D-Link xStack DGS-3620 Reference Manual page 600

xStack® DGS-3620 Series Layer 3 Managed Stackable Gigabit Switch CLI Reference Guide
type_1 - Specifies an OSPF AS-external type-1 route.
type_2 - Specifies an OSPF AS-external type-2 route.
interface - Specifies to match the outgoing interface of the imported route.
<ipif_name 12> - Enter the outgoing interface name. This name can be up to 12 characters
long.
route_source - Specifies to match the source of the imported route.
<list_name 16> - Enter the route source name. This name can be up to 16 characters long.
set - Specifies to define the conditions for redistributing routes from one routing protocol into
another.
add - Specifies the set to add.
delete - Specifies the set to delete.
next_hop - Specifies the IPv4 next hop attribute.
<ipaddr> - Specifies the IPv4 address to set.
peer_address - This will take effect for both the ingress and egress directions. When set to
next_hop to peer address, for ingress direction, the next hop will be set to the neighbor
peer address. For egress direction, the next hop associated with the route in the packet will
be the neighbor peer address.
metric - Specifies to set the metric.
<uint 0-4294967294> - Enter the metric value used here. This value must be between 0 and
4294967294.
local_preference - Specifies to set the local preference for the matched route.
<uint 0-4294967295> - Enter the local preference value used here. This value must be
between 0 and 4294967295.
weight - Set the weight for the matched routes. It will overwrite the weight specified by the
neighbor weight command for the routes received from the neighbor. If weight is neither
specified by the neighbor weight command nor set by the route map, then routes learned
through another BGP peer have a default weight of 0. This will only take effect for ingress
direction.
<value 0-65535> - Enter the weight value used here. This value must be between 0 and
65535.
as_path - Specifies an AS path list which is used to prepend the AS list.
<aspath_list> - Enter the AS path list value used here.
community - Specifies a community to be used or to be appended to the original communities of
the route.
community_set - Specifies a community set used.
<community_set 80> - Enter the community set value used here. This value can be up to
80 characters long.
internet - Specifies that routes with this community will be sent to all peers either internal or
external.
no_export - Specifies that routes with this community will be sent to peers in the same AS or
in other sub autonomous systems within a confederation, but will not be sent to an external
BGP (eBGP) peer.
no_advertise - Specifies that routes with this community will not be advertised to any peer
either internal or external.
local_as - Specifies that routes with this community will be sent to peers in the same AS, but
will not be sent to peers in other sub-AS's in the same confederation and to the external
peers.
additive - (Optional) Specifies that the community string will be appended to the original
community string. If not specified, the specified community string will replace the original
community string.
origin - Specifies to set the origin for the route.
egp - Specifies that the origin for the route will be set to EGP.
igp - Specifies that the origin for the route will be set to IGP.
incomplete - Specifies that the origin for the route will be set to 'incomplete'.
dampening - Specifies the dampening timer and parameter used.
<min 1-45> - Enter the dampening time used here. This value must be between 1 and 45
minutes.
<value 1-20000> - Enter the dampening parameter value here. This value must be beteen 1
and 20000.
<value 1-20000> - Enter the dampening parameter value here. This value must be beteen 1
595