Konica Minolta drypro 832 Service Manual page 411

Error
Error Error
Message (Display
Level Code
Characters)
E 4121 The operation
was not
performed
normally
E 4122 The operation
was not
performed
normally
E 4124 The operation
was not
performed
normally
E 4125 Tray-1 is open
E 4126 The operation
was not
performed
normally
E 4227 The operation
was not
performed
normally
E
4228 The operation
was not
performed
normally
E 4243 Tray-2 settings
are incorrect
E 4410 Occurrence of
film jam
E 4411 Occurrence of
film jam
E 4412 Occurrence of
film jam
E 4510 Occurrence of
film jam
Error contents
The FILM height detection sensor did not
switch ON during CH1 elevating plate
raising operation.
The elevation HP sensor did not switch
ON during the CH1 elevating plate
lowering operation.
The tray detection sensor did not switch
OFF during the CH1 film loading
operation.
The tray detection sensor switched OFF
during operations other than the CH1 film
loading operation.
The pickup evacuation sensor did not
switch OFF during CH1 pickup
operation.
The elevation HP sensor did not switch
OFF during the CH2 elevating plate
raising operation.
The elevation HP sensor did not switch
OFF during the CH2 elevating plate
raising operation.
CH2 supply unit is set to be used, even
though it is not present.
Film remains at position regulation unit.
Film did not arrive at feed inlet sensor.
Film remains at position regulation unit.
Film remains at feed inlet sensor.
Film remains at position regulation unit.
Film remains at position regulation FILM
detection sensor.
Film remains at position regulation unit.
Film does not arrive at the V-SYNC
sensor.
Chapter 17 Troubleshooting
Error Support: Service
•
Shake the tray, and re-insert the film
•
Check the connection and operation of the elevating
plate motor and mechanical control board
•
Check the connection and operation of the FILM
height detection sensor and mechanical control
board
•
Replace mechanical control board
•
Shake the tray, and re-insert the film
•
Check the connection and operation of the elevating
plate motor and mechanical control board
•
Check the connection and operation of the elevating
HP sensor and mechanical control board
•
Replace mechanical control board
•
Replace tray detection unit
•
Check the connection and operation of the tray
detection sensor and mechanical control board
•
Check the connection and operation of the tray lock
solenoid and mechanical control board
•
Replace mechanical control board
•
Replace pickup unit
•
Check the connection and operation of the pickup
evacuation motor and mechanical control board
•
Check the connection and operation of the pickup
evacuation sensor and mechanical control board
•
Replace mechanical control board
•
Shake the tray, and re-insert the film
•
Check the connection and operation of the elevating
plate motor and mechanical control board
•
Check the connection and operation of the elevating
HP sensor and mechanical control board
•
Replace mechanical control board
•
Check connection between the CH2 supply unit and
mechanical control board
•
Replace mechanical control board
•
Check the connection and operation of the feed
motor and mechanical control board
•
Check the connection and operation of the feed nip
motor and mechanical control board
•
Check the connection and operation of the feed inlet
sensor and mechanical control board
•
Replace mechanical control board
•
Check the connection and operation of the feed
motor and mechanical control board
•
Check the connection and operation of the position
transportation motor and mechanical control board
•
Check the connection and operation of the feed nip
motor and mechanical control board
•
Check the connection and operation of the position
regulation FILM detection sensor and mechanical
control board
•
Replace mechanical control board
•
Check the connection and operation of the feed
motor and mechanical control board
•
Check the connection and operation of the position
transportation motor and mechanical control board
•
Check the connection and operation of the feed nip
motor and mechanical control board
•
Check the connection and operation of the V-SYNC
sensor and mechanical control board
•
Replace mechanical control board
17-23