Page 2 On-line owner's handbook You can ﬁ nd your handbook on the CITROËN website, under Referring to the owner's handbook on-line also gives you "MyCitroën". access to the latest information available, easily identiﬁ ed by the bookmark, associated with this symbol: This personal and customisable space allows you to establish direct and special contact with CITROËN.
Page 3 Happy motoring! This key will enable you to identify the special features of your vehicle: C4 Picasso Grand C4 Picasso Grand C4 Picasso with 5 seats Grand C4 Picasso with 7 seats...
Page 4: Distance Alert
Familiarisation Exterior Electronic key: Keyless Distance alert Entry and Starting Using a radar located at the front of the vehicle, this system provides: the Display of the inter-vehicle time , to help the driver maintain a safe distance between their vehicle and the one in front, the triggering of a Collision risk alert, to warn the driver, in certain driving conditions, that their vehicle is at risk of collision with the vehicle in front.
Page 5: Automatic Headlamps
Familiarisation Exterior Stop & Start This system puts the engine temporarily into standby during stops in the traffic (traffic lights, traffic jams, etc...). The engine restarts automatically as soon as you want to move off. The Stop & Start system reduces fuel consumption and exhaust emissions, as well as noise levels when stationary.
Page 6: Reversing Camera
Familiarisation Exterior Reversing camera 360 Vision This system is activated automatically on This system provides an image in the engaging reverse and provides an image in the instrument panel of the near surroundings of instrument panel. your vehicle, using cameras located at the front and rear of the vehicle and under the door mirrors.
Page 7: Under-Inflation Detection
Familiarisation Exterior Motorised tailgate Blind spot sensors This system simplifies the opening and closing In certain driving conditions, this system of the boot by means of motorisation of the detects the presence of vehicles in the blind tailgate. spots. You are alerted by the illumination of a warning lamp in the corresponding mirror.
Page 8: Keyless Entry And Starting
Familiarisation Access Electronic key - Remote Keyless Entry and Starting Motorised tailgate control This system allows the tailgate to be opened remotely using motorisation. The motorisation of the tailgate can be activated or deactivated. Ensure that there is enough space behind the vehicle for the movement of the tailgate.
Page 9: Panoramic Sunroof
Familiarisation Interior Panoramic sunroof 7-inch touch screen tablet This glazed roof increases the light in the It provides access to the heating and air passenger compartment. It is fitted with an conditioning controls, to settings for vehicle electric blind. systems, to controls for the audio, navigation and telematic systems and to the display configuration settings...
Page 10 Familiarisation Interior Bonnet release lever. 2. Fusebox. 3. Steering wheel adjustment controls. 4. Door mirror controls. Electric window controls. 5. Side adjustable air vents. Side window demisting vents. 6. Quarter light demisting windows. Driver's airbag. Horn. 8. Courtesy lamp and map reading lamps. Panoramic glass roof panel blind control.
Page 11: Instruments And Controls
Familiarisation Instruments and controls Headlamp height adjustment. 2. Deactivation of volumetric alarm monitoring, or Ticket holder. 3. Lighting and direction indicator stalk 4. Steering mounted controls (6-speed electronic gearbox system/automatic gearbox). 5. Speed limiter / cruise control / active cruise control controls.
Page 12: Sitting Comfortably
Familiarisation Sitting comfortably Driver's seat Manual adjustments Adjustment of the backrest angle of the driver's seat. 2. Adjustment of the cushion height of the driver's seat. 3. Forwards-backwards adjustment. Electric adjustments Adjustment of the cushion angle and height, and forwards-backwards position. 2.
Page 13: Head Restraint Adjustment
Familiarisation Sitting comfortably Head restraint adjustment Steering wheel adjustment Correct driving position To raise it, pull it upwards. Release. Before taking to the road, adjust in the following To lower it, press on the lug A and on the head 2.
Page 14: Door Mirrors
Familiarisation Sitting comfortably Door mirrors Rear view mirror Adjustment Manual day/night model A. Selection of the mirror to adjust. Selection of the "day" position of the mirror. B. Adjustment of the mirror position in four 2. Adjustment of the mirror. directions.
Page 15: Front Seat Belts
Familiarisation Sitting comfortably Front seat belts Centre rear seat belt in the Outer rear seat belts row (fastening) (stowing) Guide the belt in and place the tongue on the Pull the webbing and insert the tongue A in magnet of the outer anchorage. the right hand buckle.
Page 16: Seeing Clearly
Familiarisation Seeing clearly Lighting Wipers Ring A Stalk A: windscreen wipers Switching on "AUTO" Fast wipe. Press the stalk downwards. Lighting off/daytime running lamps. Normal wipe. Automatic illumination of headlamps. Int. Intermittent wipe. Switching off "AUTO" Sidelamps. Off. Press the stalk downwards again or place AUTO Automatic wiping.
Page 17: Passenger Safety
Familiarisation Passenger safety Passenger's front airbag Seat belt warning lamps Manual child lock A. Warning lamp for not fastened (front seat belts) and unfastened (all seat belts). B. Seat belt location indicator. This manual device prevents opening of the rear doors by the interior door handles. The control is located on the edge of each rear door.
Page 18: Driving Safely
Familiarisation Driving safely Operation Use the buttons arranged on each side of the touch screen tablet for access to the menus, then press on the virtual buttons in the touch screen tablet. From the primary page, use this button for access to the secondary page.
Page 19: Starting The Engine
Familiarisation Driving safely Starting the engine Switching off the engine With the electronic key Immobilise the vehicle. Place the gear selector lever at N for vehicles with an electronic gearbox, P or N for vehicles with an automatic gearbox or neutral for vehicles with a manual gearbox.
Page 20 Familiarisation Driving safely Electric parking brake Manual application / release Automatic application / release Manual application of the parking brake is Before leaving the vehicle, check that First ensure that the engine is running possible by briefly pulling the control lever. the brake warning lamp in the instrument and the driver's door is properly closed.
Page 21: Speed Electronic Gearbox
Familiarisation Driving safely 6-speed electronic gearbox Automatic gearbox system Gear selector positions Gear selector positions Reverse. Park. Neutral. Reverse. Automated mode. Neutral. Manual mode Automatic mode. Using the steering-mounted control paddles "A" A Manual mode. and " B": Using the steering-mounted control paddles "A " A changing gear in manual mode, and "B ": temporarily taking control in automated...
Page 22 Familiarisation Driving safely Stop & Start Going into engine STOP mode Going into engine START mode The "ECO" warning lamp comes on in The "ECO" warning lamp goes off the instrument panel and the engine and the engine restarts automatically: automatically goes into standby: with a manual gearbox, when you fully with a manual gearbox , at speeds below...
Page 23 Familiarisation Driving safely Steering wheel with integrated controls Controls for speed limiter / cruise Other controls Audio system controls control / active cruise control Black panel (black screen). Audio system and telephone 168, 171, 174 2. Control of the display mode of the type 2 controls instrument screen.
Page 24: Eco-Driving
Familiarisation Eco-driving Eco-driving is a range of everyday practices that allow the motorist to optimise their fuel consumption and CO emissions. Optimise the use of your gearbox Control the use of your electrical equipment With a manual gearbox, move off gently and change up without waiting. Before moving off, if the passenger compartment is too warm, ventilate it During acceleration change up early.
Page 25 Familiarisation Limit the causes of excess consumption Observe the recommendations on maintenance Spread loads throughout the vehicle; place the heaviest items in the Check the tyre pressures regularly, when cold, referring to the label in bottom of the boot, as close as possible to the rear seats. the door aperture, driver's side.
Page 26: Inch Touch Screen Tablet
Monitoring 7-inch touch screen tablet General operation The 7-inch touch screen tablet gives access to: the heating/air conditioning controls, Recommendations Principles menus for adjusting settings for vehicle functions and systems, It is necessary to press firmly, particularly for Use the buttons on either side of the screen audio and display configuration menus, "flick"...
Page 27 Monitoring Touch screen tablet menus State of indicator lamps Some buttons contain an indicator lamp that gives the state of the corresponding function. Green indicator: you have switched on the corresponding function. Orange indicator: you have switched off the corresponding function. Access the the "Air conditioning"...
Page 28 Monitoring "Driving assistance" menu The functions with settings that can be adjusted are detailed in the table below. Button Corresponding function Comments Speed settings Memorisation of speeds for use with the speed limiter or cruise control. Under-inflation initialisation Reinitialisation of the under-inflation system. Park Assist Activation of the Park Assist function.
Page 29 Monitoring Button Corresponding function Comments Vehicle settings Access to other functions with settings that can be adjusted. The functions are grouped together under three tabs: " Driving assistance " ● "Automatic rear wiper in reverse" (Activation of rear wiper linked to reverse gear; see the "Visibility"...
Page 30 Monitoring Button Corresponding function Comments Diagnostic List of current alerts. Lane departure warning system Activation of the function. Parking sensors Deactivation of the function. Inter-vehicle time Activation of the function. Automatic headlamp dipping Activation of the function.
Page 31: Configuration Menu
Monitoring "Conﬁ guration" menu The functions available through this menu are detailed in the table below. Button Corresponding function Comments Audio settings Adjustment of volume, balance... Colour schemes Choice of a colour scheme. Interactive help Simplified instructions. Turn off screen Turns the screen off.
Page 32 Monitoring Button Corresponding function Comments System settings Choice of units: temperature (°Celsius or °Fahrenheit) distance and fuel consumption (l/100 km, mpg or km/l). Time/Date Setting the date and time. Languages Choice of language used (for the touch screen tablet and the type 2 instrument panel): French, English, Italian, Spanish, German, Dutch, Portuguese, Polish, Turkish, Russian.
Page 33: Control Buttons
Monitoring Type 1 instrument panel Dials and screens Control buttons Rev counter (x 1 000 rpm or tr/min), 5. Fuel gauge. A. Main lighting dimmer buttons. graduation according to engine (petrol or 6. Service indicator, then total mileage B. Recall servicing information. Diesel).
Page 34: Control Button
Monitoring Type 2 instrument panel This instrument panel is presented in the form of a 12-inch panoramic HD screen. It can be personalised. Depending on the display mode selected, some information can be hidden (see "Personalisation of the instrument panel"). Dials and screens Control button Rev counter (x 1000 tr/min or rpm)
Page 35: Display Zones
Monitoring Display zones Personalisation of the type 2 instrument panel Choosing the display mode instrument panel, by choosing: Each mode corresponds to the type of a colour scheme, information displayed in the configurable area. a display mode. Choosing a colour scheme It depends on the colour scheme chosen for the touch screen tablet.
Page 36 Monitoring "MEDIA": display of information related to "NAVIGATION": display of information "PHOTOS": display of the photo selected the media being played or the radio. related to the navigation in progress (map in the "Media" menu of the touch screen and instructions). tablet.
Page 37 Monitoring "DRIVING": used for the display of the To modify the display mode of the instrument once the selected display mode appears inter-vehicle time and information related to panel: in the central window, press the wheel to the active cruise control. turn the wheel on the left of the steering confirm your choice.
Page 38: Indicator And Warning Lamps
Monitoring Indicator and warning lamps Visual indicators informing the driver that a Associated warnings Certain warning lamps may come on in system is in operation, switched off or has a The switching on of certain warning lamps may one of two modes: fixed (continuous) or fault.
Page 39: Operation Indicator Lamps
Monitoring Operation indicator lamps If one of the following indicator lamps comes on in the instrument panel, this confirms that the corresponding system has come into operation. Warning / indicator lamp State Cause Action / Observations Left-hand direction flashing with buzzer. The lighting stalk is pushed down.
Page 40 Monitoring Warning / indicator lamp State Cause Action / Observations Automatic fixed. The lighting control stalk is in the The camera, located in the door mirror, manages the "AUTO" position, pulled towards headlamp operation of main beam, depending on the ambient you, and the function is activated dipping lighting and driving conditions.
Page 41 Monitoring Warning / indicator lamp State Cause Action / Observations Diesel engine fixed. The "START/STOP" switch has been Wait until the warning lamp goes off before starting. Once it goes off, starting is immediate, on condition pre-heating pressed (ignition on). that you maintain pressure on the brake pedal for an electronic or automatic gearbox, or the clutch pedal is pressed fully down for a manual gearbox.
Page 42 Monitoring Warning / indicator lamp State Cause Action / Observations Automatic fixed. The wiper control is pushed Automatic front wiping is activated. wiping downwards. To deactivate automatic wiping, operate the control stalk downwards or put the stalk into another position. Passenger fixed.
Page 43 Monitoring Deactivation indicator lamps If one of the following indicator lamps comes on, this confirms that the corresponding system has been switched off intentionally. This is may be accompanied by an audible signal and the display of a message. Warning / indicator lamp State Cause Action / Observations...
Page 44: Warning Lamps
Monitoring Warning lamps When the engine is running or the vehicle is being driven, illumination of one of the following warning lamps indicates a fault which requires action on the part of the driver. Any fault resulting in the illumination of a warning lamp must be investigated further using the associated message. If you encounter any problems, contact a CITROËN dealer or a qualified workshop.
Page 45 Monitoring State Cause Action / Observations Service on temporarily. A minor fault has occurred for which Identify the fault by means of the associated message, such as: there is no specific warning lamp. opening of a door, the boot or bonnet, low engine oil level, low screenwash/headlamp wash fluid level, discharged remote control battery,...
Page 46 Monitoring Warning / indicator lamp State Cause Action / Observations Electric parking flashing. When driving: the electric parking Fully release the parking brake by a quick press on the brake brake is not fully released. control lever. If the warning persist, stop as soon as it is safe to do so.
Page 47 Monitoring Warning / indicator lamp State Cause Action / Observations Braking fixed. The braking system fluid level has You must stop as soon as it is safe to do so. dropped significantly. Top up with brake fluid listed by CITROËN. If the problem persists, have the system checked by a CITROËN dealer or a qualified workshop.
Page 48 Monitoring Warning / indicator lamp State Cause Action / Observations Low fuel level fixed, accompanied by When it first comes on there remains You must refuel as soon as possible to avoid running an audible signal and approximately 6 litres of fuel in the out of fuel.
Page 49 Monitoring Warning / indicator lamp State Cause Action / Observations Directional flashing. The directional headlamps system Have it checked by a CITROËN dealer or a qualified headlamps has a fault. workshop. Door(s) open * fixed, associated with A door or the boot is still open. Close the door or boot.
Page 50 Monitoring Warning / indicator lamp State Cause Action / Observations Under-inflation fixed. The pressure in one or more wheels Check the pressure of the tyres as soon as possible. is too low. This check should preferably be carried out when the tyres are cold.
Page 51: Service Indicator
Monitoring Service indicator Between 600 miles (1 000 km) Less than 600 miles (1 000 km) System which informs the driver when the and 1 800 miles (3 000 km) remain remain before the next service is due next service is due, in accordance with the before the next service is due manufacturer's servicing schedule.
Page 52 Monitoring Service overdue Retrieving the service information For 5 seconds after the ignition is switched on, the spanner flashes to indicate that the service You can access the service information at any must be carried out as soon as possible. time.
Page 53: Engine Oil Level Indicator
Monitoring Engine oil level indicator System which informs the driver whether the engine oil level is correct or not. This information is indicated for a few seconds when the ignition is switched on, after the service information. Oil level correct Oil level indicator fault This is indicated by a message in the This is indicated by a message in the...
Page 54: Total Distance Recorder
Monitoring Distance recorders The total and trip distances are displayed for thirty seconds when the ignition is switched off, when the driver's door is opened and when the vehicle is locked or unlocked. To conform to legislation in the country you are crossing, change the units of distance (miles or km) via the configuration menu.
Page 55: Touch Screen Tablet
Monitoring Allows the manual adjustment of the brightness of the instrument panel and touch screen tablet to suit the ambient light level. Operates only when the vehicle lighting is on, with the exception of the daytime running lamps. Two buttons Touch screen tablet With the headlamps on, press button B to Press on the "Configuration"...
Page 56 Monitoring Black screen (black panel) Black screen (touch screen tablet) instrument panel to be switched off for night driving. The instrument panel remains on with the vehicle speed, the gear selected in an electronic or automatic gearbox, cruise control or speed limiter information, if in use, and the low fuel alerts as appropriate.
Page 57: Setting The Date And Time
Monitoring Setting the date and time Select the "Configuration" menu. Select "Adjust time " or " Adjust date" and Press "Confirm " to quit. modify the settings using the number pad, then confirm. From the secondary page, select "Time/Date".
Page 58: Trip Reset
Monitoring Trip computer Type 1 instrument panel System that gives you information on the journey in progress (range, fuel consumption…). The information is accessible in the " Driving assistance " menu. Information display in the touch screen tablet Trip reset The current fuel consumption tab with: ●...
Page 59 Monitoring Trip computer Type 2 instrument panel Information display in the instrument panel Trip reset The display of trip computer information is permanent when you select the "DIALS" display mode. The current information tab with: When the trip required is displayed, press ●...
Page 60: Average Fuel Consumption
Monitoring Trip computer, a few definitions Range Current fuel consumption Distance travelled (miles or km) (mpg or l/100 km or km/l) (miles or km) The distance which can still be Calculated over the last few seconds. Calculated since the last trip travelled with the fuel remaining computer reset.
Page 61: Electronic Key Remote Control
Access Electronic key Remote control Unlocking the vehicle Unlocking the vehicle and opening the boot Complete unlocking Make a long press on this button to unlock the vehicle Press this button. and, depending on version, release the tailgate or open the motorised tailgate.
Page 62: Locking The Vehicle
Access Locking the vehicle Normal locking Press this button. If a door or the boot is not properly The automatic folding and unfolding Holding the button allows the closed, locking does not take place. of the door mirrors can be deactivated windows to be raised to the Nevertheless, the alarm (if fitted) will be by a CITROËN dealer or a qualified...
Page 63: Locating Your Vehicle
Access Locating your vehicle Deadlocking This function allows you to identify your vehicle from a distance, particularly in poor light. Your Deadlocking renders the interior door vehicle must be locked. controls inoperative. It also deactivates the manual central Press this button. locking button.
Page 64: "Keyless Entry And Starting" System
Access "Keyless Entry and Starting" system Unlocking the vehicle Selective unlocking To unlock only the drivers door, with the electronic key on your person, pass your hand behind the driver's door handle. Pull the door handle to open. To unlock the complete vehicle, pass your hand behind one of the door handle of the front passenger door with the electronic key close to the passenger door, or...
Page 65 Access Locking the vehicle Normal locking With the electronic key in the defined Ensure that nothing could prevent the zone A , press with a finger or thumb on correct operation of the windows. one of the door handles (at the markings) Be aware of children when operating or press the locking button on the tailgate.
Page 66 Access By the doors: Deadlocking renders the interior door With the electronic key in the defined controls inoperative. zone A, press a finger or thumb on one of It also deactivates the manual central the front door handles (at the markings) or control button.
Page 67 Access As a safety measure (children on If one of the doors or the boot is still In order to preserve the battery in the board), never leave the vehicle without open or if the electronic key for the electronic key and the vehicle's battery, taking the key for the Keyless Entry and Keyless Entry and Starting system has the "Hands-free"...
Page 68: Emergency Procedure
Access Emergency procedure Emergency unlocking/locking using the integral key Unlocking The integral key is used to lock and unlock the Depending on your version, the vehicle when the electronic key cannot operate direction indicators flash for a few Turn the key towards the front of the vehicle and in the event of a fault with the Keyless seconds, the door mirrors unfold and to unlock the vehicle.
Page 69 Access Normal locking Depending on your version, the direction indicators flash for a Turn the key towards the rear of the vehicle few seconds, the door mirrors fold. to lock the vehicle completely. Deadlocking Turn the key towards the rear in the driver's If your vehicle has an alarm, this door lock to lock the vehicle completely.
Page 70 Access Remote control problem - reinitialisation Following disconnection of the vehicle battery, Changing the battery of the Do not throw the remote control replacement of the remote control battery or electronic key batteries away, they contain metals in the event of a remote control malfunction, which are harmful to the environment.
Page 71: Electrical Interference
Access Visit a CITROËN dealer with the vehicle's registration document and your personal identification documents and if possible the key code label. The CITROËN dealer will be able to retrieve the key code and the transponder code required to order a new key. Electronic key The electronic key is a sensitive system;...
Page 72: Central Locking
Access Central locking Manual central Automatic central locking locking of doors (anti-intrusion security) The doors and boot lock automatically when When locking / deadlocking from the driving, as soon as the speed exceeds 6 mph outside (10 km/h). If the vehicle is locked or deadlocked To activate or deactivate this function (activated from the outside, the button is not by default):...
Page 73: From Outside
Access Doors Opening Closing If a door is not properly closed: with the engine running , this warning lamp and a message appear in the instrument panel (type 1) for a few seconds, when driving (speed above 6 mph (10 km/h)), this warning lamp and a message, accompanied by an audible signal, appear in the instrument...
Page 74: Back-Up Control
Access Back-up control System allowing the doors to be locked and unlocked manually in the event of a malfunction of the central locking system or battery failure. Locking the front and rear Unlocking the front and rear passenger doors passenger doors Open the doors.
Page 75: Opening The Tailgate
Access Boot Opening the tailgate Closing the tailgate With the electronic key / Lower the tailgate using the interior remote control grips. Release the grips and press down on the outside of the tailgate to close it. Make a long press on this button to release the tailgate.
Page 76: Motorised Tailgate
Access Motorised tailgate Tailgate controls A: Exterior control Never place a finger in the tailgate locking system: risk of a serious accident! To avoid the risk of injury, ensure that Check that there is enough space to allow for there is no person close to the rear of the movement of the tailgate.
Page 77 Access Memorising an opening Motorised opening Motorised closing position Unlocking and opening the There are two possibilities: tailgate with the electronic key / Press and release the exterior Where height is restricted (garage with a low remote control control A. ceiling, ...) it is possible to limit and memorise the opening angle of the tailgate.
Page 78: Precautions In Use
Access Tailgate release The motorised tailgate can be opened and System allowing the mechanical unlocking of Precautions in use closed manually, even if motorisation is the boot in the event of a battery or central In the event of an accumulation of snow activated.
Page 79 Access Alarm System which protects and provides a deterrent against theft and break-ins. It provides the following types of monitoring: Locking the vehicle with full Self-protection function alarm system The system checks for the disconnection of any of its components. Activation The alarm is triggered if the battery, Switch off the ignition and get out of the vehicle.
Page 80 Access Locking the vehicle with exterior perimeter monitoring only Deactivation Deactivate the interior volumetric monitoring Press one of the unlocking buttons on the to avoid unwanted triggering of the alarm in In the case of automatic locking of the remote control: certain cases such as: vehicle (which occurs after a period of short press...
Page 81: Triggering Of The Alarm
Access Triggering of the alarm Locking the vehicle without activating the alarm This is indicated by sounding of the siren and flashing of the direction indicators for Lock or deadlock the vehicle using the key thirty seconds. (integral with the remote control) in the Reactivation of the interior The monitoring functions remain active until driver's door lock.
Page 82: Electric Windows
Access Electric windows Safety anti-pinch To open or close the window, press or pull the When the window rises and meets an obstacle, switch gently. The window stops as soon as the it stops and immediately partially lowers again. switch is released. In the event of unwanted opening of the window on closing, press the switch until the window opens completely, then pull the switch...
Page 83 Access Reinitialisation of the electric windows Deactivating the rear controls for Following reconnection of the battery, the In the event of contact during operation the rear windows safety anti-pinch function must be reinitialised. of the windows, you must reverse the The safety anti-pinch function is not active movement of the window.
Page 84: Front Seats
Comfort Front seats Seat consisting of a seat cushion, a seat back and a head restraint which can all be adjusted to adapt your position for ease of driving and comfort. As a safety measure, seat adjustments should only be done when stationary. Manual adjustments Forwards-backwards Driver's seat backrest angle...
Page 85 Comfort Passenger's seat backrest angle Table position for the passenger's seat backrest Pull the control upwards to adjust the This position, associated with the position of backrest. Check that there is no object that could the rear seats, allows you to carry long objects When the backrest angle is correct, release the interfere with the movement of the seat, inside the vehicle.
Page 86: Electric Adjustments
Comfort Front seats Electric adjustments Forwards-backwards (driver's Seat backrest angle Seat cushion height and angle seat) Tilt the control forwards or rearwards to Operate the rear part of the control Push the control forwards or rearwards to adjust the angle of the seat backrest. upwards or downwards to obtain the slide the seat.
Page 87: Storing Driving Positions
Comfort Storing driving positions Storing a position Recalling a stored position Using buttons M / 1 / 2 Ignition on or engine running Switch on the ignition. Press button 1 or 2 to recall the Adjust your seat and the door mirrors. corresponding position.
Page 88: Additional Adjustments
Comfort Additional adjustments Head restraint height and angle Removing a head restraint Comfort head restraints (depending on version) Depending on version, you can fold the sides to To raise a head restraint, pull it upwards. To remove the head restraint, press the obtain a more comfortable position.
Page 89: Massage Function
Comfort Electric lumbar adjustment Massage function Activation Deactivation Press the control to obtain the desired lumbar support. You can deactivate the massage Press this switch. function at any time by pressing this switch, its indicator lamp goes off. Its indicator lamp comes on and the massage This function provides the front occupants function is activated for a period of 1 hour.
Page 90: Electric Leg Rest
Comfort Electric leg rest Heated seats control Manual passenger seat Electric passenger seat Use the adjustment wheel to switch on and select the level of heating required: Press the front or rear part of the control to Push the control forwards or backwards to 0: Off.
Page 91: Front Armrest
Comfort Front armrest Comfort system for the driver and front passenger. Height adjustment Fully lower the armrest. Raise it to the required position (low, intermediate or high). Once in the high position, lift to release it and return it to the low position.
Page 92: Second Row Seats
Comfort Second-row seats The 3 seats in the 2 row are independent of each other and are all the same width. Their backrests can be folded to vary the load space in the boot. Forwards-backwards adjustment Raise the lever A , located at the front of the seat cushion, and adjust the seat to the desired position.
Page 93: "Comfort" Position
Comfort "Comfort" position Rear head restraints Comfort head restraints Pull the strap B and guide the seat The rear head restraints can be removed and rearwards. have two positions: Depending on version, the sides can be folded The backrest reclines and the seat base pivots high, position for use, to obtain a more comfortable position.
Page 94 Comfort Flat floor Each seat can be folded onto the floor to vary the the space available in the boot. Folding a seat Place the seats in the fully back position. From the outside From the boot, when loading for example Pull firmly upwards on strap C, as indicated You can fold the second-row seats from the by the arrow, to unlock the seat;...
Page 95 Comfort Repositioning a seat Continuity panels If necessary, straighten the continuity Each seat has a continuity panel at the bottom Releasing / locking the continuity panels panels for the seats in the 2 row and lock of the backrest, that once unfolded: Before unfolding the continuity panels, them in place.
Page 96 Comfort Access to the third row Leaving the vehicle from Repositioning a seat, from seats the third-row seats the outside, with the door open Access to the third-row seats is via the outer second-row seats. If there are passengers seated in the third row: manually return the assembly as far as possible rearwards;...
Page 97: Third Row Seats
Comfort Third row seats Repositioning the Concertina boards seats Two rigid concertina boards, which cannot be separated from the vehicle, cover the 2 third-row seats, when these are in the folded position. Folding the concertina boards Remove the luggage net (see the "Boot fittings"...
Page 98: Folding The Seats
Comfort Folding the seats Return the second-row continuity panels to Next push the backrest gently forwards. Before moving the third-row seats, their initial position and lock them. The backrest pivots, folding onto the seat return the rigid floor plates of the Lower the head restraints.
Page 99 Comfort Seat modularity and conﬁ gurations Examples of configurations 5 seats 3 seats 4 seats Maximum loadspace...
Page 100 Comfort Examples of seat configurations 7 seats Maximum loadspace 4 seats For easy modification of your interior vehicle space, all the rear seats can be individually folded: onto the second-row floor, and under the third- row floor. You can then have a load floor that is continuous up to the front seat backrests.
Page 101: Door Mirrors
Comfort Mirrors Door mirrors Folding From outside: lock the vehicle using the electronic key or the Keyless Entry and Starting system. From inside: with the ignition on, pull the control A in the central position rearwards. If the mirrors are folded using control A, they will not unfold when the vehicle is unlocked.
Page 102: Rear View Mirror
Comfort Rear view mirror Automatic tilting in reverse gear Adjustable mirror providing a central rearward view. Equipped with an anti-dazzle system, which darkens the mirror glass and reduces the nuisance to the driver caused by the sun, headlamps from other vehicles... System which provides a view of the ground during parking manoeuvres in reverse gear.
Page 103: Child Surveillance Mirror
Comfort Steering wheel adjustment Child surveillance mirror When stationary, pull the control lever to release the adjustment mechanism. Adjust the height and reach to suit your A child surveillance mirror is fitted above the driving position. rear view mirror. This allows you to monitor the Push the control lever to lock the vehicle’s rear passengers, or it can facilitate adjustment mechanism.
Page 104: Control Panel
Comfort Ventilation The air circulating in the passenger compartment is filtered and originates either from the outside via the grille located at the base of the windscreen or from the inside in air recirculation mode. Air treatment The incoming air follows various routes depending on the controls selected by the driver: direct arrival in the passenger compartment...
Page 105: Recommendations For Ventilation And Air Conditioning
Comfort Recommendations for ventilation and air conditioning In order for these systems to be fully effective, follow the operation and maintenance If after an extended stop in sunshine, guidelines below: the interior temperature is very high, first To obtain an even air distribution, take care not to obstruct the exterior air intake grilles ventilate the passenger compartment for located at the base of the windscreen, the nozzles, the vents and the air outlets, as well a few moments.
Page 106: Temperature Adjustment
Comfort Heating The heating system works only when the The symbol for airflow (a fan) fills progressively The air distribution can be varied by using more engine is running. according to the air flow setting made. than one button. Press the button for the " Air conditioning" By reducing the air flow to the minimum, you Each press of a button activates or deactivates menu to display the page for the system...
Page 107 Comfort Dual-zone manual air conditioning with temperature regulation Temperature adjustment Air flow adjustment The air conditioning system operates with the engine running. The temperature at the nozzles and vents The driver and front passenger can each adjust is regulated by the system according to the Press one of these buttons to the temperature.
Page 108 Comfort Air distribution adjustment Air conditioning On / Off Air intake / Air recirculation The intake of exterior air prevents the formation The air conditioning is designed to These buttons are used to arrange of mist on the windscreen and side windows. operate effectively in all seasons, the distribution of air in the passenger The recirculation of interior air isolates the...
Page 109: Dual-Zone Digital Air Conditioning
Comfort Dual-zone digital air conditioning Temperature adjustment This air conditioning system operates with the engine running, but the ventilation and its controls are available with the ignition on. Operation of the air conditioning and regulation of temperature, air flow and air distribution in the The driver and front passenger can each set passenger compartment are automatic.
Page 110 Comfort Automatic comfort programme This setting is associated with AUTO mode Press the "AUTO" button only. However, on deactivation of AUTO mode, to activate or deactivate the the indicator for the last setting remains on. automatic mode of the air Changing the setting does not reactivate AUTO conditioning system.
Page 111 Comfort Resuming manual control Air ﬂ ow adjustment Air distribution adjustment You can manually adjust one or more settings, while retaining automatic control of the other Press one of these buttons to You can modulate the distribution of air in the functions: increase or decrease the speed passenger compartment using these three buttons.
Page 112 Comfort Air conditioning On/Off Air intake/Air recirculation "Mono" function The air conditioning is designed to The intake of exterior air avoids misting of the The comfort setting for the passenger's side operate efficiently in all seasons, with windscreen and side windows. can be indexed to the driver's comfort setting the windows closed.
Page 113 Comfort "Rear" function Settings for passengers in Settings for the 2 row of seats passengers in the row of seats This function gives rear passengers access to the adjustment controls and allows. the distribution of air conditioned air to the vents for the 2 row of seats, the distribution of ambient air to the vents...
Page 114: Front Demist - Defrost
Comfort Front Demist - Defrost Ventilation with ignition on Press this button to demist or defrost the windscreen and side function windows as quickly as possible. With the ignition on, you can use the The indicator lamp in the button ventilation system and have access to the "...
Page 115: Rear Screen Demist - Defrost
Comfort Rear screen demist - defrost Switching off Switch off the heating of the rear screen and door mirrors as soon as you judge The demisting/defrosting switches off automatically it possible, as reducing the consumption to prevent an excessive consumption of current. of electrical current reduces fuel It is possible to stop the demisting/ consumption.
Page 116: Scented Air Freshener
Comfort Scented air freshener The scented air freshener releases a fragrance into the passenger compartment via the central air vents. To remove the air freshener To insert the air freshener The air freshener contains an empty cartridge when your vehicle is delivered. You therefore need to insert a cartridge in order to use the air freshener.
Page 117: Replacing A Cartridge
Comfort Air freshener button Replacing a cartridge For safety, use only cartridges that are provided for this purpose. Retain the containers for storing used cartridges. Do not recharge or dismantle the cartridges. Keep them out of reach of children and animals.
Page 118: Front Fi Ttings
Comfort Front ﬁ ttings Sun visor. 2. Card holder. 3. Glove box. 4. Central storage. It contains the power and audio sockets. 5. Raised console with closed storage, low console or removable console. 6. Cup holder. Door pockets. 8. Storage below the steering wheel. (Handbook pack).
Page 119: Glove Box
Comfort Sliding sun visor Glove box Sliding blinds Sun visor rails Sliding blinds are provided for your protection The blinds are extended on the sun visor rails. Depending on equipment, it may contain a CD against bright sunlight. They can be adjusted Fold the visor downwards, to protect against player.
Page 120 Comfort Removable console The removable console is a portable storage space secured to the lower centre console. It has a sliding lid, an open storage space and two cup holders. Releasing the removable Refitting the removable console console Raise the locking control located at the Carry out these operations in reverse When not fixed to its carrier, the front of the console.
Page 121: Central Storage Compartment
Comfort Central storage compartment 230 V / 50 Hz power socket To open the central storage compartment, pull the grip and lower the cover. A 230 V / 50 Hz socket (maximum power: It is illuminated on opening. Connect only one device at a time to 120 W) is fitted in the central storage box.
Page 122: Accessory Socket
Comfort 12 V accessory socket Auxiliary socket USB ports The auxiliary socket is located in the central Depending on equipment, one or two USB To connect a 12 V accessory (maximum storage box. ports are located in the central storage box. power: 120 Watts), lift the cover and connect a suitable adaptor.
Page 123 Comfort Mats Removable carpet protection. Fitting Removal To avoid any risk of jamming of the pedals: To remove the mat on the driver's side: only use mats which are suited to move the seat as far back as possible, the fixings already present in the unclip the fixings, vehicle;...
Page 124: Storage Boxes
Comfort Storage boxes Storage below the steering wheel Depending on equipment, storage boxes are located under the front seat. Opening This storage compartment below the steering wheel is intended for stowing your vehicle's handbook pack. Raise the grip and lower the storage box cover.
Page 125: Rear Fi Ttings
Comfort Rear ﬁ ttings Aircraft-style rear tables Individual reading lamps Rear table stowed Rear table opened Reading lamps C may be fitted in the front seat backrests, behind the tables. They illuminate These tables, fitted to the backs of the front the surface of the tables without disturbing the seats, incorporate a cup-holder recess A and a other passengers.
Page 126 Comfort Side blinds Storage wells 12 V accessory socket Fitted to the windows for the 2 row seats, they protect There are two storage wells under the rear To connect a 12 V accessory (maximum the passenger compartment from the sun's rays. passengers' feet.
Page 127: Rear Multimedia
Comfort Rear multimedia Description The pack includes: the connection and control panel fitted on the rear face of the centre console, two 7-inch screens built into the front head restraints (with protective covers), two wireless Bluetooth technology headphone sets with rechargeable batteries, a 12 V charger with two outlets allowing the simultaneous charging of two headphones,...
Page 128: Operation
Comfort Operation It is possible at any time to modify the source for the video display (using button 6 or 7 on the control panel: the indicator lamp for the source selected comes on) as well as the audio channel (using the selector on the headphones).
Page 129: Boot Fi Ttings
Comfort Boot ﬁ ttings Rear parcel shelf (see details on a following page) 2. Hooks (see details on a following page) 3. Torch (see details on a following page) 4. Storage boxes (see details on a following page) 5. Storage net 6.
Page 130: Rear Parcel Shelf
Comfort Rear parcel shelf Hooks Storage boxes To remove the shelf: The hooks can be used to secure shopping Remove the boot carpet for access to the unhook the two cords, bags. storage boxes. raise the shelf slightly, then remove it. Depending on the configuration, they are laid out for storing: There are several options for storing the shelf:...
Page 131 Comfort Boot ﬁ ttings Luggage cover blind (see details on a following page) 2. Torch (see details on a following page) 3. Concertina boards 4. Lashing eyes 5. 12 V socket (maximum power: 120 Watts) 6. Arm rest with cup holder and storage space Retaining straps 8.
Page 132: Installation
Comfort Luggage cover roller In the 5-seat configuration, it is installed behind the second-row seats, with the third-row seats folded away. In the 7-seat configuration, it is stowed behind the third row seats. Installation Removal Position the left and right hand ends of the Disengage the roller guides from the rails roller in cut-out A , with the mobile flap at in the pillars B.
Page 133 Comfort Stowing behind the 3 row seats Ensure that the 3 row seats are folded. To fold the 3 row seats with the roller Fold the first two concertina boards. stowed at the rear, it is necessary to raise the Install the roller in the space above the arm concertina boards in order to allow access to rest, one side after the other, inclining it...
Page 134 Comfort Torch This is a removable lamp, fitted in the side of the boot, which can be used to illuminate the Extract the torch from its location by pulling boot or as a torch. it from the front. Press the switch, located on the back, to switch the torch on or off.
Page 135: Starting-Switching Off The Engine With The Electronic Key
Driving Starting-switching off the engine with the electronic key Starting the engine If one of the starting conditions is not met, a reminder message appears in the instrument panel screen. In some circumstances, it is necessary to turn the steering wheel slightly while pressing the "START/STOP"...
Page 136: Emergency Stop
Driving Switching off the engine Emergency stop Immobilise the vehicle. In the event of an emergency only, Place the gear selector lever at N for the engine can be switched off vehicles with an electronic gearbox, P or N without any conditions. To do this, for an automatic gearbox, or neutral with a press the "START/STOP"...
Page 137: Starting-Switching Off The Engine With The "Keyless Entry And Starting" System
Driving Starting-switching off the engine with the "Keyless Entry and Starting" system Starting the engine Briefly press the " START/STOP" If the electronic key is not detected in button. the zone, a message is displayed. Move The steering column locks and the electronic key into the zone so that the engine starts more or less the engine can be started.
Page 138: Emergency Starting
Driving Switching off the engine Emergency starting Immobilise the vehicle. Place the gear selector lever at N for vehicles with an electronic gearbox, P or N with an automatic gearbox, or neutral with a manual gearbox. With the electronic key inside the vehicle, press the "...
Page 139: Emergency Switch-Off
Driving Emergency switch-off Electronic key not recognised In the event of an emergency only, the engine can be switched of without conditions. To do this, press and hold the "START/STOP" button for about 3 seconds. In this case the steering column locks as soon as the vehicle stops.
Page 140: Anti-Theft Protection
Driving Ignition on without Anti-theft protection starting Electronic engine immobiliser The keys contain an electronic chip which has With the electronic key in the reader or the a secret code. When the ignition is switched Keyless Entry and Starting key inside the on, this code must be recognised in order for vehicle, pressing the "START/STOP"...
Page 141: Electric Parking Brake
Driving Electric parking brake Indicator lamp This indicator lamp comes on in the In the event of a battery failure, the instrument panel and in the control electric parking brake no longer works. lever to confirm the application of the As a safety measure, if the parking parking brake.
Page 142: Manual Operation
Driving Manual operation Manual release With the ignition on or the engine running, to release the parking brake: press the brake pedal, while maintaining pressure on the brake pedal, briefly push the control lever. Label on door panel The complete release of the parking brake is confirmed by the brake indicator lamp and the Before leaving the vehicle, check that When towing, parking on a steep...
Page 143: Automatic Operation
Driving Automatic operation Automatic release Automatic application Ensure first that the engine is running and the The complete release of the parking With the vehicle stationary, the parking brake driver's door is properly closed. brake is confirmed by the brake is automatically applied when the engine The electric parking brake releases indicator lamp and the P indicator...
Page 144: Special Cases
Driving Special cases Parking the vehicle with the In some situations, you may need to operate brake released the parking brake manually. The complete release of the parking In very cold conditions, it is brake is confirmed by the brake Immobilisation of the vehicle recommended that the parking brake indicator lamp and the P indicator...
Page 145: Deactivating Automatic Operation
Driving Emergency braking Deactivating automatic operation The emergency braking should only be used in an exceptional situation. In some situations, such as very cold weather From this point the parking brake can only or towing (caravan, recovery), it may be be applied and released manually using the In the event of a failure of the main service necessary to deactivate automatic operation of...
Page 146 Driving The various alert situations are described in the table below. In the event of a fault with the electric parking brake it is recommended that you contact a CITROËN dealer or a qualified workshop without delay. Situations Consequences Display of the message "Parking brake fault" and the Automatic release is not available.
Page 147 Driving Situations Consequences Display of the message "Parking brake fault" and of the The Parking Brake is faulty, the manual and automatic functions may not operate. When stationary, to immobilise your vehicle: following warning lamps: Pull and hold the control lever for about 7 to 15 seconds, until the warning lamp comes on in the instrument panel.
Page 148: Hill Start Assist
Driving Hill start assist Operation System which keeps your vehicle immobilised temporarily (approximately 2 seconds) when starting on a gradient, the time it takes to move your foot from the brake pedal to the accelerator pedal. This system only operates when: the vehicle is completely stationary, with your foot on the brake pedal, certain conditions of slope are met,...
Page 149: Speed Manual Gearbox
Driving 5-speed manual 6-speed manual gearbox gearbox Engaging reverse gear Engaging 5 or 6 gear Engaging reverse gear Raise the ring under the knob and move the gear lever to the left then forwards. Only engage reverse gear when the vehicle is stationary with the engine at idle.
Page 150: Gear Selector Lever
Driving 6-speed electronic gearbox system Gear selector lever Steering mounted control paddles Six-speed electronic gearbox system which offers a choice between the comfort of fully automatic operation and manual gear changing. There are two driving modes: automated mode for automatic control of the gears by the gearbox, without any action on the part of the driver manual mode for sequential gear changing...
Page 151: Moving Off
Driving Displays in the instrument panel Moving off Select position N. Select automated mode (position A) or Press the brake pedal down fully. manual mode (position M) or reverse Start the engine. (position R ). Release the parking brake by pulling the N appears in the instrument panel control lever, if automatic operation has screen.
Page 152: Automated Mode
Driving Automated mode Manual mode Select position A. Select position M. The gears engaged are displayed in succession AUTO or A and the gear engaged is in the instrument panel. displayed in the instrument panel. The gear change requests are only acted on if the engine speed permits.
Page 153: Stopping The Vehicle
Driving Reverse Stopping the vehicle Operating fault To engage reverse gear R, the vehicle must be Before switching off the engine, you can: With the ignition on, the flashing of A or immobilised with your foot on the brake pedal. move to position N to engage neutral, AUTO, accompanied by an audible signal and Select position R.
Page 154: Automatic Gearbox
Driving Automatic gearbox Gear selector lever This gearbox offers two driving modes. automated mode for automatic To come out of position P , move the management of the gears by the gearbox, without any action on the part of the driver, gear selector to the right to the desired manual mode for sequential gear changing position, while keeping your foot on the...
Page 155 Driving Steering mounted control paddles Displays in the instrument panel Moving off With your foot on the brake pedal, select position P or N. Start the engine. Otherwise, there is an audible signal accompanied by a message. If P is displayed in the instrument panel, although the gear selector is in another position, place the gear selector in position P to be able to start the engine.
Page 156 Driving Check that the symbol displayed in the When the engine is running at idle, Never select position N when driving. instrument panel agrees with the position brakes releases, if position R, D or M is If position N is engaged in error when engaged.
Page 157 Driving Automated mode Manual mode Temporary manual control of the Select position D. Select position M. gears Use the " + " and "- " steering mounted control paddles to change gear. The gears engaged are displayed successively D and the gear engaged are displayed in the in the instrument panel.
Page 158: Parking The Vehicle
Driving Parking the vehicle Operating fault Before switching off the engine, you can change to position P or N to be in neutral. In the event of a fault with the In either case, apply the parking brake to gearbox, the service warning lamp immobilise the vehicle, unless it is programmed comes on in the instrument panel, in automatic mode.
Page 159: Gear Shift Indicator
Driving Gear shift indicator System which reduces fuel consumption by advising the driver to change up. With an electronic gearbox, the system is only active in Manual mode. Operation Depending on the driving situation and your Example: The system adapts its gear change vehicle's equipment, the system may advise You are in third gear.
Page 160: Stop & Start
Driving Stop & Start The Stop & Start system puts the engine temporarily into standby - STOP mode - during stops in the traffic (red lights, traffic jams, or other...). The engine restarts automatically - START mode - as soon as you want to move off. The restart takes place instantly, quickly and silently. Perfect for urban use, the Stop &...
Page 161 Driving Deactivation Going into engine START mode Special cases: START invoked Deactivation of Stop & Start is done in the automatically "Driving assistance" menu. The "ECO" warning lamp goes off START mode is invoked automatically when: Press this button to deactivate the and the engine starts automatically: you open the the driver's door, system.
Page 162: Maintenance
Driving Reactivation Operating fault Maintenance Press this button again. In the event of a fault with the system, this warning lamp comes on continuously. The system is active again; this is Have it checked by a CITROËN dealer or a confirmed by the indicator lamp in the qualified workshop.
Page 163: Display Of Inter-Vehicle Time
Driving Display of inter-vehicle time Activation / deactivation Using a radar located at the front of the vehicle, The system is active in a speed range this system helps the driver maintain a safe between 42 and 93 mph (70 and Activation of the system is done in the "...
Page 164 Driving Displays Once the system has been activated and the speed conditions are met, a symbol is displayed in the instrument panel. Symbol Associated message Comments No vehicle detected by the radar. A vehicle is detected but the inter-vehicle time is more than 3 seconds. No value is displayed.
Page 165 Driving Symbol Associated message Comments " SYSTEM INACTIVE: Speed If the speed of your vehicle is outside the operating range. unsuitable" Where the speed is not suitable, a message is displayed while the speed is outside limits (below 42 mph (70 km/h) or above 93 mph (150 km/h), approximately). However, when decelerating, the system is deactivated below 27 mph (45 km/h).
Page 166: Operating Limits
Driving Operating limits Operating fault The vehicle being followed may not be detected In the event of a fault with the system, The operation of the radar, located in in certain conditions such as, for example: this warning lamp is displayed the front bumper, may be disturbed by when turning, accompanied by a message.
Page 167: Memorising Speeds
Driving Memorising speeds This function allows speeds to be saved, which can then be offered to set the two systems: the speed limiter (to limit the speed of the vehicle) or the cruise control (for a vehicle cruising speed). You can memorise up to six speed settings for each of the two systems. By default, some speeds are already memorised. Memorisation Go to the "Driving assistance"...
Page 168: Speed Limiter
Driving Speed limiter Once the programmed speed limit is reached, additional pressure on the accelerator pedal has no effect. Steering mounted controls Displays in the instrument panel System which prevents the vehicle from exceeding the speed programmed by the driver. The speed limiter is switched on manually: it requires a programmed speed of at least 20 mph (30 km/h).
Page 169 Driving Adjusting the speed limit setting Turn wheel 1 to the "LIMIT" position: the You do not have to switch the speed limiter on a press on button 5 : in order to set the speed. the six speeds memorised, displayed in speed limiter mode is selected but is not Once the function is selected, you can modify the touch screen tablet,...
Page 170: Switching Off
Driving Temporarily exceeding Operating fault the programmed speed Press firmly on the accelerator pedal, Flashing of the dashes indicates a fault with the On sharp acceleration, as when going beyond the point of resistance, to speed limiter. descending a steep hill, the speed exceed the programmed speed limit.
Page 171: Cruise Control
Driving Cruise control System which automatically maintains the speed of the vehicle at the value programmed by the driver, without any action on the accelerator pedal. Steering mounted controls Displays in the instrument panel The cruise control is switched on manually: it requires a minimum vehicle speed of 25 mph (40 km/h) and engagement of: at least fourth gear on a manual gearbox,...
Page 172 Driving Modiﬁ cation of the initial speed Turn wheel 1 to the "CRUISE" position: the setting cruise control mode is selected but is not switched on (Pause). If the cruise control is on, you can then modify pressing button 5: Press button 2 or 3 : your vehicle's current the initial speed in one of the following ways: the six memorised speeds are displayed...
Page 173 Driving Operating fault Exceeding the programmed Flashing of the dashes indicates a fault with the When the cruise control is switched on, speed cruise control. be careful if you maintain the pressure Have it checked by a CITROËN dealer or a on one of the programmed speed If the programmed speed is exceeded, the qualified workshop.
Page 174: Active Cruise Control
Driving Active cruise control Principles of operation This systems allows, in addition to maintaining your vehicle's speed at a value that you have defined, the inter-vehicle time you have Using a radar with a range of about 100 metres, selected between your vehicle the the one The active cruise control operates by located at the front of the vehicle, this system ahead to be maintained (2 seconds by default,...
Page 175: General Points
Driving General points The active cruise control is switched on The active cruise control can above be paused The active cruise control cannot in any manually: it requires that the speed of the vehicle manually with the control, or automatically: circumstances replace the observation be between 25 mph (40 km/h) and 90 mph by pressing the brake or clutch pedal,...
Page 176: Operation
Driving Steering mounted controls Operation Switching on Turn the wheel 1 to the "CRUISE" position: cruise control mode is selected, but not started (Pause). Press one of the buttons 2 or 3: the current speed of your vehicle becomes the cruise speed setting (set on the fly).
Page 177 Driving Displays in the instrument panel Exceeding the programmed In the event of the presence of a speed vehicle detected by the radar, if the speed selected is much higher than It is possible to exceed the programmed speed the speed of that vehicle, the system temporarily by depressing the accelerator is not activated and the alert message pedal.
Page 178 Driving Driving situations and associated alerts The table below describes the alerts and the messages displayed for the different driving situations. The display of these alerts is not sequential. Display in the Symbol Associated message Comments instrument panel No vehicle detected: the system operates as a conventional cruise control.
Page 179 Driving Display in the Symbol Associated message Comments instrument panel "SPEED ADJUSTED" Detection of a vehicle that is too close or running at a speed lower than your vehicle's cruise speed setting. The system uses engine braking to slow your vehicle and then hold it at the speed of the vehicle in front so as to maintain the programmed inter-vehicle time.
Page 180: Limits Of Operation
Driving Limits of operation The active cruise control uses only engine As the radar's field of view is quite narrow, it is braking to slow the vehicle. Consequently the possible that the system may not detect: vehicle looses speed slowly, as when releasing the accelerator pedal.
Page 181 Driving Operating fault In the event of a fault with the active cruise When the cruise control is working, take The operation of the radar, located in control, you are alerted by an audible signal care if making a maintained press on the front bumper, may be disturbed by and display of the message message "Driving one of the cruise control programmed...
Page 182: Collision Risk Alert
Driving Collision risk alert System providing a warning to the driver that their vehicle is at risk of collision with the vehicle in front. Setting the thresholds for The collision risk alert system can be activated or deactivated by the driver. the alert From the secondary page of the "...
Page 183 Driving Alerts According to the collision risk detected by the Level 3: an increase in The change from one level of alert system and the alert threshold chosen, three the tension of the driver's to the next takes place if the driving levels of alert can be triggered: seat belt, to hold the driver conditions do not change (speed...
Page 184 Driving Operating fault In the event of a fault, you are The operation of the radar, located in alerted by the display of the Service the front bumper, may be disturbed by warning lamp, accompanied by a accumulations of grime (dust, mud...) message.
Page 185: Lane Departure Warning System
Driving Lane departure warning system Activation / deactivation Operating fault Activation and deactivation of the function is In the event of a fault, this warning done in the " Driving assistance " menu of the lamp comes on accompanied by an touch screen tablet.
Page 186: Blind Spot Sensors
Driving Blind spot sensors Activation of the system is done in the " Driving assistance " menu, with the ignition on. Press this button to activate the function; the associated indicator lamp comes on. This indicator lamp comes on in the instrument panel.
Page 187 Driving comes on in the door mirror on the side in question as soon as a vehicle - car, lorry, bicycle - is detected and the following conditions are fulfilled: all the vehicles must be moving in the same direction, the speed of your vehicle is between 7 and 87 mph (12 and 140 km/h), the difference in speed between your...
Page 188 Driving Operating fault The system may suffer temporary interference in certain weather conditions (rain, hail...). To deactivate the system, press In the event of a fault, the warning In particular, driving on a wet surface lamp flashes then goes off. this button again;...
Page 189: Rear Parking Sensors
Driving Parking sensors Rear parking sensors The system is switched on by engaging reverse gear. This is accompanied by an audible signal. The system is switched off when you exit reverse gear. This system indicates the proximity of an obstacle (person, vehicle, tree, gate, etc.) which Visual assistance comes within the field of detection of sensors located in the bumper.
Page 190: Front Parking Sensors
Driving Front parking sensors Operating fault Deactivation / Activation of the In addition to the rear parking sensors, the front In the event of a malfunction of front and rear parking sensors parking sensors are triggered when an obstacle the system, when reverse gear is detected in front and the speed of the vehicle is engaged this warning lamp is The system is deactivated in the "...
Page 191: Reversing Camera
Driving Reversing camera The reversing camera is activated automatically The space between the blue lines represents The blue lines represent the general direction when reverse gear is engaged. the width of your vehicle except for the door of the vehicle. Depending on version, the image is displayed in mirrors.
Page 192: Rear Vision
Driving 360 Vision Rear vision This system is a visual aid which in no circumstances can replace the vigilance The camera located in the tailgate is activated and responsibility of the driver. and the view of the area behind your vehicle is The images provided by the cameras displayed in the instrument panel and behaves may be deformed by the relief.
Page 193: Operation
Driving Operation 360 vision "Rear camera". The cameras located in the front and rear bumpers and under the door mirrors are The view selected is displayed in the instrument panel. activated and a reconstruction of the view from above your vehicle in its immediate surroundings The display in the instrument panel is displayed in the instrument panel.
Page 194: Park Assist
Driving Park Assist This system provides active assistance with The Park Assist system provides assistance for During a manoeuvre the steering wheel parking, detecting a parking space then the following manoeuvres: turns quickly: do not hold the steering controlling the steering to park in the space. wheel, do not place your hand between It controls the steering while the driver the spokes of the steering wheel and...
Page 195 Driving The sequence of manoeuvres and the You should always check the The park sensors function is not driving instructions are displayed in the surroundings of your vehicle before available during parking space instrument panel. starting a manoeuvre. measurement. It intervenes later when manoeuvring to warn you that your The assistance is vehicle is approaching an obstacle: the...
Page 196 Driving Operation Operate the direction indicator on the Assistance with parallel parking parking side chosen to activate the manoeuvres measurement function. You should drive When you have identified a parking space, Limit the speed of the vehicle to at a distance of between 0.5 m and 1.5 m a maximum of 12 mph (20 km/h) from the row of parked vehicles.
Page 197 Driving Move forwards slowly until a message is The assisted parking manoeuvre is in At the end of the manoeuvre, the operating displayed, accompanied by an audible progress. indicator lamp goes out in the instrument signal, asking you to engage reverse gear. Without exceeding 5 mph (8 km/h), move panel, accompanied by a message and an forwards and backwards, aided by the...
Page 198 Driving Assistance in exiting from a The manoeuvre is complete when the vehicle's Operate the direction indicator for the exit parallel parking space front wheels are clear of the parking space. side chosen. When you want to leave a parallel parking At the end of the manoeuvre, the indicator lamp Engage reverse or forward gear and space, start the engine.
Page 199 Driving When several successive bays are found, the vehicle will be directed towards the last one. Assistance with bay parking Operate the direction indicator on the manoeuvres parking side chosen to activate the Once you have identified a measurement function. You should drive parking zone, press this control at a distance of between 0.5 m and 1.5 m at the steering wheel,...
Page 200 Driving During a bay parking manoeuvre, the Park Assist system is automatically deactivated once the rear of the vehicle is within 50 cm of an obstacle. During parking and exit from At the end of the manoeuvre, the operating Select reverse, release the steering wheel parking manoeuvres, the reversing indicator lamp goes out in the instrument panel, and start moving without exceeding 5 mph...
Page 201: Operating Faults
Driving Deactivation Switching off The system is deactivated automatically: The system is switched off automatically: In the event of a fault with the on switching off the ignition, when towing a trailer, power steering, this warning lamp if the engine stalls, if the driver's door is opened, comes on in the instrument panel if no manoeuvre is started within 5 minutes...
Page 202: Exterior Lighting Controls
Visibility Exterior lighting controls System for selection and control of the various front and rear lamps providing the vehicle's lighting. Main lighting Additional lighting Programming The various front and rear lamps of the vehicle Other lamps are provided to meet the The setting of some functions can be adjusted: are designed to adapt the driver's visibility requirements of particular driving conditions:...
Page 203 Visibility Main lighting Displays Selection of main lighting mode Illumination of the corresponding indicator lamp in the instrument panel confirms that the lighting selected is on. Turn the ring A to place the desired symbol against the mark. Lighting off / daytime running lamps. Automatic illumination of headlamps.
Page 204: Fog Lamps
Visibility Foglamps The foglamps operate with the dipped and main When the headlamps switch off with automatic beam headlamps. illumination of headlamps or when the dipped beam headlamps are switched off manually, the Rear foglamps foglamps and sidelamps remain on. Turn the ring rearwards to switch off the foglamps, the sidelamps will then switch To switch on the foglamps, turn the ring C...
Page 205 Visibility Switching off the lighting Operation of the rear foglamps is In good or rainy weather, by both day when switching off the ignition inhibited with the tailgate open. and night, the front foglamps and the Opening the boot when these lamps are rear foglamps are prohibited.
Page 206: Manual Guide-Me-Home Lighting
Visibility Manual guide-me-home lighting Side markers for the vehicle by illumination of The temporary illumination of the dipped beam the sidelamps on the traffic side only. headlamps after the vehicle's ignition has been Within one minute of switching off the switched off makes the driver's exit easier when ignition, operate the lighting control stalk up the light is poor.
Page 207: Automatic Illumination Of Headlamps
Visibility Automatic illumination Automatic "guide-me- of headlamps home" lighting Deactivation When the automatic illumination of headlamps Turn the ring to another position. function is activated, under low ambient Deactivation of the function is light the dipped beams headlamps come on accompanied by the display of a message.
Page 208: Automatic Headlamp Dipping
Visibility Automatic headlamp dipping System which automatically changes between dipped and main beam according to the ambient light level and the driving conditions, using a camera located in the rear view mirror. This automatic headlamp dipping system is a driving aid. The driver remains responsible for the vehicle's lighting, its correct use for the prevailing conditions of light, visibility and traffic...
Page 209 Visibility Switching on Pause Put the lighting control stalk ring If the situation requires a change of headlamp in the "AUTO" position. beam, driver can take over at any time. The system may suffer interference or not work correctly: Flashing the headlamps In the "...
Page 210: Exterior Welcome Lighting
Visibility Daytime running lamps Door mirror spotlamps Exterior welcome lighting (LEDs) The remote switching on of the lighting makes your approach to the vehicle easier in poor light. It is activated when the lighting control is in the "AUTO" position and the level of light detected by the sunshine sensor is low.
Page 211: Manual Adjustment
Visibility Manual adjustment of headlamps To avoid causing a nuisance to other road users, the headlamps should be adjusted according to the load in the vehicle. 0. 1 or 2 people in the front seats. Intermediate setting. 5 people + maximum authorised load. Intermediate setting.
Page 212: Cornering Lighting
Visibility Cornering lighting Switching on This system starts: when the corresponding direction indicator is switched on, from a certain angle of rotation of the steering wheel. Switching off With dipped or main beams, this system with cornering lighting makes use of the beam from a front foglamp to The system does not operate: illuminate the inside of a bend, when the vehicle below a certain angle of rotation of the...
Page 213: Directional Lighting
Visibility Directional lighting Operating fault on, this system allows the light beams to better If a fault occurs, this warning lamp flashes follow the road. in the instrument panel, accompanied by The use of this system, coupled with the a message in the screen. xenon headlamps and the cornering lighting, considerably improves the quality of your Contact a CITROËN dealer or a qualified...
Page 214: Wiper Controls
Visibility Wiper controls Programming Manual controls Windscreen wipers Your vehicle may also include some functions The wipers are controlled directly by the driver. that can be configured: The front wiper system includes a automatic rain sensitive windscreen wipers, safety device which can temporarily rear wiping on engaging reverse gear.
Page 215: Rear Wiper
Visibility Rear wiper Rear wiper selection ring: park, intermittent wipe, wash-wipe (set duration). Reverse gear If a significant accumulation of snow or ice is present, deactivate the automatic When reverse gear is engaged, the rear wiper rear wiper via the " Driving assistance" will come into operation if the windscreen menu, then "Vehicle settings".
Page 216: Headlamp Wash
Visibility Windscreen wash and headlamp wash Screenwash and washer jets Headlamp wash Adjusting the jets The headlamps operate when the vehicle is Pull the windscreen wiper stalk towards The front washers include an adjustment for the moving and when the dipped beam headlamps you.
Page 217: Automatic Rain Sensitive Windscreen Wipers
Visibility Automatic rain sensitive windscreen wipers The windscreen wipers operate automatically, without any action on the part of the driver, if rain is detected (sensor behind the rear view mirror), adapting their speed to the intensity of the rainfall. Switching on Switching off The automatic rain sensitive windscreen wipers must be reactivated by pushing...
Page 218 Visibility Special position of the windscreen wipers Operating fault If a fault occurs with the automatic rain sensitive wipers, the wipers will operate in intermittent mode. Have it checked by CITROËN dealer or a qualified workshop. This position permits release of the windscreen To maintain the effectiveness of the wiper blades.
Page 219: Courtesy Lamps
Visibility Courtesy lamps Front - rear courtesy lamps Front - rear map reading lamps In this position, the courtesy lamp comes on gradually: With the ignition on, press the corresponding switch. when the vehicle is unlocked, when the electronic key is removed from Take care to avoid leaving anything the reader, in contact with the courtesy lamps.
Page 220: Panoramic Sunroof
Visibility Panoramic sunroof It is fitted with an electrically controlled blind. Opening the roof blind Closing the roof blind Anti-pinch Rotate the control A to position 0 to close the roof blind. The blind has an anti-pinch function. Rotate the control A to slide the roof blind At the end of its travel, when the blind to the desired position (positions 1 to 4 ).
Page 221: Interior Mood Lighting
Visibility Interior mood lighting Footwell lighting The dimmed passenger compartment lighting improves visibility in the vehicle when the light is poor. Switching on The interior mood lighting can be activated or deactivated via the "Driving assistance " menu, then " Vehicle settings ". The soft lighting provided by the footwell lamps improves visibility in the vehicle when the light At night, the lighting of the dashboard,...
Page 222: Direction Indicators
Safety Direction indicators Hazard warning lamps Horn Left: lower the lighting stalk passing the A visual warning by means of the direction Audible warning system to alert other road point of resistance. indicators to alert other road users to a vehicle users to an imminent danger.
Page 223: Emergency Or Assistance Call
Safety Emergency or Warning triangle assistance call This safety device should be used in addition to the hazard warning lamps. Its presence in the vehicle is mandatory. Before leaving your vehicle to set up and install the triangle, switch on the hazard warning lamps and put on your high visibility vest.
Page 224: Tyre Under-Infl Ation Detection
Safety Tyre under-inﬂ ation detection System which automatically checks the pressure of the tyres while driving. The system continuously monitors the The under-inflation detection system The inflation pressures defined for pressures on the four tyres, once the vehicle is does not replace the vigilance or the your vehicle can be found on the tyre moving.
Page 225 Safety Under-inflation alert Reinitialisation This is given by fixed illumination of A label reminds you of the need to reinitialise In the event of a puncture, use the this warning lamp, accompanied by the system every time one or more tyre temporary puncture repair kit or the spare an audible signal and, depending on pressure is adjusted, and after changing one or...
Page 226 Safety Operating fault Reinitialisation of the system is done with the Before reinitialising the system, ensure ignition on and the vehicle stationary. that the pressures of the four tyres are From the secondary page of the " Driving correct for the use of the vehicle and in assistance"...
Page 227: Electronic Stability Programme (Esc)
Safety Electronic stability programme (ESC) Definitions Electronic Stability Programme (ESC: Electronic Stability Control) incorporating the Anti-lock braking system (ABS) Anti-slip regulation (ASR) following systems: and electronic brake force the anti-lock braking system (ABS) and the The ASR system (also known as Traction distribution (EBFD) electronic brake force distribution (EBFD), Control) optimises traction in order to avoid...
Page 228 Safety Intelligent traction control Operation system ("Snow motion") Anti-lock braking system (ABS) Your vehicle has a system to help driving on When changing wheels (tyres and rims), and electronic brake force snow: intelligent traction control. make sure that these are approved for distribution (EBFD) This system detects situations of difficult your vehicle.
Page 229 Safety Deactivation Operating fault If this warning lamp comes on, In exceptional conditions (starting a vehicle accompanied by an audible signal which is bogged down, stuck in snow, on soft and a message, this indicates a fault ground...), it may be advisable to deactivate with the system.
Page 230: Front Seat Belts
Safety Seat belts Front seat belts Seat belt reels with reversible pretension This system provides automatic adjustment of the tension of the driver's and passenger's seat belts after fastening, once the vehicle's speed is above 6 mph (10 km/h). In addition, as soon as the system detects a potentially dangerous driving situation, this system reacts by drawing in slack in the belt, (for example, under heavy or sharp braking or...
Page 231 Safety row seat belts row outer seat belts (stowing) Fastening The rear seats are each fitted with a seat belt, Guide the belt as it reels in and place the three-point anchorages with inertia reel and tongue on the magnet at the side anchorage Pull the strap, then insert the tongue in the force limiter (except for the centre rear seat).
Page 232 Safety row centre seat belt 3rd row seat belts The seat belt for the centre rear seat is built into the roof. Fastening Unfastening Fastening Pull the strap and insert the tongue A into Press the red button in buckle B , then Detach the seat belt strap from its retaining the right hand buckle.
Page 233 Safety Seat belt not fastened and unfastened alerts Seat belts unfastened alert The instrument panel includes a seat belt not- At speeds above 12 mph (20 km/h), these fastened warning lamp A as well as an indicator alerts flash, accompanied by an audible signal of the location of the non-fastened belts B .
Page 234 Safety The driver must ensure that passengers use In order to be effective, a seat belt must: Recommendations for children the seat belts correctly and that they are all be tightened as close to the body as Use a suitable child seat if the passenger is restrained securely before setting off.
Page 235 Safety Airbags System designed to maximise the safety of the occupants (with the exception of the rear centre passenger) in the event of violent collisions. The airbags supplement the action of the force- limiting seat belts (with the exception of the centre rear passenger).
Page 236: Front Airbags
Safety Front airbags To assure the safety of your child, the passenger's front airbag must be deactivated when you install a "rear facing" child seat on the front passenger seat. Otherwise, the child would risk being seriously injured or killed if the airbag were deployed.
Page 237 Safety Operating fault If this warning lamp flashes, contact If this warning lamp comes on in the instrument panel, accompanied by a CITROËN dealer or a qualified an audible warning and a message, workshop. The passenger's front contact a CITROËN dealer or a airbag may no longer be deployed in qualified workshop to have the the event of a serious impact.
Page 238: Lateral Airbags
Safety Lateral airbags Impact detection zones System which protects the driver and front passenger in the event of a serious side impact A. Front impact zone. in order to limit the risk of injury to the chest, B. Side impact zone. between the hip and the shoulder.
Page 239: Curtain Airbags
Safety Curtain airbags Deployment Operating fault System which protects the driver and passengers (with the exception of the rear The curtain airbag is deployed at the same If this warning lamp comes on in the centre passenger) in the event of a serious side time as the corresponding lateral airbag in the instrument panel, accompanied by an impact in order to limit the risk of injury to the...
Page 240 Safety For the airbags to be fully effective, observe the following safety rules: Front airbags Lateral airbags Sit in a normal upright position. Wear a correctly adjusted seat belt. Do not drive holding the steering wheel by its Use only approved covers on the seats, Do not leave anything between the spokes or resting your hands on the centre compatible with the deployment the lateral...
Page 241 Safety General points relating to child seats Although one of CITROËN main criteria when designing your vehicle, the safety of your children also depends on you. For maximum safety, please observe the CITROËN recommends that children following recommendations: should travel in the rear seats of your in accordance with European regulations, vehicle.
Page 242 Safety Child seat in the front "Rearward facing" "Forward facing" Passenger seat in the midway longitudinal position, the lowest height position, then When a "rearward-facing" child seat is When a "rearward-facing" child seat is the height control lever pulled 11 times. installed on the front passenger seat, adjust installed on the front passenger seat, adjust the vehicle seat to the midway longitudinal...
Page 243: Deactivating The Passenger's Airbag
Safety Deactivating the passenger's airbag The warning label present on both sides of Never install a rearward-facing child the passenger's sun visor repeats this advice. restraint system on a seat protected by In line with current legislation, the following an active front airbag. This could cause two pages contain this warning in all of the the death of the child or serious injury.
Page 244 Safety BG НИКОГА НЕ инсталирайте детско столче на седалка с АКТИВИРАНА предна ВЪЗДУШНА ВЪЗГЛАВНИЦА. Това можеда причини СМЪРТ или СЕРИОЗНО НАРАНЯВАНЕ на детето. CS NIKDY neumisťujte dětské zádržné zařízení orientované směrem dozadu na sedadlo chráněné AKTIVOVANÝM čelním AIRBAGEM. Hrozí nebezpečí SMRTI DÍTĚTE nebo VÁŽNÉHO ZRANĚNÍ.
Page 245 Safety MT Qatt m’ghandek thalli tifel/tifla marbut f’siggu dahru lejn l-Airbag attiva, ghaliex tista’ tikkawza korriment serju jew anke mewt lit-tifel/tifla Plaats NOOIT een kinderzitje met de rug in de rijrichting op een zitplaats waarvan de AIRBAG is INGESCHAKELD. Bij het afgaan van de airbag kan het KIND ERNSTIG OF DODELIJK GEWOND raken.
Page 246 Safety Child seat at the rear "Rearward facing" "Forward facing" Seats in the 3 When a "rearward facing" child seat is installed When a "forward facing" child seat is installed When a child seat is installed on a 3 on a rear passenger seat, move the vehicle's on a rear passenger seat , move the vehicle's passenger seat , move the 2 row seat...
Page 247 Safety Installation of child seats secured using the seat belt In accordance with European regulations, this table indicates the options for installing child seats secured using the seat belt and universally approved (a) in relation to the weight of the child and the seat in the vehicle. Weight of the child / indicative age Seat Groups 0 (b) and 0+...
Page 248 Safety (a) Universal child seat: child seat which can be U : seat suitable for the installation of a child Remove and stow the head restraint installed in all vehicles using the seat belt. seat secured using the seat belt and before installing a child seat on a (b) Group 0: from birth to 10 kg.
Page 249 Safety Installation of child seats secured using the seat belt In accordance with European regulations, this table indicates the options for installing child seats secured using the seat belt and universally approved (a) in relation to the weight of the child and the seat in the vehicle. Weight of the child / indicative age Seat Groups 0 (b) and 0+...
Page 250 Safety (a) Universal child seat: child seat which can be U : seat suitable for the installation of a child Remove and stow the head restraint installed in all vehicles using the seat belt. seat secured using the seat belt and before installing a child seat on a (b) Group 0: from birth to 10 kg.
Page 251: "Isofix" Mountings
Safety "ISOFIX" mountings latest ISOFIX regulations . The seats, represented below, are fitted with regulation ISOFIX mountings: To secure the child seat to the TOP TETHER : remove and stow the head restraint before installing the child seat on this seat (refit it after the child seat has been removed), remove the TOP TETHER cover by pulling at its cut-out,...
Page 252 Safety Locations for installing ISOFIX child seats In accordance with European Regulations, this table indicates the options for installing ISOFIX child seats on seats in the vehicle fitted with ISOFIX mountings. In the case of universal and semi-universal ISOFIX child seats, the ISOFIX size category, determined by a letter from A to G , is indicated on the child seat next to the ISOFIX logo.
Page 253 Safety IUF: seat suitable for the installation of an For advice on securing of the top belt, refer to Remove and stow the head restraint ISOFIX U niversal seat, " Forwards-facing" the "Isofix Mountings" section. before installing a child seat on a secured using the top strap to the top X: seat not suitable for the installation of a passenger seat.
Page 254 Safety Locations for installing ISOFIX child seats mountings. In the case of universal and semi-universal ISOFIX child seats, the ISOFIX size category, determined by a letter from A to G , is indicated on the child seat next to the ISOFIX logo. Weight of the child / indicative age Less than 10 kg Less than 10 kg...
Page 255 Safety IUF: seat suitable for the installation of an For advice on securing of the top belt, refer to Remove and stow the head restraint ISOFIX U niversal seat, " Forwards-facing" the "Isofix Mountings" section. before installing a child seat on a secured using the top strap to the top X: seat not suitable for the installation of a passenger seat.
Page 256 Safety Advice on child seats Children at the front The incorrect installation of a child seat in a As a safety precaution, do not leave: vehicle compromises the child's protection in one or more children alone and The legislation on carrying a child on the the event of an accident.
Page 257: Manual Child Lock
Safety Manual child lock This mechanical system prevents opening of the rear door using its interior control. The control is located on the edge of each rear door. Locking Unlocking Using the integral ignition key, turn the Using the integral ignition key, turn the control as far as it will go: control as far as it will go: - to the left on the left-hand rear door,...
Page 258: Temporary Puncture Repair Kit
Practical information Temporary puncture repair kit Access to the kit Complete system consisting of a compressor and a sealant cartridge which permits temporary repair of a tyre so that you can drive to the nearest garage. It is designed to repair most punctures which could affect the tyre, located on the tyre tread or shoulder.
Page 259: List Of Tools
Practical information List of tools All of these tools are specific to your vehicle and can vary according to equipment. Do not use them for other purposes. 12 V compressor. Contains a sealant cartridge for the temporary repair of a tyre and can also be used for adjusting tyre pressures.
Page 260 Practical information Description of the kit The tyre inflation pressures are given on this A. "Sealant" or "Air" position selector. Sealant cartridge. label. B. On "I" / off "O" switch. G. White pipe with cap for repair. C. Deflation button. H.
Page 261: Repair Procedure
Practical information Repair procedure 1. Sealing Switch off the ignition. Uncoil the white pipe G fully. Connect the compressor's electric plug to Turn the selector A to the "sealant" Unscrew the cap from the white pipe. the vehicle's 12 V socket. position.
Page 262: Tyre Under-Infl Ation
Practical information Switch on the compressor by moving Remove the kit and screw the cap back on the switch B to position "I" until the tyre the white pipe. pressure reaches 2.0 bars. Take care to avoid staining your vehicle The sealant is injected into the tyre under with traces of fluid.
Page 263 Practical information 2. Inﬂ ation Turn the selector A to the "air" Connect the compressor's electric plug to Adjust the pressure using the compressor position. the vehicle's 12 V socket. (to inflate: switch B in position "I" ; to Uncoil the black pipe H fully. Start the vehicle again and leave the deflate: switch B in position "O"...
Page 264 Practical information Stow the black pipe. Beware of discharges of fluid. Detach the angled base from the white pipe. The expiry date of the fluid is indicated Support the compressor vertically. on the cartridge. Unscrew the cartridge from the bottom. The sealant cartridge is designed for single use;...
Page 265: Checking Tyre Pressures
Practical information Checking tyre pressures / inflating accessories You can also use the compressor, without Connect the compressor's electrical Should the pressure of one or more injecting any product, to: connector to the vehicle's 12 V socket. tyres be adjusted, it is necessary to check or adjust the pressure of your tyres, Start the vehicle and let the engine run.
Page 266: Changing A Wheel
Practical information Changing a wheel Procedure for changing a faulty wheel for the spare wheel using the tools provided with the vehicle. Access to the tools List of tools * All of these tools are specific to your vehicle and can vary according to the level of equipment.
Page 267 Practical information Access to the spare wheel The spare wheel is located in the boot under the floor. For access to the spare wheel, refer to the "Access to the tools" section. Putting the spare wheel back in place Return the wheel to its housing. Return the box to its position in the middle Unscrew the central screw a few turns, of the wheel.
Page 268 Practical information Changing a wheel Procedure for changing a wheel with a punctured tyre by the spare wheel using the tools provided with the vehicle. Access to the vehicle's tools * 2. Wheel chocks for immobilising the vehicle (except versions with manual gearbox). 3.
Page 269: Taking Out The Spare Wheel
Practical information Access to the spare wheel * Taking out the spare wheel The spare wheel is supported by a carrier underneath the vehicle. Fold the concertina board and put the left Detach the wheel/box assembly from the hand third row seat into position (if your rear of the vehicle.
Page 270 Practical information Stowing the tools Return the tools to the box and stow the box in the vehicle's boot. Wind in the carrier by turning the wheelbrace clockwise: once the cable is fully wound in you should no longer feel any resistance.
Page 271 Practical information Position the spare wheel on the box so that Pass the hook with its connection plate into Raise the wheel/box assembly underneath the positioning indicator will be introduced the wheel then the box, as illustrated. the vehicle by turning the carrier drive nut into the bolt hole in the middle of the box.
Page 272: List Of Operations
Practical information Parking the vehicle Immobilise the vehicle where it does not block traffic: the ground must be level, stable and not slippery. Apply the parking brake unless it has been programmed to automatic mode, switch off the ignition and engage first gear * to block the wheels.
Page 273 Practical information Place the jack 3 in contact with one of the Extend the jack 3 until its base plate is in Raise the vehicle until there is sufficient two front A or rear B locations provided on contact with the ground. Ensure that the space between the wheel and the ground the underbody, whichever is closest to the centreline of the jack base plate is directly...
Page 274: Fitting A Wheel
Practical information Fitting a wheel Fitting the "space-saver" spare wheel If your vehicle is fitted with alloy wheels, when tightening the bolts on fitting, it is normal to notice that the washers do not come into contact with the "space-saver" spare wheel. The wheel is secured by the conical surface of each bolt.
Page 275 Practical information Lower the vehicle fully. Tighten the security bolt using the The tyre inflation pressures are given Fold the jack 3 and detach it. wheelbrace 1 fitted with the security on this label. socket 5 (depending on equipment). Tighten the other bolts using the wheelbrace 1 only.
Page 276: Snow Chains
Practical information Snow chains In wintry conditions, snow chains improve traction as well as the behaviour of the vehicle when braking. Use only chains designed to be fitted the type Advice on installation The snow chains must be fitted only of wheel on your vehicle: to the front wheels.
Page 277: Changing A Bulb
Practical information Changing a bulb Front lamps Risk of electrocution Xenon bulbs (D5S-25W) must be replaced by a CITROËN dealer or a qualified workshop. For H7 type bulbs with lugs... take care to observe their correct installation so as to ensure the best lighting performance. In some weather conditions (e.g.
Page 278 Practical information The headlamps are fitted with polycarbonate glass with a protective coating: do not clean them using a dry or abrasive cloth, nor with a detergent or solvent product, use a sponge and soapy water or a pH neutral product, when using a high pressure washer on persistent marks, do not keep the lance directed towards the...
Page 279: Main Beam Headlamps
Practical information Dipped beam headlamps Main beam headlamps Daytime running lamps / sidelamps (halogen model) (halogen model) For the replacement of this type of LED lamp Turn the protective plastic cover to Remove the protective plastic cover by and lighting guides, contact a CITROËN dealer remove it.
Page 280: Front Fog Lamps
Practical information Direction indicators Direction indicators (light Front foglamps emitting diodes - LED) Unclip the finisher by pulling at the top. For the replacement of this type of lamp, Faster flashing of a direction indicator Remove the two screws to remove the unit. contact a CITROËN dealer or a qualified warning lamp (left or right) indicates a Turn the bulb holder a quarter turn.
Page 281: Rear Lamps
Practical information Door mirror spotlamps Rear lamps Direction indicator (PY21W amber). 2. Sidelamp / foglamp (P21/5W). Model with conventional bulb lamps You should contact a CITROËN dealer or a 3. Brake lamp / sidelamp (P21/5W). qualified workshop for the replacement of the 4.
Page 282 Practical information Model with LED lamps Lamps on the tailgate Identify the failed bulb. Remove the three lamp fixing screws A . Open the boot. Disconnect the lamp connector. Remove the access cover. Carefully remove the lamp from the outside by pressing the retaining clip B.
Page 283 Practical information Rear lamps Model with LED lamps Model with conventional bulb lamps Direction indicator (PY21W amber). 2. Sidelamp / foglamp (P21/5W). 3. Sidelamp (light emitting diodes-LED). 3. Sidelamp (P21/5W). 4. Brake lamp (light emitting diodes-LED). 4. Brake lamp / sidelamp (P21/5W). 5.
Page 284 Practical information Lamps on the tailgate Model with LED lamps Identify the failed bulb. Remove the three lamp fixing screws A. Open the boot. Disconnect the lamp connector. Remove the access cover. Carefully remove the lamp from its housing. Turn the bulb holder a quarter of a turn anti-clockwise and pull the bulb out.
Page 285 Practical information Direction indicator, sidelamp and Third brake lamp (light emitting Number plate lamps (W5W) foglamp diodes-LED) Access is by passing a hand under the bumper. For the replacement of this type of lamp, Insert a thin screwdriver into one of the Turn the bulb holder a quarter of a turn and contact a CITROËN dealer or a qualified cutouts in the the lens.
Page 286: Changing A Fuse
Practical information Changing a fuse Access to the tools Changing a fuse Before changing a fuse: the cause of the failure must be identified and rectified, all electrical consumers must b switched off, the vehicle must be immobilised with the ignition off, Good Failed...
Page 287: Installing Electrical Accessories
Practical information Configurations Installing electrical accessories Your vehicle's electrical system is designed to operate with standard or optional equipment. Before installing other electrical equipment or accessories on your vehicle, contact a CITROËN dealer or a qualified workshop. The type of electrical system of the vehicle depends on its level of equipment. To identify the type of electrical system on your vehicle, open the bonnet: the presence of an CITROËN will not accept responsibility additional fusebox in front of the battery indicates that it is type 2.
Page 288: Dashboard Fuses
Practical information Dashboard fuses Type 1 fuse tables Fusebox 1 Fuse N° Rating Functions Steering mounted controls Touch screen tablet, audio and navigation system, CD player, 20 A USB ports and auxiliary sockets. 15 A Front 12V socket. 15 A Boot 12V socket.
Page 289 Practical information Fusebox 2 Fuse N° Rating Functions 15 A Rear 12V socket.
Page 290 Practical information Type 2 fuse tables Fuse N° Rating Functions START/STOP button. Touch screen tablet, audio and navigation system, CD player, F6 A 15 A USB ports and auxiliary sockets. Alarm. Steering mounted controls. Instrument panel. Rain and sunshine sensor. Airbags.
Page 291: Engine Compartment Fuses
Practical information Engine compartment fuses Access to the fuses The fusebox is placed in the engine compartment near the battery (left-hand side). Unclip the cover, by pushing the two red latches towards the rear of the vehicle. Change the fuse (see corresponding paragraph).
Page 292 Practical information Type 1 fuse table Fuse N° Rating Functions 10 A Right hand main beam 10 A Left hand main beam. Type 2 fuse table Fusebox 1 Fuse N° Rating Functions 30 A Motorised tailgate. 25 A Hi-Fi amplifier. Hands-free starting reader unit.
Page 293: Access To The Battery
Practical information 12 V battery Procedure for starting the engine using another battery or charging a discharged battery. Access to the battery Starting using another battery When your vehicle's battery is discharged, the engine can be started using a slave battery (external or on another vehicle) and jump lead cables.
Page 294: Disconnecting The Cable
Practical information Before disconnecting the battery Wait 2 minutes after switching off the ignition before disconnecting the battery. Close the windows and the doors before disconnecting the battery. Following reconnection Disconnecting the (+) cable of the battery Raise the locking tab D fully to release the Following reconnection of the battery, switch on cable terminal clamp E.
Page 295: Charging The Battery Using A Battery Charger
Practical information Charging the battery using The batteries contain harmful substances Protect your eyes and face before a battery charger such as sulphuric acid and lead. They handling the battery. must be disposed of in accordance All operations on the battery must be The Stop &...
Page 296: Load Reduction Mode
Practical information Load reduction mode Energy economy mode Exiting economy mode System which manages the use of certain System which manages the duration of use of functions according to the level of charge certain functions to conserve a sufficient level These functions are reactivated automatically remaining in the battery.
Page 297: Changing A Wiper Blade
Practical information Changing a wiper blade Before removing a front Fitting wiper blade Put the corresponding new wiper blade in place and clip it. Within one minute after switching off Fold down the wiper arm carefully. the ignition, operate the wiper stalk to position the wiper blades vertically on the windscreen, From one minute after switching off the...
Page 298: Towing The Vehicle
Practical information Towing the vehicle Procedure for having your vehicle towed or for towing another vehicle using the towing eye. Access to the tools General recommendations Observe the legislation in force in your country. Ensure that the weight of the towing vehicle is higher than that of the towed vehicle. The person at the wheel of the towed vehicle must have a valid driving licence.
Page 299: Towing Your Vehicle
Practical information Towing your vehicle Towing another vehicle Place the gear lever in neutral (position N on an electronic or automatic gearbox). Failure to observe this instruction could result in damage to certain components (braking, transmission...) and the absence of braking assistance the next time the engine is started.
Page 300: Towing A Trailer
Practical information Towing a trailer Towbar suitable for the attachment of a We recommend the use of genuine Driving with a trailer places greater trailer or installation of a bicycle carrier, with CITROËN towbars and their harnesses demands on the towing vehicle and the additional lighting and signalling.
Page 301: Driving Advice
Practical information Driving advice Distribution of loads Cooling Braking Distribute the load in the trailer so that the Towing a trailer on a slope increases the Towing a trailer increases the braking distance. heaviest items are as close as possible to temperature of the coolant.
Page 302: Roof Bars
Practical information Roof bars Version without longitudinal Version with longitudinal For safety reasons and to avoid damaging the roof, it is essential to use transverse roof bars bars bars that are approved for your vehicle. Observe the fitting instructions and the conditions of use given in the information provided with the roof bars.
Page 303 Practical information Recommendations Maximum load, distributed over the roof bars, for a loading height not exceeding Distribute the load evenly, avoiding 40 cm: 80 kg. overloading on one side. This value is subject to change, please Arrange the heaviest part of the load as check the maximum load stated in the close as possible to the roof.
Page 304: Very Cold Climate Screen
Practical information Very cold climate screen * Removable protective screen which prevents the accumulation of snow at the radiator cooling fan. Fitting Removal Offer up the very cold climate screen to Use a screwdriver as a lever to release the front of the lower section of the front each fixing clip in turn.
Page 305: Transport Systems
(Grand C4 Picasso)... If a towbar and wiring harness are fitted outside the CITROËN dealer network, the installation must be done strictly in line with the manufacturer's recommendations.
Page 306 Practical information "Multimedia": Installation of radio Depending on the legislation in force communication in the country, it may be compulsory Speakers, Hi-Fi module, Bluetooth hands-free transmitters to have a high visibility safety vest, system, head-up display screen, portable warning triangle, breathalyzers and satellite navigation system, semi-integral Before installing any after-market radio spare bulbs and fuses available in the...
Page 307 Checks Bonnet Before doing anything under the bonnet, switch off the Stop & Start system to avoid any risk of injury resulting from an automatic change to START mode. Lift the safety catch and raise the bonnet. Unclip the stay from its housing and place it in the support slot to hold the bonnet open.
Page 308: Petrol Engines
Checks Petrol engines checking the levels of the various fluids and for replacing certain components. Screenwash and headlamp wash reservoir. 2. Coolant reservoir. 3. Brake fluid reservoir. 4. Battery / Fuses. 5. Fusebox. 6. Air filter. Engine oil dipstick. 8. Engine oil filler cap.
Page 309: Diesel Engines
Checks Diesel engines The various caps and covers allow access for checking the levels of the various fluids, for replacing certain components and for priming the fuel system. Screenwash and headlamp wash reservoir. 2. Coolant reservoir. 3. Brake fluid reservoir. 4.
Page 310: Low Fuel Level
Checks Fuel Capacity of the tank: approximately 57 litres (petrol) or 55 litres (Diesel). Low fuel level Refuelling When the low fuel level is reached, this warning lamp in the instrument panel comes on, accompanied by an audible warning, a message and the last bar of the fuel gauge comes on in orange.
Page 311: Fuel Cut-Off
Checks Fuel cut-off Your vehicle is equipped with a safety device which cuts off the fuel supply in the event of a The petrol or Diesel engine of your vehicle is collision. fitted with a catalytic converter, a device which helps to reduce the level of harmful emissions in the exhaust gases.
Page 312: Misfuel Prevention (Diesel)
Checks Misfuel prevention (Diesel) * Mechanical device which prevents filling the tank of a Diesel vehicle with petrol. It avoids the risk of engine damage that can result from filling with the wrong fuel. Operation Travelling abroad It remains possible to use a fuel can to fill the tank.
Page 313 Checks Quality of the fuel used for Quality of the fuel used for petrol engines Diesel engines The petrol engines are perfectly compatible The Diesel engines are perfectly compatible with E10 or E24 type petrol biofuels (containing with biofuels which conform to current and 10 % or 24 % ethanol), conforming to European future European standards (Diesel fuel which standards EN 228 and EN 15376.
Page 314: Running Out Of Fuel (Diesel)
Checks Running out of fuel (Diesel) 1.6 litre HDi engine Fill the fuel tank with at least five litres of diesel. Open the bonnet. If necessary, unclip the styling cover for access to the priming pump. On vehicle fitted with HDi engines, the fuel Squeeze and release the priming pump system must be primed if you run out of fuel;...
Page 315: Checking Levels
Checks Checking levels Check all of these levels regularly, in line with the maintenance and warranty guide. Top them up if necessary, unless otherwise indicated. If a level drops significantly, have the corresponding system checked by a CITROËN dealer or a qualified workshop. Take care when working under the bonnet, as certain areas of the engine may be extremely hot (risk of burns) and the cooling fan could start at any time (even with the ignition off).
Page 316: Brake Fluid Level
Checks Brake fluid level Fluid speciﬁ cation The brake fluid level should be close The coolant level should be close to the "MAX" mark. If it is not, check to the "MAX" mark but should never The coolant must conform to the the brake pad wear.
Page 317 Checks Screenwash/headlamp Diesel fuel additive level Used products wash level low (Diesel with particle emissions filter) fluids with the skin. In the case of vehicles fitted with The additive reservoir low level is Most of these fluids are harmful to headlamp washers, when the fluid indicated by fixed illumination of this health or indeed very corrosive.
Page 318: Oil Filter
Checks Checks Unless otherwise indicated, check these components in accordance with the maintenance and warranty guide and according to your engine. Otherwise, have them checked by a CITROËN dealer or a qualified workshop. 12 V battery Air filter and passenger compartment filter Particle emissions filter (Diesel) The battery does not require any maintenance.
Page 319: Manual Gearbox
Checks Manual gearbox Brake pads Electric parking brake The gearbox does not require any Brake wear depends on the style maintenance (no oil change). This system does not require any of driving, particularly in the case Refer to the maintenance and routine servicing.
Page 320: Dimensions (In Mm)
Technical data Dimensions (in mm) These dimensions have been measured on a vehicle that is not loaded. * Mirrors folded.
Page 321 Technical data Dimensions (in mm) These dimensions have been measured on an unladen vehicle. * Mirrors folded.
Page 322: Identifi Cation Markings
Technical data Identiﬁ cation markings Various visible markings for the identification of your vehicle. D. Tyre/paint label. This label, affixed to the centre pillar, on the driver's side, contains the following information. - the tyre inflation pressures with and without load, - the tyre sizes (including the tyre load index and speed rating), - the inflation pressure for the spare...
Page 324 This handbook describes all of the equipment Automobiles CITROËN declares, by application available in the whole range. of the provisions of the European regulation (Directive 2000/53) relating to End of Life Vehicles, Your vehicle will be ﬁ tted with some of this that it achieves the objectives set by this regulation equipment described in this document, depending and that recycled materials are used in the...
Page 325 13B78.0041 Anglais 2013 – DOCUMENTATION DE BORD 4Dconcept Diadeis Edipro CRÉATIVE TECHNOLOGIE...

CITROËN C4 Picasso Owner's Handbook Manual

Quick Links

Related Manuals for CITROËN C4 Picasso

Summary of Contents for CITROËN C4 Picasso