
(19).
Make
sure
that
the
contact
support
plate
assembly
(12)
can
rotate.
Adjust
the
distance
between
the
contact
points
to
0.4
mm
by
turning
the
eccentric
screw
(29).
Tighten
the
locking
screw.
Connect
the
wires
on
the
cover
of
the
distributor.
Place
the
rotor
on the
cam,
make
sure
that
the
lug
is
correctly
engaged
in
the
groove
in
the
cam.
Refit
the
cover
of
the
distributor.
Bench
test
the
distributor
(see
Op.
ID
211-O).
TOOLS
- Quick Links:
- Electrical
- Starter Motor
Hide quick links:
Advertisement
Table of Contents
